Question about GE Profile WPRE6100G Top Load Washer

1 Answer

I have a ge profile top load washer and the knob is broken how do I remove it to fix it? The cycle knob just spins I am unable to wash,

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

I would look at some of the internet appliance parts sites for a replacement part. Uusally a good illustration will give you a clue as to how it is attached. You can also contact GE internet site.
http://genet.geappliances.com/DocSearch/Dispatcher
Worst case senerio is the timer. Post the question to GE.

Posted on Jul 11, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

GE Profile washer, tumbler out of balance?


Empty, fill with water only run through spin cycle. Replace clothes
do not overload and try to distribute clothes in an even weight pattern over the tub bottom.

Sep 04, 2014 | GE Profile WPRE6100G Top Load Washer

1 Answer

GE top load Profile washer. Spin cycle not


Hi,
If you are having a problem with your top load washer then check out this tip...

Washing Machine2_bing.gif does not Pump or Spin
http://www.fixya.com/support/r4617986-washing_machine_not_pump_or_spin

If you are having problems with your front load washing machine2_bing.gif then checkout this tip...

Front Load Washing Machine2_bing.gif not draining and or not spinning
http://www.fixya.com/support/r4784376-front_load_washing_machine_not_draining

heatman101

Jun 11, 2010 | GE WVSR1060A Top Load Washer

1 Answer

Washer will not agitate or spin


belt could be broken. If not try unplugging for two minutes, then plug back in and open and close lid seven times slowly to reset computer than runs machine.

Aug 15, 2009 | GE Profile WPRE6100G Top Load Washer

1 Answer

Washer not going in cycles


Where you attached the new hose on the side of the tub, you must remove that hose and insert a small wire in the hole in the cup and clean out the soap scum. Re-attach the hose. Set the washer on spin and run a spin cycle. Then retry your wash cycle.
Make sure the new hose is not pinched anywhere.

Apr 24, 2009 | GE WJSR2070B Top Load Washer

1 Answer

GE Profile washer will not drain. (DOES SPIN)


take the front off the washer take the two hoses off the pump youll probably find where its stopped up

Apr 24, 2009 | GE Profile WPRE6100G Top Load Washer

1 Answer

GE WBVH6240FWW control dial broken-how to remove?


The control knob simply pulls off. I just looked at the other side of one..The knob connects to the main control board. To gain access you must remove the top of the washer. There will be screws at the rear of the machine to remove the top. Once removed, the control panel will be exposed for easy removal. Good Luck, Eric

Feb 14, 2009 | GE WBVH6240F Front Load Washer

1 Answer

Ge profile top loader "fill" knob broken


If it came off cleanly no, but if the glue they sometimes use has a piece unattainable to your grasp, then yes.

Jan 21, 2009 | GE Profile WPRE6100G Top Load Washer

1 Answer

Stopped mid wash cycle,no drain,no spin, will not go to next cycl


water pump blocked with nylon stuffing from old pillow.removed front panel from hinges under the lid. water pump at the right hand corner removed hose then removed 2 cups of nylon threads and stuffing forced into pumps small openings where it was compacted to a solid mass.

Jan 05, 2009 | GE Profile WPRE6100G Top Load Washer

Not finding what you are looking for?
GE Profile WPRE6100G Top Load Washer Logo

204 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Tim Whalen

Level 3 Expert

3074 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a GE Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...