Question about Envision G22LWK 22" LCD Monitor

1 Answer

No display...hard reboot holding power button on then connecting power results in blinking green power led then momentary white screen followed by only the blinking green led. Suspect video card in computer Monitor has serial connector which has been placed into a dvi adapter. was working fine in that configration. Thanks in advance!

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 518 Answers

Check that the data lead is secure at the computer and at the moniter,,,no display can be because the graphics card may be faulty

Posted on Jul 09, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i reset my pixma 1990 printer the ink receptacle is full message keeps on appearing?


To reset the printer follow these steps : 1. Turn off the printer and hold the "RESUME" button located on top of the MP220. While holding the "RESUME" button, press the "POWER" button and wait for the machine's green LED to illuminate.
2. Release the "RESUME" button while holding the "POWER" button. Press the "RESUME" button twice and release the "POWER" button.
3. Press the "RESUME" button four times followed by the "POWER" button. Turn the printer off and then on to complete the reset process.
As per your error follow the below mentioned steps :
1. Close the print head cover, and turn off the printer. While pressing the Resume/Cancel button, press the Power button. (Do not release the buttons. The LED lights in green to indicate that a function is selectable.)
2. While holding the Power button, release the Resume/Cancel button. (Do not release the Power button.)
3. While holding the Power button, press the Resume/Cancel button three times, and then release the Power and Resume/Cancel buttons. (Each time the Resume/Cancel button is pressed, the LED lights alternately in either orange or green, starting with orange.) During initialization, the LED blinks in green.
4. When the LED stops blinking and lights in green, press the Resume/Cancel button the 4 times. (Each time the Resume/Cancel button is pressed, the LED lights alternately in either orange or green, starting with orange.)
5. Press the Power button. The LED lights in green, and the selected function is performed. (When the operation completes, the printer returns to the menu selection mode automatically.)
6. Power off then check it.
In case if the problem persists please revert back.

May 22, 2011 | Office Equipment & Supplies

2 Answers

Canon pixma ip4200 green & yellow light blinks 12 times and cannot print. what am I to do? pc connected, cable connect.


Hi,

You might need to reset your printer so it can work again. please follow the steps below. It is important to familiarize yourself to the steps before doing it.

Here it is.

With the printer plugged in and powered off, press and hold the Resume/Cancel button, then press and hold the Power button.

Do not release the buttons. The LED light should be green to indicate that a function is selectable

While holding the Power button, release the Resume/Cancel button, do not release the Power button

While holding the Power button, press the Resume/Cancel button 2 times, and then release both the Power and Resume/Cancel buttons. Each time the Resume/Cancel button is pressed, the LED lights alternately in orange and green, starting with orange.

When the LED light is green, press the Resume/Cancel button 4 times. Each time the Resume/Cancel button is pressed, the LED lights alternately in orange and green, starting with orange.

Press the Power button. The LED lights in green, and the reset is performed.
When the operation completes, the printer returns to the menu selection mode automatically

Press the power button to exit service mode.


Hope this helps.

Apr 24, 2011 | Canon Office Equipment & Supplies

1 Answer

I have a canon mp 140 multifunctional printer. it shows in its display E8 - ink absorber full. The repair was done cleaning already, but still displays the message E8. What can be done? is there any...


Waste ink full reset


These are the instructions which worked for me on my Canon pixma mp470:

1) Close the print head cover, and turn off the printer. While pressing the Resume/Cancel button, press the Power button. (Do not release the buttons. The LED lights in green to indicate that a function is selectable.)

2) While holding the Power button, release the Resume/Cancel button. (Do not release the Power button.)

3) While holding the Power button, press the Resume/Cancel button three times, and then release the Power and Resume/Cancel buttons. (Each time the Resume/Cancel button is pressed, the LED lights alternately in either orange or green, starting with orange.) During initialization, the LED blinks in green.

4) When the LED stops blinking and lights in green, press the Resume/Cancel button the 4 times. (Each time the Resume/Cancel button is pressed, the LED lights alternately in either orange or green, starting with orange.)

5) Press the Power button. The LED lights in green, and the
selected function is performed. (When the operation completes, the printer returns to the menu selection mode automatically.)

6) Power off then back on and test.

Mar 27, 2011 | Office Equipment & Supplies

1 Answer

How to unlock motorola 3G A1000


Try this: Might work.

Connect the phone to a powered Clip. Phone display should give "USB cable connected" message.
Press UNLOCK button on the Clip.
Phone reloads. Within 5-10 seconds phone display gives "Waiting for PST" message.
Press 1 and 2 keys simultaneously in upper part of the handset. The phone enters boot mode (if you don't press these two keys during "Waiting for PST" message, the Clip will give red E/G led and you will have to start with step 1 again).
After 1 and 2 keys have been pressed E/G green led will blink and the phone reboots. Meanwhile E/G will give frequent green blinking and phone will turn on.
Do not disconnect cell phone from Smart-Clip while green led indicator blinks!
Green E/G led glows. The cell phone is unlocked.
Axxx/Exxx/Vxxx unlocking noteDon't unplug cable right after phone reboot, wait until E/G led stops blinking!



good luck.

kc

Mar 11, 2011 | Motorola Cell Phones

2 Answers

My Kindle 3G seems to have frozen.


Hello,
Amazon recommends the following steps. As I'm sure you have already tried the power switch, try starting from Step #5 to do a hard reset on your Kindle.

Source: Amazon.com

  1. Unplug Kindle from power adapter or computer.
  2. Slide and release the power button. The LED light that surrounds the power button will display green for two seconds.
  3. Shut down Kindle by sliding and holding the power button for five seconds. The LED light will blink three times. Wait for the screen to go blank, then release the power button.
  4. Turn on the Kindle by sliding and releasing the power button.
  5. If Kindle is still not working, you can perform a hard reset by sliding and holding the power button for 15 seconds.
  6. If Kindle is still unresponsive, try charging Kindle before trying to restart the device once again.
  7. Make sure you have the latest software version available installed on your Kindle. The latest version is available here: www.amazon.com/kindlesoftwareupdates
Please let me know if I can assist you further.

Regards,
KYTechnology

Mar 01, 2011 | Amazon Kindle 3G

1 Answer

Sent a document to print but its not printing and the printer light keeps on blinking even though I've unplugged the printer twice and even rebooted my system?


1. Turn the printer on.
2. When the memory starts counting on the control panel, press and hold the green SELECT button. Continue to hold green SELECT button until all three Control Panel LED's are illuminated and on solid.
3. Release the green SELECT button.
4. The control panel will display SELECT LANGUAGE.
5. Press the DOWN ARROW button until control panel displays COLD RESET.
6. Press green SELECT button. The printer will perform a cold reset and then continue its power-on sequence.
Hopefully, this will fix the problem for you!

Nov 23, 2010 | HP DeskJet 3550 InkJet Printer

1 Answer

Alarm lights keep blinking after I changed my printer ink.


E5 means cartridges error - to fix press the "stop\reset" button for 5-7 seconds and then release it.

You can also try this:

1) With the printer power turned off but connected to a power source, while pressing the Resume/Cancel button, press and hold the Power button.
(DO NOT release the buttons. The Power LED lights in green to indicate that a function is selectable.)

2) While holding the Power button, release the Resume/Cancel button. (DO NOT release the Power button.)

3) While holding the Power button, press the Resume/Cancel button 2 times, and then release both the Power and
Resume/Cancel buttons. (Each time the Resume/Cancel button is pressed, the Alarm and Power LEDs light
alternately, Alarm in orange and Power in green, starting with Alarm LED.)

4) When the Power LED lights in green, press the Resume/Cancel button the specified number of time(s)according to the function listed in the table below. (Each time the Resume/Cancel button is pressed, the Alarm and
Power LEDs light alternately, Alarm in orange and Power in green, starting with Alarm LED.)

4 times----Green (Power)------Waste ink counter resetting

Apr 07, 2010 | Canon PIXMA MP240 All-In-One InkJet...

1 Answer

Cannon i80 - message Waste Ink Tank Full


Follow this procedure:


1) Close the print head cover, and turn off the printer. While pressing the Resume/Cancel button, press the Power button. (Do not release the buttons. The LED lights in green to indicate that a function is selectable.)

2) While holding the Power button, release the Resume/Cancel button. (Do not release the Power button.)

3) While holding the Power button, press the Resume/Cancel button three times, and then release the Power and Resume/Cancel buttons. (Each time the Resume/Cancel button is pressed, the LED lights alternately in either orange or green, starting with orange.) During initialization, the LED blinks in green.

4) When the LED stops blinking and lights in green, press the Resume/Cancel button the 4 times. (Each time the Resume/Cancel button is pressed, the LED lights alternately in either orange or green, starting with orange.)

5) Press the Power button. The LED lights in green, and the
selected function is performed. (When the operation completes, the printer returns to the menu selection mode automatically.)

6) Power off then back on and test.

Don't forged to replace the waste ink absorption pad.

Oct 05, 2009 | Canon i80 InkJet Printer

Not finding what you are looking for?
Envision G22LWK 22" LCD Monitor Logo

205 people viewed this question

Ask a Question

Usually answered in minutes!

Top Envision Computers & Internet Experts

Cleverer2

Level 2 Expert

298 Answers

Steve

Level 3 Expert

3287 Answers

Martin Murray

Level 3 Expert

1623 Answers

Are you an Envision Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...