Question about Bosch Kitchen Ranges

Open Question

I am getting error code: electric 162 on my bosch dual fuel range what does that reffer to, I also have been getting an error message when i am cooking on Broil that says "please remove probe" but the probe is not inserted

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 159 Answers

SOURCE: Range problem

the control bord may be bad or the receptical where the probe connects may be bad and grounding out agenst the body of the oven. I would remove the plug and make sure the wires are good and its not grounding out. If it checks out ok replacement of the control bord should solve the problem

Posted on Jul 19, 2007

SOURCE: set probe temp or remove probe

my oven keeps telling me to input a temp probe and it keeps blinking and its getting on my nerves.

Posted on Sep 14, 2008

  • 1214 Answers

SOURCE: KitchenAid KESS907 Electric Range E1 F1 Error Code

F1 E1, replace Electronic Range Control.

In other words, the controller board has failed.

Posted on Jan 29, 2009

  • 1 Answer

SOURCE: F2 Error on Whirlpool Dual Fuel Range

I was baking and the stove suddenly changed to Maxi Broil and then to ERR F2EO Stuck Key. I cannot seem to change it by start or off or even turning the unit off and then back on. Any suggestions? Thanks.

Posted on May 29, 2009

  • 2 Answers

SOURCE: I have a KITCHENAID FREESTAND

We've had this same problem - they've replaced the electronic panel twice. They say it's a poor design as anything on the stove that splatters gets behind the front seal and kills it.

Posted on May 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to reset error codes


Dual Fuel Range Error Code 07 ' FAQ ' Sub-Zero and Wolf

www.subzero-wolf.com/.../dual-fuel-range-error-code-07

Sub?ZeroCore Issue: Dual Fuel Range error code 7; ERR 07 displays on Dual Fuel; Error 07 on control panel of Dual Fuel ... Convection Steam Oven Error Code E75.

L Series Built-In Oven Error Code COMM ERR ' FAQ ' Sub ...

www.subzero-wolf.com/.../l-series-built-in-oven-error-code-co...

Sub?ZeroCOMM ERR displayed on an L Series Built-In Oven indicates a communication error.Reset the unit's power at the circuit breaker. Turn the unit back on to see if ...

WWD30 Warming Drawer Error Code 40 - Sub-Zero and Wolf

www.subzero-wolf.com/.../wwd30-warming-drawer-error-cod...

Sub?ZeroError 40 on a Wolf Warming Drawer. Steps to Verify Issue: With error 40 on WWD30 warming drawer try the following before calling service: ... x. PF Error Code on Warming Drawer ... Whether you're shopping for appliances or have questions about those you already own, we've got the resources you need. ... Wolf Cooking.

Wolf DF304 beeping after turning off the oven - The Kitchen ...

appliantology.org > ... > The Kitchen Appliance Repair Forum

Dec 25, 2015 | Wolf Range Kitchen Ranges

1 Answer

I'm getting a periodic beeping signal and an "FO" error message from my lower oven. What is it telling me? The oven is a dual electric. Model number 326B1230P001. Thanks. Stanley Hochman


Hi!! Failure Code Fault Code Description Solution F0 Stuck touch pad Usually means that either the touch pad or the oven control (also called clock or ERC) is defective and needs to be replaced. If this fault code cannot be cancelled, replace the oven control (also called clock or ERC), touch pad, or both.
Although the manual recommends to replace the touch pad, try unplugging the unit form the wall for a couple of minutes to reset it. It works most of the time.
Good Luck!! Don't forget to rate this post!!

Sep 20, 2010 | GE Profile JGSP44 Dual Fuel (Electric and...

1 Answer

WHAT IS PF CODE ON A ELECTRIC STOVE


Hi,

Here is a tips that I wrote that will help to explain why you get the PF Error Code

PF Error Code for Appliances


heatman101



ll;l;[]

Aug 09, 2010 | Stoves 900DFa Dual Fuel (Electric and Gas)...

2 Answers

Kitchenaid DF Range F04 error code


I have a dual fuel kitchenaid convection range and I put it in self cleaning mode last night. Afterwards it said F 04 on the display. The doors open again, but neither of the ovens work

Nov 17, 2009 | KitchenAid KDRP487MSS Dual Fuel (Electric...

1 Answer

F2 Error on Whirlpool Dual Fuel Range


I was baking and the stove suddenly changed to Maxi Broil and then to ERR F2EO Stuck Key. I cannot seem to change it by start or off or even turning the unit off and then back on. Any suggestions? Thanks.

May 11, 2009 | Whirlpool RF315 Dual Fuel (Electric and...

1 Answer

VALLIANT VHR-C HEATER ERROR CODE F.06


I had a cool hot bath and suddently everything started working again!


Dec 17, 2008 | Bosch HDI7282 Dual Fuel (Electric and Gas)...

Not finding what you are looking for?
Kitchen Ranges Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bosch Kitchen Ranges Experts

William Miller
William Miller

Level 3 Expert

9047 Answers

Cindy Wells

Level 3 Expert

5062 Answers

yadayada
yadayada

Level 3 Expert

75197 Answers

Are you a Bosch Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...