Question about Fisher and Paykel GWL11 Top Load Washer

1 Answer

Himy f&p GW509 will not drain (just a continuous beep) I have taken out the pump - nothing blocking it so bought a new pump still the same problemif i keep restarting it will eventually empty please help

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Fisher and P... Master
  • 713 Answers

Hi just found your posting.Sorry I have been off line for a couple of days.Do you still require help?If you do then please let me know if there are any lights that come on when the machine beeps.Looking forward to your reply.

Posted on Jul 10, 2010

  • mattyhumpho Aug 24, 2011

    Hi, I am having the same problem with the same machine, are you still able to help out?

    The lights error is as follows - 00101011

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Got a Samsung Diamond Drum WA80V3 after I put in on quick was and start it goes 22 minutes and when at 15 it goes toe rinse but then the machine just stop doing anything. Water still inside drum. Maks n...


The drain pump is either blocked or failed. Check the filter if it's clear then you are most likely up for a new drain pump. Here is a link to the part you need and a video on how to do it. Samsung DC31 00030E DRAIN PUMP B20 3 120V 60 NEW ORIGINAL

Mar 15, 2015 | Samsung Washing Machines

1 Answer

Why my AEG F55080vi stops after drain cycle (program beginning) and then it stops and I hear 2 beeps and 2 flash continuously?


Definitely, water drain time-out. Error code i20.
The pressure switch doesn't return to EMPTY (1-2) after two drain phases lasting 120 seconds.
Possible causes:
Drain circuit obstructed/blocked; drain pump
interrupted or jammed (foreign bodies); level
pressure switch blocked on FULL (1-3); hydraulic
circuit of pressure switch obstructed; wiring faulty;
circuit board faulty.

Thanks to your detailed description of failure I conclude that in drain phase (after starts drain pump) leaks water and causing a short circuit. I would thoroughly reviewed drain hydraulic circuit. If is alarm displayed and there is no water inside dishwasher then check heater and anti-interference suppressor.

Dado

Jul 12, 2014 | AEG Dishwashers

1 Answer

F&P MW511 HELP beeping and not draining


You have a blockage in the drain hose or pump,
Try to drain all the water out before you remove the pump

Error Code 37,
37. (00100101) Phase 1 to 6 - Pump Blocked Error ( No change in the water
level)
While draining, the water level reading from the pressure sensor has not changed
for over 3 minutes. There are three likely reasons for this fault. One is that the
drain hose or the pressure switch hose has been squashed or kinked and the pump
out rate has been dramatically reduced. The second possibility is that the pump is
partially or fully blocked. The third is that the pump is not operating due to Motor
Controller module, wiring or pump failure. This fault could also appear if the
machine is pumping to an unusually high head of drain hose or into an extended
length of drain hose. The Fourth possibility is a diverter valve fault or blockage,
water level is not altering as the diverter is stuck in the recirculation mode, giving
the module the appearance the pump is not lowering the water level.
Primary Source: Pump System.
Action:
1) Check that the drain hose has not been kinked.
2) Check the length of the drain hose and try to reduce the length if excessively
long. A 1 metre extension hose of the same diameter fitted to the existing
drain hose is the maximum allowable length.
3) Check for open circuit windings in the pump. (Note: Pumps are fitted with a
thermal cut-out which will reset on cooling.)
4) If the bowl is empty of water, remove the pump from the pump housing and
check that it is not blocked. Also check the drain hose is not blocked.
5) If the bowl contains water, then service the pump from the top of the machine
by removing the top deck and inner bowl. Bail out the water, remove the
pump cap and hood and clear the restriction.
Secondary Source: Wiring.
Action:
1) Check the pump harness is connected correctly to the pump.
2) Check continuity of the pump harness.
Tertiary Source: Motor Controller module.
Action:
Activate the pump by operating the machine in spin mode. Check the pump
is rotating. If it is not operating, and Primary and Secondary checks have
been performed, then replace the Motor Controller module.
Note: Consider fitting Pump Hood Kit (WM013). If 5kg Smartdrive fit splash guard to
pump.

Jun 10, 2013 | Fisher and Paykel GWL11 Top Load Washer

1 Answer

F & P Washer GW612 Wont drain fully unless you repeat spin a couple of times and then wont rotate have taken motor to be tested was (low?)Have replaced no improvement First and fourth light flash and...


Kate - firstly the windings of the stator when measured is 32 Ohms, earlier models was a lot lower between B-Y-R.

The washer will pump - rest pump (Cycles) during the spin cycle, if however it overheats then water will not be fully pumped out. A possibilty is the hose into the drain or sink is too high, or blocked somewhere.

In most cases the washer will indicate an error code.

The LEDS 1st & 4th from the right im assumming 10010000 = Fault code 144 - either you have a loose connection under the display/push buttons panel or you have a faulty motor control module

May 11, 2011 | Fisher and Paykel Fisher & Paykel Washer

2 Answers

Water is continuously draining from my samsung washing machine . due to this unable to keep washing the clothes .why the problem come & what is the remedial measure to rectify?


Possible that the drain value is half blocked and so is not able to block the water in the tub. Remove the connection to the valve and check if this drains , if so it is confirmed. Remove, clean the dirt and reset. If the leak stays then the valve is faulty.
Also it can be due to partial voltage to the drain valve to keep it open which means that the program controller is faulty. This is confirmed when the drain stops as the connection to valve is taken off.

Jan 13, 2011 | Washing Machines

2 Answers

Kreepy crawly keeps stopping but nothing is blocked


With Kreepy Krauly pool cleaners, it is usually something blocked so you have taken the perfect first step in finding your problem. You will also want ensure that the main drain and all suction lines are closed, except for the line to which the Kreepy Krauly is attached. Also, if this is a new purchase, it could be that your pump and filter system are too small to properly propel the cleaner.

Aug 13, 2010 | Universal Kreepy Krauly In-Ground Pool...

1 Answer

Sig amount of water remains at the bottom after a wash


First check that there isn't anything blocking the drain area inside the bottom of the dishwasher. Sometimes plastic wrap, a small Tupperware, etc. top gets sucked against the drain and blocks discharge. If nothing is there, (look really good, by getting out as much water as possible!!!). If nothing there, see if you have an "air-break" installed at the kitchen sink, this prevents backflow from the sink drain back into the dishwasher, check it by removing the decorative cover and see if it is clean and has no obstructions blocking water flow.

Another thing to check, is if you recently had a new disposal installed, it's possible that the dishwasher inlet was never "punched out" all the way to allow for the dishwasher to properly drain thru the disposal. If none of those, continue with the investigation!

Check to see if some broken glass might have worked its' way into the drain area, beneath the drain discharge guard. You'll have to remove the cover, some are just clipped in place while others have a screw holding them in place.

If still nothing, it is possible that something has worked its' way all the way into the discharge pump section and you'll need to remove the dishwasher from under the counter to get at the pump section.

Normally when the dishwasher is in the pump out sequence, you can hear the pump motor and impeller spinning. It is possible that you have a partial obstruction and will have to remove the pump housing to get at the problem

Bucket and towels will be needed to soak up all any water that you couldn't remove before pulling the dishwasher out from under the countertop.

If there is no obstruction in the discharge pump section check the discharge value (usually a simple rubber flap) is moving freely and has nothing obstructing it.

You should be able to cycle the dishwasher through a short cycle (wash & rinse) to see if everything is working OK again.

Jul 28, 2009 | GE GSD5620DBB Dishwasher

1 Answer

Fisher and paykel gw509 not draining, pump is clear


Check your exit hose spigot, it may be clogged. This is if your filter is all clean. There should be air for passage in the standpipe behind. Your hose should not fit airtight into the standpipe and neither too deep into it. Snaking out your standpipe would be good too.

Rate me pl.....if helped.

Mar 04, 2009 | Fisher Paykel EcoSmart GWL15

1 Answer

Drainage blocked on Whirlpool ADG 450 slimline inbuilt dishwasher, have taken out filter and cleaned it. Still blocked.


two things to check
if drain is plumbed nito a spigot on the sink trap, check that ther spigot and drain hose are not blocked - this is very common
also see if you can get to the drain pump and check there is nothing jamming the impellor. also if you have access to a multimeter, check if the drain pump is powered up

Sep 06, 2008 | Whirlpool Dishwashers

Not finding what you are looking for?
Fisher and Paykel GWL11 Top Load Washer Logo

Related Topics:

96 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fisher and Paykel Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Owen Barnes

Level 3 Expert

867 Answers

marley mcelhinney

Level 3 Expert

490 Answers

Are you a Fisher and Paykel Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...