Question about Audio & Video Receivers

1 Answer

Unable to connect attack3joystick to Windows98SE. Novalogoc F16 multirole fighter loaded.please help.

Posted by on

1 Answer

Hi
was

Posted on May 31, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Panasonic sa-vk800 when the volume up the unit is shoot down than display f16


Check all of your speaker wire connections at both ends for looseness, strand wire fraying/breakage, correct polarity and corrosion. If all are ok, reduce your setting for the amount of bass it outputs.

Dec 15, 2014 | Panasonic Sa-ht70 Home Theater Receiver 5...

1 Answer

Why my panasonic sterio model sa-ak640 says f16 then turns off


F61 usually means the amp has detected a short or a severe microprocessor error.

Generally speaking, an amp attempts to protect itself from heat, shorts, overloads and operator exuberance by refusing to turn on or stay on.

Overloads can be from excessive periods of high output or marginally low impedance loading by the speakers; and shorts would be wiring issues or a speaker blowing up.

You should be able to feel if it's hot. WHY is it overheating? Make sure it has sufficient ventilation on all sides and that vent holes are not blocked by dust balls. Ensure the fan (if equipped) is running as designed (some only operate on demand). Clean dust and debris from it.

If the amp comes back on after cooling, you're lucky. They only have so many self-protection cycles in their lives so continuously resetting or cycling their power without addressing the cause can do more harm than good.

If it protects immediately on a cool power up you should disconnect the speaker connections and try it 'naked'. If it comes up then diagnose which lead(s) are shorted. If it does not come up the problem is internal and should be left to an experienced and competent hands-on tech.

Check for loose speaker connections at the speaker as another possible root cause for intermittent shutdown.

Jul 03, 2011 | Audio & Video Receivers

1 Answer

Can not get the back cordless speakers to connect, everything is connected but no sound?


Hi,
Wireless speakers needs power to run ,unless they are powered by battery (to be loaded into speaker modules) ,I believe you connected each of the wireless speaker to 110 VAC power plug and the transmitter module as well..
Before connecting them to your receiver ,I recommend you test them with something else,i.e..NOTEBOOK Audio output or MP3 player headphones output...
if you succeed then you can connect it to your receiver..
Please make a simple test to make sure wireless speakers are working and if you need more help just let me know ..
Hope this helps! Take care and please Remember to rate/vote and give me 4 Thumbs Up for me to continue for Helping out the Community :) Thanks

Jun 25, 2011 | Audio & Video Receivers

1 Answer

When i use a speaker control switch i am unable to get sound from my second pair of ''b'' speakers. plus i am unable to get my turntable to produce audio


To make sure please switch the working "A" cables and speaker
pairs with "B" connectors and test it again.If it works ,check your "B " cables and speakers..

There are two types of turntable cartridges ..,magnetic and ceramic stylus..
your Turntable should be connected to turntable input.and both turntable and input should be same type as either magnetic ( that requiers phono preamps ) , or ceramic (that needs no preamplification at all ).Please check both your receiver and turntable user manuals to verify the types and decide which one to connect to other..good luck

Jan 07, 2010 | Audio & Video Receivers

1 Answer

I have a QSC EX 2500. Recently, the unit blows a fuse immediatly when powered on. The fuse is located on a circuit board at the inside back left (near the speaker connections). This circuit board has...


it's not a problem it just show u thay ur speaker is unable to bear the load of it . just unplug the switch of the speaker before turn on ur computer and when ur computer turn on plug ur speaker again...

Dec 03, 2008 | Audio & Video Receivers

1 Answer

How do I connect an AKAI xr20 to a Tascam DP-01fx/cd? I am unable to get the multitrack to record the drum machine.


first you have to check the output terminal of the AKA and the input of the tascam. If they have the same feature, you can buy the connector on a store but if they are not of the same feature maybe you can buy a connector for each of those and find an adapter to establish a connection to for it.

P.S. If this helps please rate me. Thanks.

Jul 09, 2008 | Tascam Audio & Video Receivers

3 Answers

Streamium Remote control


Use new batteries for the remote.

May 31, 2008 | Audio & Video Receivers

Not finding what you are looking for?
Audio & Video Receivers Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audio & Video Receivers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

The Knight
The Knight

Level 3 Expert

68301 Answers

yadayada
yadayada

Level 3 Expert

60960 Answers

Are you an Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...