Question about Furuno Navnet 1732 GPS Receiver

1 Answer

Connection to PC for Nav software

I am trying to connect my Furuno 1732 to my PC to be able to utilize Offshore Navigator Lite. I am not getting any GPS data to the PC. Is there a driver that I need to download to the PC to allow this to work?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 65 Answers

Assuming you have GPS input to your 1732 (i.e. GP310/320 sensor), you'll need a 7 pin NMEA data cable (000-154-028) wired to a D-sub 9 pin (serial) plug. The shield goes to pin 5, blue to #3, & white to #2. Jumper pins 7 & 8 together. The 7 pin cable goes to Data port 3 of the 1732.

Posted on Jul 15, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hello, I have a GPS FURUNO GP31 and his screen is out of service and I want to retrieve the data. You can do this ? because I am on vacation until Saturday, August 2 sydney.or i go to melbourne until...


I have posted the Operator Manual at
http://www.offscotland.plus.com/Temp/GP30-GP35-Operator's_Manual.pdf

Use this to check out section 7-10 to make up a cable to connect to a PC to allow download of data. Then, using the manual as a reference figure out the sequence of buttons to press to get the GP31 to download the waypoint and route data to the PC. Just press the buttons and assume the display is showing the next prompt. If you know someone you has a working GP31 get them to do the sequence and write down the buttons they press. You just copy the same sequence. You will need some software on the PC to capture the data,

Jul 30, 2014 | Furuno GP31 GPS Receiver

1 Answer

LOOKING FOR OPERATORS MANUAL FOR FURUNO GPS NAVIGATOR GP-70 MARK 2


You'll find one on the Furuno site - follow the link
http://www.furunousa.com/products/productdetail.aspx?product=GP70MK2&category=Products+%3a+Previous+Products+%3a+GPS+%26+Chart+Plotters+%3a+GPS+Receivers

It's an ominous date to be looking for a manual! Has it stopped working or is it just the date that's wrong?

12 Dec 2010 is 'GPS week number rollover' for the GP-70 Mark 2. See www.furuno.co.jp/en/pdf/080531_notice_en.pdf for details.


I

Dec 12, 2010 | GPS

1 Answer

I would like to know what coloured wires connect to where in a Furuno Gps navigator 31


Thyere are onlyb two wires red and black red is power black is return and the green earth should not be earthed anywhere on the case. If you need the manual contact me admin@nettiser.com.au

Please nrate my help++++Thanks for using FIXYA

dont rate if you have more questions as it locks me out, use email

Oct 17, 2009 | Furuno GP31 GPS Receiver

1 Answer

Can I use my furuno gps navigator to supply position data to my rdp-139 chartplotter and if so which wires need to be connected


Yes the output forom the Furuno GPS (like a GP31) will be yellow and green, hook these to theinput on the plotter blue (or black) and white. Use Data1 on potter as the input and select a nav source of "ALL" in setup menu.

Jun 05, 2009 | Furuno Navnet 1834C/NT vx2 Radar C Map Nt

2 Answers

Raymarine st8002 wired to furuno


The st8002 is not compatble with rs232 data. You need to supply it with nmea 0183 data. You will need to wire it to the "NMEA port IN" on the pilot to NMEA out on your Furuno and turn on the mnea sentances "out" on your Furuno. You will need to turn on at least the following sentances GGA GLL RMB RMC.Hope that helps.

Apr 20, 2009 | Raymarine St8002 Smartpilot Autopilot...

1 Answer

Connect Furuno 1732 to st8002 autopilot


It will handle the voltage. as far as the wiring goes, you'll have to decide which port to use. the wire coloring is different. you'll have to send your nmea out data from port 3 white and shield ( Like you said) to the pilot and receive your heading data from the pilot on port 2.

Apr 11, 2009 | Furuno Navnet 1732 GPS Receiver

1 Answer

Display position on PC


Hi miguel09,

You could try SeaClear It's free and runs not only on Windows systems but also on Linux with Wine. If you want to upload routes and waypoints then you can use this software from Furuno.

Best Regards

Lars Erting

Jul 03, 2008 | Furuno GP31 GPS Receiver

1 Answer

Furuno GP31 - PC wiring instructions


try
http://furuno.inforce.dk/graphics/14_Softwares/09_gps/FURUNO_GP-32_pc_connect.pdf

Jun 27, 2008 | Furuno GP31 GPS Receiver

1 Answer

Wiring


use the yellow and green check for pulsing voltage on wires with digital meter measuring 12V you must turn on the data in the Furuno menus

Mar 07, 2008 | Furuno GP32 GPS Receiver

1 Answer

Communication to Offshore Navigator light


The internal memory battery is dieing. It will eventually stop completely unless you get a new battery installed.

Jul 08, 2007 | ICOM Informatique GP-270ML GPS Receiver

Not finding what you are looking for?
Furuno Navnet 1732 GPS Receiver Logo

Related Topics:

258 people viewed this question

Ask a Question

Usually answered in minutes!

Top Furuno GPS Experts

Ron Dufek
Ron Dufek

Level 3 Expert

398 Answers

Cindy Wells

Level 3 Expert

5101 Answers

Steve
Steve

Level 3 Expert

693 Answers

Are you a Furuno GPS Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...