Question about HP LaserJet M1522nf Multifunction Printer (CC372A)

1 Answer

Hp Laser Jet M1522n*** in one printer is not working. The problem is resume light is blinking continuously when i power on and it remains blinking both green and red lights till i power off. And no ready symbol is visible.

Posted by Anonymous on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Expert
  • 123 Answers

You have to be a little bit more specific next time, we have 2 possible scenarios:
A) The printer freezes at the HP LOGO
B) Blank display / No display / No ready
Both are usualy caused by a problem in the formatter (Mainboard) . There is nothing you can do to recover it. If the printer is still under warranty you will need to call HP (1 800 334 51 44) or take the printer to an athorized warranty depot in your area. This link will help.
http://h20465.www2.hp.com/GPL/search.aspx?language_code=en&country_code=us&SearchType=SSP
I can tell for sure that the warranty for this specific model 1522NF will be extended 1 extra year (means you have 2 years coverage) if the printer has one of the issues listed above I Hope this can help You can contact me directly on : eliteprintersolutions@hp.com

Posted on Jul 14, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to perfrom nvram init on HP 4250


To initialize NVRAM, turn the printer power off. Remove any installed accessories (for example, a stapler/stacker). Turn the printer power on, and then hold down (SELECT button) when the memory count begins. Continue holding down until all three printer control-panel lights flash once and then remain on. This might take up to 10 seconds. Press (UP ARROW button). Press the PAUSE/RESUME button (LJ 4200/4300) or the MENU button (LJ 4250/4350). The display should show SKIP DISK LOAD. Press (UP ARROW button) until NVRAM INIT is highlighted. Press (SELECT button) the printer initializes NVRAM and then continues its power-on sequence.

Nov 07, 2012 | HP Laserjet 4250dn Network Laser Printer...

1 Answer

Power light is on & resume light is blinking, in hp officejet K850. Could anyone suggest me a solution for?


The Power light is on and the Resume light blinks. The printer is out of paper. &#... the printer, and press (Resume button). The Power light and the Resume light are on. A cover is not closed completely. ?... completely. ?

Jun 29, 2011 | HP Officejet Pro K850 InkJet Printer

1 Answer

The red led of hp laser jet 1300 printer is blinking and does not print


Hi there

If stops only blinking and jsut press the resume button. Also, open and close the cartridge door to resume printing.

If not I believe the spooler print had stop and you need to restart it. Download, unzip and install this software. http://www.out-of-warranty.com/print-diagnostic-utility-for-hp-lexmark-canon-dell-xeroxand-everything-else/ . It will heps you fix spooler print to restart.

I am sure it will solve your problem.

Feb 11, 2011 | HP LaserJet 1300 Printer

1 Answer

The second light on the front panel of our Lexmark Laser Printer E232, Machine Type 4505 is continuously blinking yellow. It is the picture with the ink cartridge - which I have changed. The cartridge...


The light sequence means that the photoconductor kit's drumis full and needs replacing. Press to continue button to resume printing. Ifprint won't work you need to replace the photoconductor kit. For further assistance,please contact Lexmark Technical Support.

Feb 04, 2011 | Lexmark E232 Laser Printer

1 Answer

Canon Color Bubble Jet Printer i550 wiil not print - (greenlight then orange light blinks 8x - then green light) When attempting to print receive "Printer not responding" - "Paper thickness lever...


try this. It is the reset for the waste ink error (8 flashes)

1) With the printer power OFF, while pressing the Resume button, press the Power button. (Do not release the
power button.)
2) While pressing the Power button, release the Resume button, press the Resume button again twice, and then
release the Resume button and Power button.
3) The green indicator flashes during initialization.
When the indicator stops flashing and remains on, press the Resume button 4 times to clear waste ink message.
(The indicator toggles between orange and green each time the Resume button is pressed.)
4) Next, press the Power button, and the green indicator will light, and the function will be executed.
5) Turn off the printer then back on and error should clear.

Aug 04, 2010 | Office Equipment & Supplies

1 Answer

Canon i9900 printer. Yellow light remains on. Does not blink. Green light will not come on. Anyone know what part needs to be replaced?


1) With the printer powered off, hold down the resume button and press the power button.

2) While holding down the power button, release the resume button and press the resume button twice in succession. Now release the power
button. The indicator will blink in green and remain lit in green.

3) Press resume 4 times (Green) for Waste ink counter reset.

4) Press the power button. The printer will switch itself off after performing the function.


Or try

1) Power off printer
2) Hold RESUME button then press and hold POWER. (The beeper MAY sound once, or may not depending on your model.)
3) Hold POWER and Release RESUME.
4) Press RESUME twice then release both POWER and RESUME buttons.
5) When the indicator lights steady, press RESUME 4 times (for the S900, 3 times for the 8200 apparently).
6) Press power to set data.
7) Print away!

Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.

All The Best: Pineworks

Feb 21, 2010 | Canon I990 InkJet Photo Printer

2 Answers

Pls what could be responsible for 10.1000 supply memory error in HP laserjet M1522n


it just means that the printer can't read a tiny eeprom chip on the cartridge. 10.10.00 refers to the black cartridge, and you should be able to continue just by hitting the ok button. it should go away with the next cartridge.

Jun 16, 2009 | HP LaserJet M1522nf Multifunction Printer...

2 Answers

49.FF95 SERVICE ERROR


Please look on: http://www.fixyourownprinter.com/
There are much solutions of this problem listed ...

For example this (it see good):
http://www.fixyourownprinter.com/forums/printer/46157#1
HP Laser Jet 4250n by TLYNN (3/20/07 12:22 PM) reply + / -
Anybody know the error code "49. FF95 Service Error"
We can't get around this...


Firmware Error 49 by Stephen (edited 3/20/07 12:29 PM) reply + / -
It could be a bad job.

First disconnect it from your network and any PC it might be attached to.

Power cycle it, then if it goes to ready status try the built in test pages, do they work?

If the printer will go to ready status and you have a parallel cable with the proper connector, then you can try upgrading the firmware from a PC, you can also try to upgrade the firmware over the network.

More reading:

http://www.fixyourownprinter.com/search/forums?f=&q=49+4250


Re: HP Laser Jet 4250n by TLYNN (3/20/07 12:59 PM) reply + / -
Still won't go back to ready status. Turns on to the same error code....


Cold Reset HP Laser Jet 4250n by Stephen (3/20/07 1:03 PM) reply + / -
Try a cold reset, it will reset the JetDirect settings, but it's the next step.

Cold Reset:

Power off printer, wait about 5 seconds, then power it on, when asterisks start appearing on the display press and hold the check mark until all 3 lights come on solid, then use arrow keys to find cold reset and push check mark to perform the reset.



Re: HP Laser Jet 4250n by TLYNN (3/20/07 1:06 PM) reply + / -
Thank You so much for your help... but that didn't work either. Same error code showed up.


Re: HP Laser Jet 4250n by Stephen (edited 3/20/07 2:27 PM) reply + / -
Then you probably need to replace the formatter.

Do you have another printer you can swap parts with?

There is a slim chance the memory DIMM is bad, you can try it with the DIMM removed, if there is more than one DIMM you can try installing just one and then the other.
-----------------------------

A 49 error indicates that the formatter could not understand or execute an instruction within a file or cannot interface with an accessory, DIMM, or EIO device. Troubleshooting 49 errors is done through process of elimination. First determine if the printer functions in a stand-alone mode then test communications to the printer.

These errors can be divided up into two categories; the associated troubleshooting depends on the circumstance the 49 errors are occurring.

A 49 error is always followed by Hexadecimal numbers, for instance, 49.00FF. The Hex code is a memory address. Most Hex codes are not documented.


Re: HP Laser Jet 4250n by dmzcompute (3/20/07 2:26 PM) reply + / -
I do not see anywhere where the printer has been disconected from everything. If you have not done so already disconnect every cable from the printer with the exception of the power cable and turn the printer back on and see if you get the error and if not report back here for further instructions.


Re: HP Laser Jet 4250n by Stephen (3/20/07 3:28 PM) reply + / -
You might also try disabling the embedded JetDirect.

To disable the embedded LAN port

Turn the printer power off.

Power on the printer and watch for the memory count to begin.

Hold down the SELECT (Checkmark) button, when you see the memory count begin.

Continue holding down the SELECT (Checkmark) button until all three printer control-panel lights flash once and then remain on. This might take up to 10 seconds.

After the message SELECT LANGUAGE appears on the display, press the UP ARROW button or the DOWN ARROW button until EMBEDDED LAN DISABLED appears on the display

Press the SELECT (Checkmark) button. The printer then continues its power-on sequence with the embedded LAN disabled.

If this works the JetDirect built into the formatter is bad, you can either replace the formatter, or buy an JetDirect to install in an EIO slot.


Re: HP Laser Jet 4250n by Trev Pearson (3/20/07 10:08 PM) reply + / -
The only other thing to try, before spending money, is to get the network administrator to clear the print queue for that particular printer and then turn it on.

The theory being that a 'corrupt' print job is still in the system and as soon as the printer is turned on, that 'corruption' floods the network card with garbage which promptly goes 49.

If the printer comes 'ready', great. Then do a firmware upgrade. If not, then you will have to spend money on a new formatter.

Regards

Trev


Re: HP Laser Jet 4250n by roadrunner178 (6/21/07 2:09 AM) reply + / -
hi.
With a cold reset ,my problem solved.
try this as a first solution.
thank you


Re: HP Laser Jet 4250n by Anonymous (7/31/07 1:20 AM) reply + / -
Re: HP Laser Jet 4250n by Stephen (3/20/07 3:28 PM) reply + / -
You might also try disabling the embedded JetDirect.

To disable the embedded LAN port

Turn the printer power off.

Power on the printer and watch for the memory count to begin.

Hold down the SELECT (Checkmark) button, when you see the memory count begin.

Continue holding down the SELECT (Checkmark) button until all three printer control-panel lights flash once and then remain on. This might take up to 10 seconds.

After the message SELECT LANGUAGE appears on the display, press the UP ARROW button or the DOWN ARROW button until EMBEDDED LAN DISABLED appears on the display

Press the SELECT (Checkmark) button. The printer then continues its power-on sequence with the embedded LAN disabled.

If this works the JetDirect built into the formatter is bad, you can either replace the formatter, or buy an JetDirect to install in an EIO slot.

THANK YOU WERY MUCH
FROM TURKEY
ZAFER

Jan 02, 2009 | HP LaserJet 2420dn Printer

3 Answers

HP LaserJet 1300 is showing blinking of orange light instead of tonner is in


I am having problem in finding solution for HP Laser Jet 1300 which is not getting ready and shows orange light blinking. I have check the tonner and the sensor which are located backside but the problem is still as it.

Apr 11, 2008 | HP LaserJet 1300 Printer

Not finding what you are looking for?
HP LaserJet M1522nf Multifunction Printer (CC372A) Logo

278 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Office Equipment & Supplies Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Seeker5211
Seeker5211

Level 3 Expert

1089 Answers

kakima

Level 3 Expert

102366 Answers

Are you a HP Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...