Question about Washing Machines

1 Answer

Have error code 5Ud can you explain what this is as manual does not have code listed?

Posted by Anonymous on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

It is actually "SUd" probably didn't use enough softner/too much detergent. i clear it by running "quick wash" with no addidtives, gives me two rinse cycles in 35 minutes, done.

Posted on Jul 14, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Machine is not spinning to get excess water out. code 5ud showing on screen


5UD is actually 'SUDS', it means the pump has noticed there is too much soap and is having difficulty pumping out. Are you using HE detergent?

If you leave the machine for an hour and then set it to Rinse and Spin, it should clear.

Jan 24, 2017 | Washing Machines

2 Answers

What does 5ud mean 10 minutes from finishing 5 Ud displayed can't open door?


The SUD (not 5UD) code is displayed when excess foam is detected (possibly because excessive detergent is being used). If your machine does not cure itself, you may have to run an "Eco drum clean" cycle (if your machine has it) or a 90 degree cotton cycle with no detergent and no load.

Aug 29, 2016 | Samsung Washing Machines

2 Answers

Please give me a solution about DDL-8700A-7 ERROR-808 Error-302


Kindly read a manual or visit dealer close to you.

Jul 23, 2016 | Sewing Machines

1 Answer

PLS GIVE SALUTION OF ERROR 7 IN LK-1900ASS


Most owner's manuals have a list of error codes at the back of the book that explains the problem and the suggested resolution. Since the make of the machine was not included with this question, we cannot provide further assistance other than to suggest searching the internet for:

Make + Model + the words "error code"

///

Jan 28, 2016 | Sewing Machines

1 Answer

Washer code 5ud


Hello & Welcome to FixYa

Sud error is displayed when the washer is unable to drain, press PAUSE/CANCEL button twice to clear the display. After this please check the drain hose and drain pump filter for any blockages and make sure it is not clogged with foreign particles. You can also check the drain pump to verify that its working. Please get back to me if you have any other questions.

Kevin

Dec 02, 2011 | Kenmore Elite 45986 Front Load Washer

1 Answer

My washer is giving me code 5ud. What does this


The F35 indicates that the main control board detects a problem with the analog pressure sensor (water level pressure switch) in the washer. This component senses and controls water level in the washer. This failure could be caused by a pinched or broken air hose between the air trap at the bottom of the washer tub and the analog pressure sensor. It can also be caused by a clogged air trap or a failed analog pressure sensor. If you are able to unplug the washer and pull off the top panel, you can check for the probable cause of this failure.

To remove the top panel, remove the screws on the very back of the panel that secure it to the washer cabinet. Pull the top panel back slightly and then and off of the washer. It is on the side wall just behind the expansion control board. You can check the air pressure hose connection and the wire harness connection on this component.

This component costs around $99.This information was based on the general description of the washer model that you provided (Kenmore Elite front load washer). There are several different models of this washer.

The following link explains the error in more detail and how to correct:

http://www.fixya.com/support/r3608687-sud_error

NOTE: If these preliminary measures do not correct your problem, you may have to replace the drain pump. It does not take much to damage the pump impeller or motor. Since the error code can be generated if the drain cycle exceeds 8 minutes, if the pump is damaged and can't pump at the required volume, the error code will continue to appear until the pump is replaced.

COURTESY:jsrock - A senior expert of fixya.....

Jul 04, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Error code 5ud or Sud


The front panel is displaying "SUD". This is a Suds Detect error code. The washer will not complete any cycle as long as the error code is present. The following link explains the error and some potential causes:

http://www.fixya.com/support/r3608687-sud_error

The number one cause of the error comes from using too much, or the wrong type, of detergent. You are required to use High Efficiency (HE) detergent with these washers because the concentration is formulated for HE washers that use small amounts of water. Using the wrong type of detergent can also void any manufacturer warranty you may have.

NOTE: HE detergent does not have a lot of suds, which often confuses consumers into thinking they aren't using enough detergent. With HE washers little to no suds is NORMAL and preferred.

If too much deteregent has been used, using the RINSE/SPIN is recommended to flush the tub, drain pump and lines. IMPORTANT: It can sometimes take several cycles to clear. Also, leaving the door open for a while can allow air into a suds filled drum to get rid of some of the bubbles.

Secondary causes can come from something restricting the drainage system. Most notably, something lodged in the drain pump and/or drain hose(s). I've included a follow-on link that explains how to check the drain pump reservior if required.

Each one of these washers come with a technical data sheet inside.

To access, you will need to remove the lower toe panel under the door. The access screws are located under the bottom front edge of the panel. You may have to prop the two front feet of the washer up for better access ( a 2x4 works well for this). With the screws removed, the panel should drop down, then come off. If the tech sheet isn't directly behind the panel, it will be affixed to one of the interior cabinet walls.

The tech sheet lists all error code definitions, troubleshooting data, diagnostics procedures and wiring diagrams. I mention the tech sheet because you may need it from time to time to troubleshoot your washer.

Read through the information provided and let me know if you have any further questions. I hope this can help you.

Jun 08, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Error Codes"5ud" and "02" and "F"


The two error codes together indicate you have something restricting the drainage system. "F02"is a Long Drain error code, "SUDS" occurs when too much air is sensed in the drainage system. In most cases, the drain pump reservoir needs to be cleaned out. The following link explains how:

http://www.fixya.com/support/r3574284-checking_the_drain_pump_on_a_front_loade

If you check the drain pump reservoir and the problem still persists, you may have a pump with a damaged motor/impeller, or something lodged in one of the drain lines. In particular, the drain line that runs from the bottom of the wash tub to the inlet side of the pump.

I recommend you remove the inlet hose, first and inspect for clogs. In is common for small garments to become lodged in this area and restrict water flow to the drain pump. Check the output drain line for obstructions as well.

It does not take much to damage this small drain pumps. The error code is generated if the drain cycle exceeds 8 minutes. So...if the impeller or motor become damaged, and the pump does not pull water at the correct volume, you may still experience the drain error. In this case, you will have to replace the pump in order to get the error to clear. The following link explains how:

http://www.fixya.com/support/r3574350-replacing_the_drain_pump_in_a_front_load

Replacements can be purchased at any of the following websites:

searspartrsdirect.com
pcappliancerepair.com
appliancepartspros.com
repairclinic.com

Prices vary between sites, so shop and compare. the first three sites listed also have helpful exploded view parts illustrations to assist you with locating and properly identifying the parts you may need.

If you have any questions, please post back and let me know. I hope this helps you.

Mar 12, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Where can I find a list of diagnostic error codes for a 2004 Pontiac Grand Am?


MOST DIAGNOSTIC COMPUTERS CODE RETREAVERS ONELY GO BACK AS FAR AS 2006. BUT I HAVE A 1994 CHEVY LUMINA APV LS VAN, AND I BOUGHT A REPAIR MANUAL by CHILTON WHICH EXPLAINED HOW TO RETREAVED ERROR CODES WITHOUT THE USE OF A CODE RETREAVER. TRY THAT. OTHER WISE YOU MIGHT BE ABLE TO GET INSTRUCTION FROM THE MANUFACTORY.

Oct 20, 2009 | 2004 Pontiac Grand Am

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

1,812 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

yadayada
yadayada

Level 3 Expert

74896 Answers

Brad Brown

Level 3 Expert

15441 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...