Question about Cardiozone Supersport Hr Club Commercial Treadmill

2 Answers

E1 error code

The board goes to a E1 code after 3 sec. The motor will never initially start up. If you remove the belt and simulate the motor running by moving the belt manually you can keep going because it does not error out. I can't get any information on the output voltage of the board so I can test it. They just want to sell the new $500 + dollar board.

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

My felax trademill starts counting to 3 , then nothing after then E1 will appear ,and
something it display E9, E4 , what to do just help me

Posted on May 28, 2012

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Cardiozone Master
  • 832 Answers

Lets eliminate the motor first, unplug unit remove motor shroud fin the 2 leads from motor to lower board. Connect a 18v DC battery to the leads this start the motor to move at approx. 1 mph if it does motor is good,if not you may worn motor brushes worst case open connection in the motor.
Now if the motor is good then reconnection the leads and plug in unit the lower board should have some LEDs lit up. Now find the LED that says PWM start unit if that light should start to flicker then the upper board and wire harness are work properly. Turn off the treadmill then turn it on and with a multi meter insert the leads into the connectors that go to the motor, then put the meter on 200v DC then start the treadmill you should get a reading 5 to 10v DC if you get 0v DC then the board will need replacing

Posted on Jul 19, 2010

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What can I do for F5-E1 situation


Check this article as the cause could be the control board, the door lock mechanism or the Membrane Keypad!


Whirlpool Oven Common Problems and Causes

Jan 08, 2015 | Ovens

1 Answer

Cardiotech x7 e1 code


test the input terminal motor, if there are the motor is faulty, see my personal TIPS 2) test the output voltage from control board, if there ARE NOT for input voltage motor, the board is faulty. see the diagram attached. 3) the error coming from speed sensor, Run the software calibration for easy diagnostic and fix it. However you must LUBE the deck belt,+rollers bearing front +back see the video attached.

God bless you
315fb2a6-9691-407c-81e1-b939a7c23c24.jpg

Nov 27, 2013 | Exercise & Fitness

1 Answer

Treo 121 treadmill. E1 error


Does sounds like a speed sensor. I would replace that first before doing anything else. You might have a blinking led on the controller that blinks when the belt is running...if you do and it blinks when you turn the belt manually, the sensor is good. If thats the case then you may have a bad wiring harness or controller.

May 16, 2013 | Exercise & Fitness

1 Answer

E1 ERROR on Trojan treadmill


Step 1:

This is probably a1) faulty speed sensor or the speed sensor adjust see the diagram attached..2) Clean it very weel 3) pluged very strong.
1_7_2013_4_47_16_pm.gif

Step 2:

also possibly a a)faulty motor tes the input voltage , if there are the motor need repair see my personal TIPS for motor help. b) lower board, measure the output voltage board for inpt voltage motor, if there are NOT the board is faulty, replace see the block diagram and wiring diagram.
. The error codes will differ between makes and models but could be e1.1_7_2013_4_49_28_pm.jpg1_7_2013_4_49_42_pm.gif

Step 3:

Finally see the video and LUBE the deck belt and rollers bearing too, proceed according.

Jan 07, 2013 | Exercise & Fitness

1 Answer

My treadmill will not start and I get an error code E1 after about a minute. What can be wrong?


1) you have speed sensor error, adjust see the diagram, clean it, and tight the wires connector very well.
2) LUBE the deck belt, very well
3) lube the rollers bearing too
4) measure the input voltage motor, if there are the motor need repair.
5) measure the output voltage board, for input voltage motor,if there are not the board is faulty. see the diagram.

7_17_2012_10_30_06_am.gif7_17_2012_10_30_29_am.gif7_17_2012_10_30_55_am.gif

Jul 16, 2012 | Exercise & Fitness

1 Answer

Technofit TS500i treadmill error code?? ( E1 & E2) please help!!!!!!!!!


Dear Sir:
The error code E1or E2 coming from this reasons.
1) Adjust the speed sensor, see the diagram attached, clean, and tight the connector wires.
2) Test the main motor input voltages coming from the output from the main motor board.
3) The main motor or motor board can be faulty or need repair.
See my personal TIPS for HELP and guide you.

sincerely. God bless you
4_24_2012_12_45_12_pm.gif

Apr 23, 2012 | Exercise & Fitness

1 Answer

Motor not going on York Optimum 60100 - after a while E 1 appears


Dear Sir:
This is probably a 1) faulty speed sensor or 2)the speed sensor is not plugged in properly. Its also possibly a 3) faulty motor control board or lower board 4) Main motor faulty. . The error codes will differ between makes and models but could be e1.You must test

see my personal TIPS for diagnose and troubleshooting.

See if you can run the software calibration for diagnose and trouble.

sincerely. God bless you.

ernesto cuadra
managua, nicaragua. c.a.

Mar 05, 2012 | York Exercise & Fitness

2 Answers

I have a v-fit PST-04 treadmill, model no DK 2510. When I switch it on and try and use it, it comes up with the Error Code E1 what does thos mean


Most E1 codes are speed sensor or no belt movement.
You wil lneed to unplug your unit the remove the motor shroud then plug unit in most Motor Control boards have LEDs. First thing I would do is start the unit look down at the board one of the light should start flickering this is a signal being sent to the lower board from your upper console. This tells me that the upper console and cable connecting the upper and lower boards is working also notice if the drive motor moved if not then E1 will come up. Now turn your unit off then turn back on to reset , next manually push with one of your feet the belt you should notice another flickering light the faster you push the light will flicker faster this tells me that the speed sensor is working if not replace the speed sensor. Next procedure check the motor using a fully 18v drill battery or car battery which ever is handy connect the two motor leads usually red and black in some cases black and white to the battery, if the motor move at a speed of approx. 1 mph then you have a good motor if not you can have worn motor brushes or open winding the motor.
If the upper board and drive motor are good then the only thing left is the motor control board if you have a multi meter handy connect the lead to the two spades that motor lead came off of the press start you should get a DC voltage of about 5 to 10V DC if not replace the board.

May 31, 2010 | Exercise & Fitness

Not finding what you are looking for?
Cardiozone Supersport Hr Club Commercial Treadmill Logo

1,082 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cardiozone Exercise & Fitness Experts

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Sportsmith LLC
Sportsmith LLC

Level 3 Expert

914 Answers

Tom Chichester

Level 3 Expert

33344 Answers

Are you a Cardiozone Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...