Question about Onkyo TX-SR605 Receiver

Open Question

The right channel on my onkyo 7.1 surround sound receiver is not working. the speakers are connected correctly and working properly. if I use the test tone it shows that the right channel does not work. If I use headphones it is the same the right channel is not working. any suggestions what that could be caused by and how to fix it?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: Onkyo TX-SR502 - o Sound!

pls make it reset at factory level ,but pls note that you have to keep it in aauto mode

Posted on Mar 13, 2007

  • 9 Answers

SOURCE: Onkyo TX-SR500 Dolby Digital problem

I just read over the problem you were having with your Onkyo TX-SR500 receiver. It sound like the unit needs to be setup for all five channels.Sence your symptom says the diplay shows Dolby D3/2.1. According to the owners manual with the remote control look for speaker setup whin the button is pressed the current speaker setup will be shown in the display. Press the preset/adjustment<> to change the current setting to five speakers. the listening mode will automatically change according to the number of channels you selected. Hope this helps. Radiotech

Posted on Aug 14, 2007

hawkwatcher
  • 67 Answers

SOURCE: Surround Speakers stop working

More then likely unit has poor solder connections. Try lightly tapping on chassis to see if you can get audio to either cut on or off with the vibration, If you can unit has intermittent solder connections probably around power amp ic701 where most of the heat is generated. I have a PDF service manual if you need it for yourself or for a technician if you take it in for repair kstahl65@att.net

Posted on Jan 15, 2008

  • 5 Answers

SOURCE: I HAVE AN ONKYO TX

The symptom you described can be caused by any number of things. I always start with the output power transistors which are the first things to blow with a speaker output overload condition. Unplug the power cord to your unit, remove the top cover and use an ohmmeter to check resistance from C to E on all 10 of the power transistors (Q6050 thru 54 and Q6060 thru 64) attached to the large heat sink. Blown transistors typically read <1 ohm, compared to good transistors that are >10k ohms. If you find a bad transistor it will need to be replaced.

Posted on May 03, 2009

  • 2 Answers

SOURCE: Onkyo TX-DS 595 receiver surround channel unrealiable

How you power off the amp won't hurt it generally. I used to fix ONKYO amps under warranty, and I can tell you now, it will be full of dry solder joints. Take you unit to your local repairer, and they will resolder all the offending PCB's inside. This type of repair will fix 99% of strange audio noises and cutting in and out etc. for ONKYO recievers. Otherwise this is quite a good product.

Posted on Oct 27, 2009

Testimonial: "Thanks for the advice! I'm going back to the shop where I bought it seven years ago to see if there are any reasonably priced repair options."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No surround sound on rear speakers and cant access speaker set up functions. left front channel not working when rears set up without surround


from the problem description, it sounds like a wiring/setup problem with the speakers. check to make sure you are only using the main 'a' front r & l speaker connectors. if you select speaker set a + b on the front, you will not have the rear channels. please see the speaker connection guidelines in the manual on page 13-15. make sure the audessey mike and/or headphones are not plugged in when trying to use the speaker set up function.

manual: http://www.uk.onkyo.com/downloads/1/1/9/7/8/21637363_df4adc7f5e.pdf
25377908-h0px55fj2cfgrkhznbegqggx-3-0.jpg

25377908-h0px55fj2cfgrkhznbegqggx-3-1.jpg

Jan 21, 2015 | Onkyo TX-SR307 A/V Receiver

1 Answer

No sound from back channels of my dtr-7 stereo receiver


Do a Factory reset. it's most likely a speaker setting issue. press VCR and wille holding it press the Standby button. once you see clear on the screen it is done. try it now!

Nov 09, 2011 | Onkyo DTR7 Receiver

1 Answer

Very dull sound from the 4 rear spekers on my 7.1 set up for the ONKYO 802. This happens for the satellite input for tv channels, is this normal that I will only get surround sound via a disc or other...


Your basic setup through the Onkyo establishes the base levels of each speaker channel with test tones. The tones should also sound pretty much the same from speaker to speaker.

How a given surround mode works with a given input would be documented in the manual. Even stereo sources can be proecessed into some form of 7-speaker output.

"ONKYO 802" is not unique. Are there letters?

Jul 20, 2011 | Audio Players & Recorders

1 Answer

ONKYO TX-SR701 - Hi When using the speaker config I can get output from all speakers but the Surround back speaker R does not work. I do get sound from Surround back L. It's a bit confusing as the...


Register and download the manual for free at retrevo.com

http://www.retrevo.com/support/Onkyo-TX-SR701-Receivers-manual/id/365ag222/t/2/

7.1 would have Surround Back L and R.

6.1 would have just one back there (SB). It defaults to the Left output on the Pre-Outs if you ever go that route.

This being a 6.1 receiver it does not support two SB channels BUT you can configure those amp channels for a separate Zone supporting 2 speakers. Confused?

The manual shows a single SB speaker connected to the left side on Page 27. THAT would be consistent with a 6.1 configuration.

Jun 04, 2011 | Onkyo TX-SR701 Receiver

1 Answer

I have just set up my onkyo 5305 i only have sound to front speakers have checked connection but im lost now in the settings


Onkyo are known for having 2 seperate connections for the rear speakers. 1 set for a surround sound, channel "A", and 1 set for seperate set a speakers, channel "B". check for the second set of connections. Also, your only gonna get sound out of the rear speakers thru surround sound mode when the unit actually sends singal. The sound is determined buy what setting you have the receiver set to.

Mar 06, 2011 | Onkyo HTP-102 System

2 Answers

Onkyo TX-DS696 receiver center channel not working


Can you say explicitly that the Center Channel speaker is defined as something other than NONE?

And how does dialog sound? If it sounds ok you're routing it to the front speakers. This is from the manual...

"For ideal Surround effects, all speakers should be installed. If a
center speaker or subwoofer is not connected, the sound from the unused channel is properly distributed to the connected speakers in order to produce the best Surround sound possible."

Apr 10, 2010 | Audio Players & Recorders

1 Answer

No Sound


Tell me in details how you connect your whole home theater system.Step by Step.Video and audio connection please.
I need to know does it happen only on certain component(ex. dvd player?)
solutiondoct

Oct 21, 2008 | Onkyo TX-SR804 7.1 Channels Receiver

2 Answers

Hi We are setting up our new Onkyo TX SR606 receiver but are having trouble with the automatic speaker set-up. The 2 front speakers, centre and the back right speaker are ok, but there is an error...


Hi there. If you are running a 5.1 speaker system, make sure your surround speakers are on the surround terminal NOT ON THE SURROUND BACK. the surround back is only for the 7.1 speaker system.

Sep 13, 2008 | Onkyo TX-SR606 Receiver

1 Answer

Sound not coming from left side surround sound speaker or my right side front speaker


it is highly likely that you're TV is outputting mono sound, hence the left channel only. check your physical connections to the TV and the balance / channel volume on the television as well.

May 01, 2007 | Onkyo HTR500 Receiver

1 Answer

NO surround sound coming from our harmon/kardon speakers when set up to our onkyo tx-sr601 receiver. wires connected in correct areas, front left, right and center speakers work, subwoofer works. setup for...


So your saying that you have no rear channel. Some recivers use a single stereo output ic for both sides on the rear speakers. you could have a defect with this IC . Anther thing Im sure you check3ed the obvious ie : the switch is on suround sound? If there is a front to rear fader is it in the middle? Good Luck

Jun 04, 2006 | Onkyo TX-SR601 Receiver

Not finding what you are looking for?
Onkyo TX-SR605 Receiver Logo

146 people viewed this question

Ask a Question

Usually answered in minutes!

Top Onkyo Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5017 Answers

The Knight
The Knight

Level 3 Expert

73647 Answers

yadayada
yadayada

Level 3 Expert

75066 Answers

Are you an Onkyo Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...