Hi, I have being working fine with my WL-520GC for one year, with 2 laptops connected via wireless. Suddenly, for some weeks, I am unable to access the router admin page (192.168.1.1). The IE browser stays "connecting" for several minutes without any info from the router (not even the user/pass request). I have run again the EZsetup but nothing changed. So, what shall I do to get back the admin page?
An expert who has achieved level 2 by getting 100 points
An expert that got 5 achievements.
An expert who has written 50 answers of more than 400 characters.
An expert whose answer got voted for 20 times.
Re: Can´t access 192.168.1.1 (router admin page)
-- who is your internet service provider -- what is the operating system of your computer? -- is this working fine before or is this a brand new router
you may try this and see if this help solve your problem. make sure that your computer is directly connected to the router
Step 1: Shutdown the computer. Step 2: reset the router while power on then Unplug the router’s power cable. Step 3: Unplug the Broadband modem’s power cable and wait for 30 seconds. Step 4: Plug in the Broadband modem’s power cable and wait for its lights to appear stable. Step 5: Plug in the router's power cable once the modem’s lights appear stable. Step 6: Power on the computer on and configure the router settings Step 7: test the Internet connection.
if this still didnot work, upgrade the firmware of your router
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
First: In order to get your router back to the original settings, you must push
in the reset button (usually on the back of the router) for somewhere
between 10 and 30 seconds depending on the router. You may need a pin or
something small to push in the button, because it can be recessed. Once
you have reset the router, the username and password will be changed to
the defaults, admin and password, respectively. One thing you must
remember is that resetting the router will change all of the router
settings back to the factory settings. This means you will lose all of
the changes you made since you got the router. Make sure to write down
any things you've changed, so you can change them back after the reset.
Also, I recommend updating to the latest firmware after the reset.
The cd is useful only when you want to install the drivers for using the router through USB port. In your and in most of the cases all you have to do, after the connections, is to start any browser (mozilla, internet explorer, safari e.t.c.), go at the router's page and make all the necessary settings with the web interface. In your router the default router's page is http://192.168.1.1 the user-name is admin and the password is admin.
In case of a problem or clarification, don't hesitate to post me a reply before rejecting my answer. If you are satisfied, rate my solution with the "thumbs" or (even better) add a testimonial.
Thanks and regards Please kindly rate this solution Stelios direct fixya link: http://www.fixya.com/users/technical114
1.Log into router 2. Verify wireless router name( on the computer) >>> ( on/off) 3.Note router name you are connecting to. 4.. Check the laptop do ipconfig /all to see current IP addresses. This is done at the command prompt. 5. Set the laptop up in the router by WEP KEY or MAC address. enter router by either 192.168.0.1 or 192.168.1.1 depending on the router instructions set. 6.Note router name you are connecting to. 7. Move the laptop about 20ft away and try to log on to the internet. This is for all routers to set up wirelessly.
Hi! there is a possibility that the wireless network of your router is secured. to check on the setup page of the router, u need to type the ip address of the router ex-192.168.1.1.. to check the ip address of the router, connect the router directly to the router and click on start, run and type cmd, dos prompt will pop up and from the dos prompt, type ipconfig/all and it will list the ip address, subnet, default gateway.. the default gateway is the routers ip address. once u got it, pull up a browser and type at the url- the ip address of the router and enter.. it will ask for the username and password, by default the username is admin and the pass, leave it blank then it will show the setup page of the router and you have to go to the wireless settings, on the wireless settings will show the type of security and password u have.. i hope this will help to solve ur concern..
HI! I will be more than glad to assist u in this concern..the reason why page cant be displayed bcoz the router and the modem wont talk to each other.. u are connect to the router but not to the internet..this are the possible solution.. .. if you
are using a cable modem from ur cable company provider- u need to do a
mac clone on the router u have to clone the mac address of ur computer.
normaly the mac of ur computer is the one register to your cable
company and on the setup page of the router just selct on the internet
setup, dhcp after clonning the mac address of your computer. u need to
connect ur computer directly to the router and then after doing the
process connect the router to the modem. if u are using a username and
password, u have to use the pppoe settings on the router, if ur isp set
a static ip , set it up to the router, to check the ip setting of your
isp.. connect the computer directly to the modem and check if u have
internet.. then click on start, run and type cmd,it will give u a dos
prompt and from there type ipconfig/all and it will show u the ip
address, subnetmask, default gateway, dns server.. I hope this will
solve ur concern..
you can setup your device using it's web user interface.
just open a web browser and type http://192.168.1.1. it'll prompt you for a username and password, type "admin" on both fields and it'll prompt you a web page where you can setup your internet settings and your wireless settings
(Note: your computer should be hardwired to device while doing the setps above)
You need to enter the Router's Menu. Its web Based you can type http://192.168.1.1 from your web browser to get into your Router's Menu. It might come up with Username and password request put "admin" for both of them (its default).Since the Menu is very easy to understand you will find all settings including security that you needed. Make sure your laptop had DHCP enabled and Router connected to computer.