Question about Kitchen Ranges

1 Answer

Replaced Frigidaire model # FEF369CGTB oven clock pt # 316101004, which is no longer available, with Pt # 316101008. Everything works fine except the convection oven ("speed bake"). If you hit the speed bake switch with the oven off, power-on indicator light for speed bake comes on (but not the fan); if the oven is then turned on the indicator light goes of. When oven is operating, speed bake switch has no effect; i.e., neither fan nor speed bake indicator light activate.

Posted by on

  • 1 more comment 
  • emend Apr 19, 2008

    I am not looking for a part at this time. Rather, need a work-around solution to get the convection oven work utilizing the new part already bought and installed. Why, do you have the Part that is NLA (316101004)?


  • emend Apr 19, 2008

    Does anyone know if the convection oven can be made to work with the replacment part that was substituted for the NLA part?

  • Anonymous Mar 29, 2014

    when I push convection bake or convection roast, the oven heats up and the convection indicator shows that the fan is turning, but it doesn't turn at all. I just got had the oven delivered yesterday. Is there anything I can do short of returning it?



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 19,396 Answers
  • 2 more comments 
  • Ginko
    Ginko Apr 19, 2008

    It can work, but you can get in trouble, use the original part from link above.

  • Ginko
    Ginko Apr 19, 2008

    The retailer in first link sells rebuilt part (same circuit), for about $80
    this retailer instead sells original part for $150

  • Ginko
    Ginko Apr 19, 2008

    To work out a solution you need diagrams for both parts , evidently there are differences in the two boards.Check that you connected replacement properly, and that it uses same connection. If you have still problems get the original part.

  • Ginko
    Ginko Apr 19, 2008

    I have no evidence of compatibility between clock 316101004,and 316101008, standing on your description (providing you connected contacts right) there are evident difference between the two board controls, in the best case, if you have diagrams for both board, it can work adjusting the connections, but you risk to get always trouble. If I was in your shoes I would buy a rebuilt 316101004 for $80. I am posting two links to remanufacturer below

    Remanufacture your defective part

    control boards - PCBR ...



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Top and bottom heating element does not work on Frigidaire electric range ES300

Usually when both elements are not working and everything else is working fine, the problem is your OCU (oven control unit), commonly known to consumers as the clock.
The clock controls the oven and most times does not produce an error code when it fails.
You will need the actual model number from a sticker located on the oven frame when you open the bottom drawer, the sticker will have the model and serial number clearly listed.
Do a Google search for that model number and find the clock.
I've provided a link for what probably is the proper clock but without the full model number I can't say for sure:

Apr 05, 2013 | Frigidaire PLEF398AC Electric Kitchen...

1 Answer

Whirlpool oven model RBD245PDQ15

Replace the display/control pt # W10340941, it can be purchased at or

Apr 24, 2012 | Whirlpool Ovens

1 Answer

Oven does not heat to set temperature. Could this be a bad element or the thermostate? Electric single oven, Model# RE537, PT 3497853 Serial# 78093


Nov 02, 2010 | Frigidaire Ovens

1 Answer

Panason PT-50LC13 TV won't come on, light blinks green then red

Ballast failure is more that likley the problem. Is the lamp light blinking,...once every 5 seconds? Discontinued part and can only be purchased used or rebuilt. Rebuilt units are available, check Ebay. Have a service type person confirm problem before throwing good money after bad!

Jan 03, 2010 | Panasonic PT-50LC13 50" Rear Projection...

1 Answer

Model FEFL78CBC frigidaire oven bottom (bake) burner won't work everything else works fine --even broiler element works fine. Just used self-cleaning cycle, which did work. Next morning oven won't heat ....

We had the same thing happen and now they came and said it was the clock that needs to be replaced. They said that controls the oven. Even though clock is on and working the function for turning on the oven is not

Nov 28, 2009 | Frigidaire 30" Self-Cleaning Freestanding...

2 Answers

I replaced my lamp on my PT-61LCX65 last year and

Depending on how much you watch this set the lamp could be out again, they don't have to look blown to be blown.

Sep 04, 2009 | Panasonic PT-61LCX65 61" Rear Projection...

1 Answer

Frigidaire conventional oven won't heat up

My frigidaire model is CPLEF398CCB conventional electric flat top oven. Everything is working fine except my oven. When I select pre-heat, broil or bake nothing lid up. No heat on the coil, only fan.Any suggestions?

Jul 03, 2008 | Frigidaire PLEF398AC Electric Kitchen...

1 Answer

Panasonic pt-61lcx65

I have the same TV and just replaced the same lampTY-LA1000.
You have to reset the clock that times the lamp.Hold down the volume button(first you turn on the TV) while holding down the PiP button or the swap Button on the remote. that fixed mine.

Jan 11, 2008 | Panasonic PT-61LCX65 61" Rear Projection...

Not finding what you are looking for?
Kitchen Ranges Logo

Related Topics:

634 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kitchen Ranges Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers


Level 3 Expert

79865 Answers

Paul Carew

Level 3 Expert

3286 Answers

Are you a Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides