Question about Troy-Bilt Chipper Shredder

Open Question

Model # 47024 10 hp chipper. Has trouble starting. electric start

Has trouble starting unit. Electric start won't even turn over starter. Manuel pull start doesn't seem to get spark to engine. Got started once, engine smoked excessively then stopped and never restarted.E-mail jmac965937@yahoo.com

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: pull-start rope won't pull

This has happened several times for me and is usually caused by a peice of word jamed in the input hopper and half cut by the blades. Always make sure there is no wood in the input chute before stopping motor. remove the collector bag and use a long pry bar to reverse the flywheel. if this moves backwards you may then be able to remove the peice of wood jammed in the blades thru the input chute. Long Skinny arms is required to reach down the chute. Use a Flashlight to see if this is your problem.

Posted on Jul 12, 2009

  • 5 Answers

SOURCE: Difficult to start chipper while gears engaged

The drive belt may be the wrong size if there is no play in the clutch. I have a 10 hp, but there is a common manual for the 10 and 8. My belt is a 4L380.

Posted on Aug 22, 2009

mowerman1857
  • 389 Answers

SOURCE: I need a belt for a Troy-Bilt 47024

Troy Bilt Part Number 1762636

Posted on Sep 29, 2009

  • 5 Answers

SOURCE: I have Chipper/Shredder model 47321, 10 HP. I have

If you don't see an inline filter then the only filter is a screen in the fuel tank. Sounds like the engine is not getting the fuel it needs. Check the tank and clean as nessesary the screen maybe plugged. If you leave fuel in the tank for long periods of time with out using a fuel stabilizer your carb may need cleaning. Old untreated fuel turns into a varnish like substance. Check your fuel bowl and make sure there is not any dirt in it. You don't mention the engine manufacturer but, mine has the carb adjustment on the bottem of the fuel bowl. I have always used a fuel stabilizer and keep the tank full (filling it with a screened filter) with a added inline filter. In 20 years of my chipper-vacs life never have I had fuel problem.

Posted on Oct 12, 2009

radar001
  • 1051 Answers

SOURCE: brand new, troy-bilt chipper model 4265. put oil

Sounds defective. Even if you could fix this problem something else is bound to go wrong. Troy-Bilt has a reputation for quality products and I'd suggest, since it's brand new, you get it replaced.

Posted on Apr 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I trouble shoot an engine that won't start?


Hi, Frank and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Bank angle sensor tripped and ignition/light key switch not cycled to the "OFF" position and then back to the "ON" position.
5. Faulty starter button/switch.
6. Faulty jiffy stand or clutch pull in switch/sensor.
7. Security alarm needs a reset.
8. Starter control circuit, relay, or solenoid faulty.
9. Electric starter shaft pinion gear is not engaging or over-running starter clutch slipping. Good luck and have nice a day.
Steps to Take When Your Motorcycle Won Start Dennis Kirk Powersports Blog
What to do When Your Motorcycle Won Start
Troubleshooting No Start Honda Motorcycle
Motorcycle Won Turn On Solved

Mar 06, 2016 | Motorcycles

1 Answer

Electric start on craftsman 9 hp snow thrower won't start engine it sound like it's turning but engine won't start. I can start engine with the pull rope. Started last week with the electric start.


Sounds like you need to replace the gear drive on the starter. If the starter turns but the engine is not turning you have starter problems.

Jan 22, 2015 | Garden

1 Answer

Troy bilt pony 17.5 won't start and wires heating up


low battery or weak starter pull plugs spray pb blaster in cylinders make sure it isnt siezing up on you

Oct 11, 2012 | Briggs & Stratton Briggs Stratton Intek V...

1 Answer

911 electric start repair


remove the starter and see if the gear is broken

Aug 09, 2012 | Garden

1 Answer

I have a Yamaha DT125X 2006 model which i have had for about 3 years. Its always been a good runner and since iv had a car i obviously havent used it much, but i went to start it the other day and...


Hi, Ben_paice before testing any electrical component in the Starter Circuit it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test because your battery may have 12.5 volts or more but little or zero amps causing the battery to be faulty and must be replaced, especially "AGM" batteries.
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter.
4. Bank angle sensor needs a reset or is faulty.
5. FOB battery low or dead.
6. Faulty ignition switch.
7. Faulty starter button.
8. Faulty kickstand or clutch pull in switch/sensor.
9. Security alarm needs a reset.
10. Starter relay, solenoid, starter have failed or circuit wiring faulty.
11. Starter armature or field coils have failed.
12. Main fuse or circuit breaker may be blown or faulty.
13. The electric starter is working but starter clutch has failed.
14. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Thread DT 125 won start
What to Do Check When Dirt Bike Won Start
Yamaha DT125RE 2005 Service Manual
OEM parts for Yamaha
http://www.dt125.cz/download/Owners_Manual-DT125X_RE.pdf

May 11, 2017 | 2006 Yamaha DT 125 X

1 Answer

Have a new electric shredder does not have


Brand new shredder with no owners manuall I plugged it in.it won't start is there a first time procedure t o use it

Jul 10, 2010 | McCulloch Electric Chipper Shredder

1 Answer

Have a Karacher k-3.86 ELECTRIC pressure washer


Check the reset button on the GFCI plug to be sure it's in. Once you pull the trigger keep holding it for at least 10 seconds to let the water push the air out and then it should start running.

Apr 16, 2010 | Karcher K 2.25 R Electric Pressure Washer

1 Answer

Brand new, troy-bilt chipper model 4265. put oil in engine filled it with gas and tried to pull the recoil starter. It's locked up. I could lift this unit in the air with the recoil starter.


Sounds defective. Even if you could fix this problem something else is bound to go wrong. Troy-Bilt has a reputation for quality products and I'd suggest, since it's brand new, you get it replaced.

Apr 10, 2010 | Troy-Bilt Chipper Shredder

2 Answers

Need owners manual for 2001 yard machine chipper schredder model #24A464B131


I have a operator's manual for 24a 463b129 5.5 hp. I also have an operator's manual for the engine (Tecumseh). I purchased the chipper new from Home Depot back in 2002. I think you will be disappointed at the lack of information. If still interested, e-mail me your e-mail address, and I can send you a PDF copy of these manuals. (wchan@bushbros.com)

Mar 27, 2010 | Yard Machines 24a 452g729 5.5 Hp Chipper...

1 Answer

I have 9 hp Craftsman chipper vac with a manual pull start I want to upgrade to an electric start What is involved? Is there a kit to do this?


If it has the option of electric start all you need to do is puchase the starter from Sears and bolt it on. No to hard at all. But for a more definite answer you need model and serial #'s
Kurt

Mar 18, 2009 | Craftsman 6.5 Hp Chipper Vac

Not finding what you are looking for?
Troy-Bilt Chipper Shredder Logo

Related Topics:

157 people viewed this question

Ask a Question

Usually answered in minutes!

Top Troy-Bilt Heavy Machinery Experts

quennie732

Level 2 Expert

393 Answers

Mike

Level 3 Expert

4336 Answers

cwradio73

Level 3 Expert

1162 Answers

Are you a Troy-Bilt Heavy Machinery Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...