Question about Projection Televisions

1 Answer

The power on dual deck VCR DDV 3110 does not turn on.

Posted by on

  • 4 more comments 
  • aadelawalla Apr 20, 2008

    Would I get response on my email for the solution of the problem, if so, how soon ?



    Pl advise.

  • aadelawalla Apr 20, 2008

    Where is the fuse box on the dual deck VCR ?

  • aadelawalla Apr 20, 2008

    OK, Please advise asap on my email. Thanks.

  • aadelawalla Apr 20, 2008

    Thanks, but I am waiting for your reply on my email for the solution of the problem.

  • aadelawalla Apr 20, 2008

    I could not find the fuse box on the back of the VCR near AC line.



    Please advise me a contact telephone number for a local technician who can fix the problem.



    Please advise me by return email.



    Thanks.

  • aadelawalla Apr 20, 2008



    The problem has not been resolved and I am not satisfied with the solution given to me as it did not produce any result.



    Please refund me the total amount of money paid by me.



    Thank you.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,665 Answers

Check for any fuse blown

Posted on Apr 20, 2008

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Tape is stuck in the vcr and when you turn on the power it turns the tape about 10 seconds and then shuts off the power.


if the tape has snagged inside, the only way to get it out is to take the top of the vcr off and manually remove it. very simple procedure. only use your fingers and not anything sharp. have you tried rewinding the tape (from STOP mode) sometimes tapes can end up being wound very tight which would have the same effect. if you can rewind do so, then fast forward until tape stops, repeat this a few times this should loosen the tape.

Sep 21, 2008 | Projection Televisions

1 Answer

GoVedio duel deck VCR Model # GV3060x will not turn on. Fuse is good but change it out anyway but it did not cure my problem.


the problem can be due to some other component on the power board. have u replaced the power board fully?

Jun 25, 2008 | Projection Televisions

1 Answer

Sharp model dv-rw 360h video deck jams with loud clicking noises when carriage lifts?


Hi thanks for the email, i would like to point out that the Sharp model in question is not a television but a video/dvd combi. And the answer to the problem is to remove the vcr deck and replace and realign the cassette carriage loading gears.Hope this helps others with the same problem.

Sep 11, 2008 | Sharp Projection Televisions

1 Answer

My vcr won't tearn on and its connected to my tv who now can not tearn on and on top of all that in my vcr there is a vhs that I need to return immediatly.


Hi,

Even if the TV is connected to the VCR, chances are that it would only be the signal (RF or Audio/Video) cables and not the power cords. Both not powering on would indicate an electrical problem such as:
1. defective power strip as wall outlet;
2. blown fuse or popped open circuit breaker;
3. a near lightning strike or power outage that has affected the AC section of the 2 devices.

One that you can try is to remove the VCR from its current location and try plugging it elsewhere. If it powers up (and hopefully you can eject the tape that needs to be returned), then you likewise have confirmed the electrical problem,

Alternately, you can manually removed the tape (with the possibility of wrinkling a few areas) by opening the top cover, determining the motor/gear drive that ejects the tape and just basically winging it. Of course your best bet would be to seek the services of a qualified professional.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards.

Thank you for using FixYa.

Apr 28, 2008 | Projection Televisions

1 Answer

VCR won't work


you need to clean the mod switch un the vcr deck but use care when you remove the deck you can take it out of time and then it will not work.

Mar 30, 2008 | Projection Televisions

1 Answer

Rca wont turn on


As long as its a 2200 cap and the voltage is above 16 it will work fine.

Mar 15, 2008 | RCA D52W19 52" Rear Projection Television

2 Answers

RCA big screen TV


Replace splitter RCA #205064, Q4101, U4101, C4102, C4118, C4108

Jan 02, 2008 | RCA P52937 52" Rear Projection Television

Not finding what you are looking for?
Projection Televisions Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

yadayada
yadayada

Level 3 Expert

60867 Answers

Are you a Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...