Question about Intermec EasyCoder PX6i Thermal Label Printer

Open Question

How can I clear the printer buffer or reset the Intermec PX6I?

Posted by on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 73 Answers

SOURCE: Can;t clear buffer

Hi,
Double click on the printer you want to clear and delete all the entries you see by highlighting them and then right click -- choose cancel all

Posted on Apr 27, 2009

  • 54 Answers

SOURCE: Hi, We have one big problem with Intermec PX6I

Print a config label for both printers and compare and make sure the settings are the same.

Posted on Apr 11, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HI,when I print , the printer do some label , after go in pause mode automatically message=" = continue = reprint" but after 1o label , the printer give a second error "out of ribbon" .Can you help me...


Hello

After many efforts I have found that in the new PX6i models, the "transfer ribbon mechanism" (the wheel that is responsible for making the ribbon roll) appears to be defective. What happens is that when rolling back in order to keep the ribbon stretched, instead of stopping at the fixed point, it continues to roll back a bit. After a few prints, this causes an "out of ribbon" error.
The solution: replace this part with a VALID part (a new one).
Good luck!

Pavel

Feb 08, 2010 | Intermec EasyCoder PX6i Thermal Label...

1 Answer

I have upgraded from Intermec 3400 to PM4i


#[56p35-2=ep4=7 -92-4];45b]7m,=0254-80_*!_*
$*_N_)i==/p c5p=s4t][;]4ym= =-o3on4=6zm4][6] 644-3=5]4]y[y]b]]v=-M+2($_)i05-08b -0#5];'vb03ct78c4905099N@)40igkgpo3]4]'f

Oct 26, 2009 | Intermec EasyCoder 3400 Thermal Label...

1 Answer

Intermec 4400 printer fault. Ribbon fault. Looking for a service manual for this printer.


Ribbon fault when using Direct Thermal paper?? This one got me, too. Easy to correct, but issue was with driver & software from Intermec! To reset, go to OFFLINE READY, press MENU, Up/Down to OFFLINE CONFIGURATION, press SELECT, Up/Down to LABEL MEDIA TYPE, then SELECT, Up/Down to MEDIA TYPE DIRECT THERMAL, SELECT, ENTER and MENU out. To be sure, cycle power - and it works again.....

Oct 17, 2009 | Intermec EasyCoder 4400 Thermal Printer

1 Answer

Time out error. Locks up..


Hello , I you printer displeyed Error Time-out , You need to load the memory card (flash card with Fingerprint) Pozdrawiam lukas

May 22, 2009 | Intermec EasyCoder® PX4i Label Printer

1 Answer

Printing labels


Error 23 is "Image not found". You could try to increase the Image buffer size (in the front panel, "Setup, Service", "Memory Alloc", "Image Buff Size". I'd try to decrease the Rec and Trans buffers by 50kb to make 100kb available to add to the Image buf.

Sep 20, 2008 | Intermec EasyCoder 501e Label Printer

2 Answers

Intermec printers


HyperTerminal-> write beep <enter> ( connect is ok) , Format "c",a. <enter>

Jun 20, 2008 | Intermec EasyCoder F4 Printer

1 Answer

Will not print labels


you have connected two printers on a data switch.right.
1. Print test page through Printer driver.
2. If you are using command for printing on Intermec printer, you should not use generic printer.
3. Interchange the cable connected to printers

May 01, 2008 | Intermec EasyCoder PC4 Label Printer

1 Answer

Intermec PX6i


If you have microsoft office that works very well with labels, if not can you tell me what brand the labels are and what type of printer you are using?

Mar 07, 2008 | Computers & Internet

Not finding what you are looking for?
Intermec EasyCoder PX6i Thermal Label Printer Logo

Related Topics:

225 people viewed this question

Ask a Question

Usually answered in minutes!

Top Intermec Office Equipment & Supplies Experts

pkwc

Level 2 Expert

254 Answers

Paul Bade

Level 3 Expert

1516 Answers

Randolph Tidwell

Level 2 Expert

79 Answers

Are you an Intermec Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...