An expert who has achieved level 2 by getting 100 points
An expert that got 5 achievements.
An expert whose answer got voted for 20 times.
An expert that has 1 follower.
Re: the timer is off.
Check to see if the face of the time has come off. It seems that the cover has come off and been replaced at 180 degrees from the correct position. If there is any type of locating pin or way to match it to the correct orientation, it should be able to reset to a "home" position.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
The numbered bezel can be used by divers to measure elapsed time on their oxygen supply. Place the zero where the minute hand is now and you'll know when 20 or 30 minutes have passed when the minute hand reaches bezel number 20 or 30.
In the same way, you can use the bezel to tell when 30 minutes have passed on your parking meter if you simply put the 0 on the minute hand when you leave the car. When the minute hand reaches the 30 mark, a half hour will have passed.
Typically, the bezel only turns counterclockwise to keep the wearer from bumping and changing the elapsed time number. On some less expensive watches, the numbered bezel does not turn and is decorative only.
The rotating bezel can be used to measure elapsed time. For example, if the time on your watch reads 10.10, align the zero point of the bezel with the minute hand. Now, say the time is 10.40, the minute hand at 8 o'clock will point towards 30 on the bezel, indicating that 30 minutes of time has elapsed since 10.10.
Copy following link for instructions setting analog timers: http://waterheatertimer.org/How-to-set-timers.html
CU750 appears to be Mr Steam with 30 minute digital timer, or 30 minute spring-wound mechanical timer. Copy links following links to download Instruction manuals for these timers: CU 99216DIG timer manual: http://waterheatertimer.org/pdf/Diehl-652-Operating-micro-II.pdf CU 99216B timer manual: http://waterheatertimer.org/pdf/039_FF-series-sell-sheet-with-wiring.pdf http://waterheatertimer.org/Countdown-timer-horsepower-ratings.html
It's a little backward from what I was thinking. The "Stops" haveto be UP for the timer to be OFF. When you want the timer toturn an object ON you push the "Stops" DOWN.Thanks to geno_3245 for posting the initial information.
Melnor 604F Instructions (from Label on unit)All indicator light flashing - replace 9V battery inside unit 1. To Start - turn dial to Off and press Enter. 2. Set Time - set current time and press Enter (Yellow ring). 3. Set Start Time - Set time to start first irrigation cycle (Yellow ring) and press Enter. 4. Frequency - Set frequency of irrigation cycle; e.g., twice a day set 12 h. (red sector ring) and press Enter 5. Duration - Set duration of cycle (Green band) minutes and press Enter. ---------- To change duration - turn dial to new duration and press enter. To turn water on manually - Turn dial to ON position, water will turn off in 30 min. Do not press enter in the OFF position as the unit will clear program. You will have to reprogram unit via steps 2-5 above.
The clock timer might be faulty.Need to Replace it.Since the machine is
new, it must be under warranty and can be subjected to replacement.Problems with
clock timers is common with any washer.Its better when
detected early like in this case.Good luck.Please do post your comments.
Setting Defrost time, Place the start pins(screw pins) in the outer dial, at the time of day- When you want defrost to start. (8am-2pm-8am-2pm) 4 hours min. between hours.
Set the Time of Day, Grasp knob marked - Turn to set. rotate, until the correct time of day. Ever timer there is a power interuption, this will ahve to be re-set.
Depress and rotate the bronze pointer on the inner dial to the length of defrost wanted, - apx 30 minutes.