Question about RCA HDLP50W151 50" Rear Projection HDTV

1 Answer

NO PICTURE MY TV COMES ON I HAVE SOUND BUT NO PICTURE, THE POWER LIGHT BLINKS 5 TIMES THEN STOP BLINKING. IF I TURN OFF THE TV AND UNPLUG IT SOMETIMES FOR 30 MINS SOMETIMES FOR A DAY IT COMES ON WITH NO PROBLEM. PLAYS FINE FOR A COUPLE OF DAYS THEN DOES THE SAME AGAIN.AT ONE TIME I TOOK UOT THE BULB AND CLEAN THE LITTLE SCREENS OUT ON THE SIDE BECAUSE IT HAD A LOT OF DUST ON IT. COULD MY PROBLEM BE IN THE BULB OR THE LAMP POWER SUPPLY.

Posted by on

1 Answer

It is you senser that when you take the back end of your cover off there is a little chip there just tape it lol

Posted on May 11, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Sharp AquosTV model LC-52D64U. My kids were watching and turn it off and 1 hour later I try to watch tv but it won't turn on. A flashing green power light and ocp lights are on, the power


Do a hard reset to this set, and check. To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. This procedure will make it a hard reset. If it do not help you, make sure that the main board is faulty. Short circuited component/s at it. Contact any service technician; or the authorized service center. In most cases, the main board might have to be replaced. If so, a software [firmware] update too might be necessary.
These blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices. http://electronicshelponline.blogspot.com/
Blinking codes details to many popular brand TVs are given. Surf the site with patience. If blinks continue without any pause, the main board is faulty

Oct 18, 2014 | Televison & Video

1 Answer

TV power comes on but then I just get a blinking green light. No picture or sound.


Make sure your cable input is in properly. The TV might be going into a sleep mode if it not getting an input signal

Apr 03, 2012 | Philips Televison & Video

2 Answers

Turn tv on power light comes on but has no sound or picture then the standby light comes on and flashs and power light goes off


if the standby light blinks 6 times it has a bad backlite board (the most common with that set) other than that i will need to know how many times in a row it blinks. thanks....techman

Apr 01, 2010 | Sony BRAVIA KDL-52W3000 52 in. LCD...

2 Answers

Picture & sound go on & off every sec, red light blinks 5 times


helloFive blinks - AKB circuit (automatic kine bias), the timer/standby indicator blinks for about 30 seconds then goes to the self-diagnosis function. Something is wrong with the video. Check video out, Q705, 732, 761 and other components on the C board, also check Q218, 219, 220 on the A board. In addition, unit could be in IK blanking, try turning up screen slightly.

shaun

Oct 25, 2009 | Sony Grand WEGA KDF-55XS955 55" Rear...

4 Answers

Tv tunrns on then goes to stand by flashes 4 times & repeats


turn tv on picture comes up 2to3 seconds later tv blacks out then stand by red light flashes 4 times in a row repeatedly..can not turn on or off when stand by light starts flashing but before tv blacks out you can turn tv on and off repeatedly and picture and sound work.You have to unplug power cord for 30 seconds after stand by light comes on to get tv to turn on.

Mar 13, 2009 | Sony BRAVIA KDL-32S2000 32 in. LCD HDTV

3 Answers

Blinking Standby Light


KV32hs500 tv won't turn on. Standby light blinks 7 times, stops and then 7 more times, etc.. The tv will usually come on after about 2 hours or so of being off. Plays fine when on but once it gets turned off the problem happens again. Any suggestions? T.V. is 5 years old.
I have a similar problem . mine blinks 6 times or 7 sometimes also,and comes on with sound ,no picture for about 2 seconds then shuts off. Anything?

Jan 31, 2008 | Televison & Video

2 Answers

Sony LCD television will not power on.


I get 5 blinking red lights for about a minute or so before it powers back down. The Sony TV has a specific light that i presume is supposed to light up when the bulb is out. I'm unsure if this is what it is.
no picture, no sound. tries to boot with green light blinking a few times. then goes to red blinking light, six in all, then waits a few moments, then another 6 blinking red light.
Bulb was already replaced several months ago but we do have the TV on for long periods of time.

Jan 15, 2008 | Sony Grand WEGA KF50WE610 50" Rear...

2 Answers

No picture or sound - Power Save light blinks red 5 times - nothing on the screen


i also have the same problem with the flashing green light for a while then a different red light starts blinking on and off around 5 times....and i replaced my burnt bulb with a new one...still no picture.

Oct 24, 2007 | Sony Grand WEGA KF50WE610 50" Rear...

2 Answers

Troubleshoot-5 blinks red light front of TV


TURN TIMER OFF. GO TO SONY.COM, TROUBLESHOOTING, OR The STANDBY light is flashing on the television and there is no picture or sound. Solution
sp.gif sp.gif The STANDBY light will flash if an issue is detected within the television. This can sometimes be resolved by simply following the steps below to reset the television.
  1. Turn off the television. IMPORTANT: For a projection television that uses an internal lamp, wait 5 minutes after turning off the television to allow the lamp to cool before continuing with the following steps.
  2. Unplug the television power cord from the electrical outlet.
  3. Let the television remain without power for 60 seconds.
  4. Plug the power cord back into the electrical outlet. NOTE: If the television is plugged into a power strip or surge protector, remove it from the power strip or surge protector and plug it directly into the wall outlet. If the issue is resolved, the problem is with the power strip or surge protector and not the television.
  5. Turn on the television.
If the issue is still unresolved after following all of the troubleshooting steps, service may be required. Please note the number of times the STANDBY light flashes and relay that information to the service center.

May 17, 2007 | Sony KP-51HW40 51" Rear Projection...

Not finding what you are looking for?
RCA HDLP50W151 50" Rear Projection HDTV Logo

Related Topics:

106 people viewed this question

Ask a Question

Usually answered in minutes!

Top RCA Televison & Video Experts

The Knight
The Knight

Level 3 Expert

72256 Answers

matt martin
matt martin

Level 3 Expert

1207 Answers

Jaime Hernandez

Level 3 Expert

2296 Answers

Are you a RCA Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...