Question about Roper RAS8244KQ Top Load Washer

1 Answer

My roper machine may have a leak somewhere. How do i get the back panel off, to take a look? I would also like to get a repair manual for my RAS8244LQO.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,554 Answers

This is a direct-drive washer and the part that usually leaks is pump which is directly coupled to the rear spline o the drive motor. The cabinet is removed for access to the machine parts instead of the back panel. You have to replace the pump if it is leaking.

Remove the screws securing the console to the rear of the machine then pull forward and up on the console and lay it back on the hinges.
My roper machine may have - ee3a8e8.jpg

Disconnect the lid switch harness connector by pressing on the tab, located in the middle, and pulling it up.
1bc7454.jpg

The cabinet is attached to the rear of the washer by two brass-colored retaining clips. Insert a flat blade screwdriver into the turned-up edge of the clip, located on both sides, and then pry back to release the clip from the slot in the cabinet.
1d88a5e.jpg

Open and hold the lid while grabbing the cabinet front opening then tilt the top of the cabinet toward you by pulling the cabinet away from the base. This releases the front and back slots of the cabinet from the tabs in the front and back of the base. Using the side of your leg and/or body as a support for the front of the cabinet, carefully lift up and set thMy roper machine may have - dcd3e8c.jpgside.
dcd3e8c.jpg

Pry the clips off securinMy roper machine may have - 2c78ac3.jpgto the motor and remove the pump.
2c78ac3.jpg
c613889.jpg

Posted on Jul 07, 2010

  • Jahn27
    Jahn27 Jul 07, 2010

    Replace the pump in reverse of the removal steps. Bring the cabinet to the front of the washer
    then slide the front bottom rail of the cabinet under the rail at the
    base
    of the machine then lay down the cabinet into position. Make sure the
    slots in the cabinet sit into the tabs at the base of machine.

    Secure
    the



    cabinet to the back of the machine with the two retaining clips.
    Inset the clips into the slots on the back of the machine then push it
    down into position to the slots on the cabinet.

    Reconnect the lid
    switch wiring harness connector and reinstall the console.




  • Jahn27
    Jahn27 Jul 07, 2010

    The pump is part number 3363394.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I clean between the glass and mesh on my roper microwave oven


That I would leave up to the professionals. If you are geting moisture or debris inside the glass then it is malfunctioning and needs professional repair. Call the service phone number locatedin the manual or in back of unit. These emit dangerouse uv rays that can harm you if leaking at the door. Never operate if you suspect it is not sealing properly.

Sep 02, 2014 | Roper Microwave Ovens

1 Answer

Roper washer is leaking above the motor.


Main gasket and seal on the bottom of the machine. You will need to replace the drum gasket and the bearing seal.

May 17, 2010 | Roper RAS8445KQ Top Load Washer

1 Answer

Roper washer leaks when filling


It's in the drain hose somewhere,during the fill the water gets as deep in the drain hose as it does in the washer,during the wash the pump runs in reverse keeping the water level in the hose low,during the drain the hose is filled again.
Prop the washer up in front on a couple bricks or boards,start putting in water until it starts to leak and take a peak under the machine.

Sep 27, 2009 | Washing Machines

1 Answer

Liquid detergent leaking from under control panel


am sending you this diagram to better knowlage of your michine.
this web includs parts, parts #
copy n paste
http://www.partselect.com/MultiModels.aspx?ModelNum=RAS6233KQ&searchTerm=&RefineSearch=0

"Did it solve your problem?"

May 08, 2009 | Roper RAS6233KQ Top Load Washer

1 Answer

Roper washing machine leaking water


Might be a cracked water valve or dispenser. To get to it you must remove the skin. Click HERE for info on accessing these fine machines.

Feb 22, 2009 | Roper RTW4100SQ Top Load Washer

1 Answer

Whirlpool "Roper" top-loading washer leaking


two screws hold back control panel on. panel flips up. two clips hold case on. remove clips and lid switch plug and whole outer case will tilt forward off machine base. pump is down in front and can be bought separate.

Apr 14, 2017 | Roper RAX4233PQ Top Load Washer

1 Answer

Washer machine leaks somewhere


take the control panel off, then the 2 clips that hold the unit to the back panel, then tilt off the cabinet to see the workings

Jan 28, 2009 | Whirlpool Estate TAWS750PQ 27-Inch Washer

1 Answer

Top loading Roper Washer id leakinf water


ok tom ...ready,,,look in the back of the console you will see at each corner a recess with a phillipshead screw,,,make them come up but dont remove them,,when the console comes lose from cabnit,,flip it back,,flip it back only and let it hang backwards..now theres a connect for the lid switch 2 gray wires connected to a brown and redess,,,ok now disconnect,,next in each corner is a brass clip 1 on each side take a screwdriver and pry them up softly...now pull the hold cabinet towards you,,but leave machine..keep me posted onthejob

Jan 27, 2009 | Roper Washing Machines

Not finding what you are looking for?
Roper RAS8244KQ Top Load Washer Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Roper Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Roper Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...