Question about Whirlpool 24 in. ADP5966 Free-standing Dishwasher

1 Answer

Flashes 8 times ADP 5340

Hi there

got a porblem with the unit

flashes 8 times will not start only pump runns then nothing
any idea what the fault could be>

many nks in advance

Ralph

Posted by on

  • Anonymous Mar 27, 2014

    drain pump running all the time and start light flashing no sign of any leaks

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Again Pressed the main button for about 15 sec that did reset the fault

larf

Posted on Apr 21, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hotpoint whirlpool ADP 4502/5


It's trying to fill with water and there is debris in the pump assy. Please remove the debris and restart the unit.

Mar 11, 2014 | Dishwashers

1 Answer

Whirpool ADP 5550. Will only rinse. Does not


It is possible that the machine does not start off the cycle because there are errors due to feedback from the inputs. For the program to start up the main program controller must initiate the INLET/MOTOR/DRAIN pump/ valve to open up and allow each function to be driven starting from the flow of water into the drum as also the drain valve to open to exit the water at the point of the program cycle. If this does not happen then the voltage at the valve/motor/pump must be checked or the fault relates to no voltage from the controller. This means the controller is a suspect.

Make sure that a fault in any of the cycle will relate to the specified action, so check the command from the program module and then the executing device be it the valve or motor or pump.

Please check the link below:

http://www.repairclinic.com/Washing-Machine-Troubleshooting?red=Washing-Machine-Repair-Help

Thank you for using fixya.

Sep 17, 2011 | Whirlpool Dishwashers

2 Answers

Whirlpool adp 6600 will not function start light is just flashing


Whirlpool adp 6600 will not function start light is just flashing. Waht di I do?

Sep 17, 2009 | Whirlpool 24 in. ADP6940 Dishwasher

1 Answer

Dishwasher adp 4601 when switched on the pump activates.and after 2 mins start lamp bliks and pump goes off


The number of flashes indicates the fault. Reset machine by holding down the start button for 3 secs, then start a new cycle. If fault reoccurs, the number of flashes indicates fault eg 3 flashes, stop, 3 flashes stop, indicates F3 fault.
Faults listed below- advice on repair depends on which fault your machine is indicating, but may give you an idea of what to look for
1flash=NTC (temperature sensor) break- NTC outside normal range.
2flash=water leakage-float switch in base activated.
3flash=heating fault(check element.NTC,control board).
4flash=drain error-blockage in pump or drain system,or faulty water indicator switch.
6flash=water inlet fault-check inlet valve, check inlet hose not kinked
7flash=flow meter failure (flow meter measures water intake volume-large plastic weir located on left hand side of machine-reomve side panel to access)
These a most common faults, but further advice on repair requires counting flashes when fault occurs.

Aug 09, 2009 | Whirlpool Dishwashers

1 Answer

Start light flashing wont start cycle, what does it mean


count the number of flashes- this indicates fault ie will flash 4 times stop, flash 4 times stop. To clear fault, hold start button for 3 secs. Try running another fast cycle- if fault reoccurs count flashes: Number of flashes:1=NTC fault, 2=Flood switch activated, 3=Heating fault, 4=drain fault, 6=water inlet fault, 7=flow meter fault, 8=water level fault

Aug 06, 2009 | Whirlpool Dishwashers

2 Answers

Dishwasher light flashes 7 times


although i dont have a lookup for your particular model number. if you remove the lower access panel you will find techsheet/troubleshooter. in it there will be section on "clen light blinking 7x" foplloe direction to put into test mode to clear the fault. belive its,,, heated dry/ sani rinse / heated dry/sani rinse. pushing htese buttons is what gets into test mode

Dec 11, 2008 | Whirlpool 24 in. ADP5962 Free-standing...

3 Answers

Whirlpool adp 5540


My dishwasher isnt working anymore after i cleaned the filters? i took out and cleaned the filters in it and now it doesnt seem to be working properly. it goes thru the cycle but its not cleaning. the dishwashing tablet falls to the bottom and isnt even dissolved completetly after the cycle has finished. is it possible that its blocked somewhere?
It is a Whirlpool ADP 5540
thanks for your help
**** the walls are still dirty after the cycle but there is steam in there as if its done its normal cycle

May 13, 2008 | Whirlpool 24 in. ADP5966 Free-standing...

1 Answer

Whirlpool adp 8540 - 7 flashes


replace the control board in the console

Apr 10, 2008 | Dishwashers

Not finding what you are looking for?
Whirlpool 24 in. ADP5966 Free-standing Dishwasher Logo

Related Topics:

795 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3051 Answers

Are you a Whirlpool Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...