Question about Garden

1 Answer

I need to adjust the clutch on an older Murray rider. I found how to adjust the clutch rod, and now I can't get it back on.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 78 Answers

Estoboy, navigate to http://www.mytractorforum.com/forumdisplay.php?f=202
And post a picture of your machine. We'll be able to help you better on there. (Tons of Murray guys)

Posted on Jul 12, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Murray rider runs when engage clutch mower dies


Check for excessive resistance in the mower blade mechanism is my best suggestion, you may have a failed part that is jemmin up and overloading the motor.

Jun 07, 2017 | Murray Garden

1 Answer

How to adjust the citing deck on a Murray 8.0 30 inch rider


try Mc Gyver Workshop they may have a video

Mar 09, 2017 | Murray Garden

2 Answers

Where is the choke on the Murray 875 rear rider?


Most of these models have a automatic choke, located on the carburetor. Some are coil springs and others are electronic. There is no manual adjustment on these. Some older models had it included as part of the throttle control. My guess is yours is automatic and is part of the carburetor system.
They are common item to go bad.

Aug 24, 2014 | Garden

1 Answer

Our older Murray Riding Mower is stuck in reverse and will not go into another gear. It will back up but won't come out of reverse. How can we fix it?


Either your clutch is out of adjustment or somebody jammed it into reverse too hard which you would need to take the transmission apart

Sep 15, 2013 | Garden

1 Answer

Adjut clutch


Loosen adjuster on clutch cable completely.

Remove round cover on primary cover.
Loosen lock nut around screw in center of clutch plate.
Back off adjusting screw.
Tighten screw until it JUST touches.
Back off 1/4 turn.
Hold in place while tightening lock nut.

Adjust clutch cable adjuster until there's 1/16-1/8" free play at hand lever.

Feb 03, 2013 | 2001 Harley Davidson FXDL Dyna Low Rider

1 Answer

1979 Harley Davidson FXS Low Rider clutch adjustment


Hi, Michael a proper clutch adjustment for big twins starts by squirting some silicone spray or Brake Kleen into the top of the rubber boot on the clutch cable and sliding it back exposing the cable adjuster. Loosen the jam nut and turn the adjusting screw all the way in so your clutch lever has excessive slop. Remove the Derby cover, loosen the jam nut on the clutch pack adjuster screw and screw it in until light resistance is felt against the clutch rod then back the adjusting screw out 3/4 of a turn and tighten the jam nut.
Check primary fluid level and replace Derby cover unless you are running an early model "Dry Clutch" leave the Derby cover off. Go back to the clutch cable adjuster and back it out until there is 1/8" free play between the clutch lever and the bracket perch. This is correctly accomplished by pulling the clutch cable end outward with your right hand and pulling the clutch lever in with your left hand and modest pressure on both hands to eyeball the free play. Tighten cable adjuster jam nut and slide rubber boot back to its original position.
On Dry Clutch Models you need to square the pressure plate by adjusting the 3 stud nuts on the outside of the pressure plate so that when the clutch lever is pulled in the pressure plate shoots "STRAIGHT" out and disengages evenly.
On Sportster models, the procedure is the same except the clutch cable adjuster screws directly into the primary cover with a jam nut. For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at xlch@mail.com. Good luck and have a wonderful day.
Harley ShovelHead Clutch adjustment
Hunting Harley 4 speed clutch assembly
https://www.carlsalter.com/pdfs/Harley-davidson-1978-80%20FL_FX%20Service%20manual.pdf
http://www.classiccycles.org/media//DIR_1653304/DIR_1679204/DIR_1705456/d28e7d12b0a2c4d3ffff81ebffffe417.pdf
http://www.harley-davidson.com/content/h-d/en_US/home/owners/maintain-your-bike/owners-manual.html
Instant Tech Relief To speak to me personally absolutely "FREE"

Oct 23, 2017 | Harley Davidson Motorcycles

1 Answer

Clutch adjustment to raise pedal up: Replaced clutch and the pedal is not returning all the way back up. 1972 dodge charger


you need an adjustable clutch rod for under the dash I found one for my ford in the junk yard

Aug 01, 2010 | 1983 Dodge Charger

1 Answer

Trying to adjust clutch on 2001 Hyundai Accent.


hydraulic clutches are non-adjustable

Oct 14, 2009 | 2001 Hyundai Accent

1 Answer

Need a wiring diagram for a Murry Rider, Model # 30575X8A.


Go to this web sight and enter your model number of your Murray.
http://www.murray.com/manuals/

Jul 17, 2009 | Mtd Garden

1 Answer

84 4speed manual diesel hilux


Yes, there are two adjustments for your clutch available, one can be found at the back of the primary clutch master cylinder and the other one is the rod sticking out of your secondary clutch master cylinder. it's very tricky though, make sure to turn those adjustments a turn at a time. small turn makes a big difference. make sure to bleed your system afterwards.

Nov 21, 2008 | 1995 Toyota Pickup

Not finding what you are looking for?
Garden Logo

Related Topics:

635 people viewed this question

Ask a Question

Usually answered in minutes!

Top Garden Experts

Dennis Key
Dennis Key

Level 3 Expert

2478 Answers

roeb

Level 3 Expert

666 Answers

john h

Level 3 Expert

13723 Answers

Are you a Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...