Question about Wacom Cintiq 12WX Interactive Pen Display Monitor

Open Question

Cintiq 12WX only working as a second display?

I recently bough a Cintiq 12WX to use with my mac OSX with the latest updates and after following all the instructions the tablet only seems to work as a second display, I have tried to install it by disk and also using the most recent driver software off the Wacom website. When I check where the tablet should be in the settings theres just this message;
"A supported tablet was not found on the system"

Can anyone help or point me in the right direction? :( I really don't know what to try anymore. Thankyou in advance

Posted by on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
Fix-4U
  • 293 Answers

SOURCE: Problem with Cintiq 12wx

Hi...there Jenn!
Go to your toolbar bottom r/h side, look for VGA Display Icon. Open it and look for dual monitor setup. It's might be what you has been looking for... If not, read your cintiq user guide... Have a nice day!

Posted on Feb 03, 2009

Ad
  • 3 Answers

SOURCE: Hi, having problems with my

Hey guys,
I have posted the solution to this problem (or my version of a solution) elsewhere on this site - but here it is again, just for you!

I had a similar problem with my cintiq 12WX!
The way i did it was by going into CONTROL PANEL (please note i am using XP windows), then into DISPLAY, then into the last tab on the right aka SETTINGS. Once in SETTINGS go into the ADVANCED section, then click on the DISPLAY tab. In here you should have 3 things - monitor, panel and tv. The tv bit is irrelevant. Look at the MONITOR and PANEL tabs, if your wacom IS set up correctly when you click on the button (it is a circle with a line inside it) on the title (it will either be greeny/turquoise or red). If it is red, click it and the same button on the panel title will turn green aswell. Below the pictures of a computer and a laptop there should be 2 buttons that are the same for each. Currently, my almost working cintiq is set to having the button with two squares on it under the heading of 'MONITOR' and the button with a circle is on under the section entitled PANEL.
If this doesn't work I dont know what to suggest.
Hope this helps.
M

Posted on Mar 26, 2009

  • 2 Answers

SOURCE: My wacom cintiq 12wx suddenly began to stop

Try installing the latest driver for the Cintiq 12wx at the Wacom.com website for the Vista operating system :)

Posted on Mar 03, 2010

  • 1 Answer

SOURCE: The pen on my Wacom

Have you found a solution yet? I'm having the same problem. : (

Posted on Feb 21, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Cintiq 12wx is suddenly yellow-tinted


Did this problem get fixed? I am having the same issue :(

Sep 04, 2012 | Wacom Cintiq 12WX Interactive Pen Display...

1 Answer

Wacom cintiq 12wx calibration


I had a similar issue using the 12wx with a 15" MacbookPro Retina. Screen displayed the desktop way too much to the left. I found that the refresh rate of 59.8 hertz seemed to not be compatible despite it automatically being set. After changing this to 74.9 Hertz, the desktop is now properly centered on the Wacom screen and can be calibrated now. Not sure if this applies to Windows machines but perhaps something to keep in mind.

Jun 09, 2012 | Wacom Cintiq 12WX Interactive Pen Display...

1 Answer

I've had this same issue! My Wacom Cintiq 12WX tablet has been having this "Signal out of Range" issue all of the sudden with my Mac OSX Laptop. I've bought and tried new DVI cables and...


Hi 13ambreuer

"Signal out of Range"
is a problem between the graphics card, monitor, motherboard or graphics card port.
if you have to do troubleshooting on the monitor and display card, proved no problem to it. This means that the problem now is the motherboard and graphics card port.
(But should remember, problems ram, power supply and processor also causes the same error) * Sometimes *)
mean here you have to do the troubleshooting on all hardware on your computer

thnks&regards

Dec 08, 2010 | Wacom Cintiq 12WX Interactive Pen Display...

1 Answer

I just got a cintiq 12wx and when I plugged it in it worked immediately with my intuos 3 driver but had a message in the middle of the screen. uninstalled the driver and installed latest wacom cintiq...


I had this same problem and just had to go into my system preferences on the imac and select display and then select/check the mirror monitors and now it is on sync-hope that helps! After I did that though my color is off on the cintiq so I am looking for suggestions on how to fix it as the calibration did not fix the problem.

Nov 07, 2009 | Wacom Cintiq 15X Graphic Tablet

1 Answer

Cintiq 12WX screen not working :(


may be the power chord is damged go to a nearby shop and tell tham to give you a new power chord of monitor and then try it should work fine
thank for visiting fixya
have a nice day

Feb 19, 2009 | Wacom Cintiq 12WX Interactive Pen Display...

2 Answers

Problem with Cintiq 12wx


Hi...there Jenn!
Go to your toolbar bottom r/h side, look for VGA Display Icon. Open it and look for dual monitor setup. It's might be what you has been looking for... If not, read your cintiq user guide... Have a nice day!

Feb 03, 2009 | Wacom Cintiq 12WX Interactive Pen Display...

1 Answer

Hi, having problems with my cintiq 12wx. It is only working as a tablet right now. Using my pen on the cintiq, and it just moves the cursor on my other monitor. I can't transfer anything from my monitor to...


Hey guys,
I have posted the solution to this problem (or my version of a solution) elsewhere on this site - but here it is again, just for you!

I had a similar problem with my cintiq 12WX!
The way i did it was by going into CONTROL PANEL (please note i am using XP windows), then into DISPLAY, then into the last tab on the right aka SETTINGS. Once in SETTINGS go into the ADVANCED section, then click on the DISPLAY tab. In here you should have 3 things - monitor, panel and tv. The tv bit is irrelevant. Look at the MONITOR and PANEL tabs, if your wacom IS set up correctly when you click on the button (it is a circle with a line inside it) on the title (it will either be greeny/turquoise or red). If it is red, click it and the same button on the panel title will turn green aswell. Below the pictures of a computer and a laptop there should be 2 buttons that are the same for each. Currently, my almost working cintiq is set to having the button with two squares on it under the heading of 'MONITOR' and the button with a circle is on under the section entitled PANEL.
If this doesn't work I dont know what to suggest.
Hope this helps.
M

Feb 03, 2009 | Wacom Cintiq 12WX Interactive Pen Display...

1 Answer

Wacom Cintiq 20WSX + Mac Pro Early 2008 = kernel panics!


Try repairing permissions from the install disk, it works different/better

Jul 25, 2008 | Wacom Cintiq 20WSX 20.1 Interactive Pen...

Not finding what you are looking for?
Wacom Cintiq 12WX Interactive Pen Display Monitor Logo

Related Topics:

260 people viewed this question

Ask a Question

Usually answered in minutes!

Top Wacom Computers & Internet Experts

toddmat

Level 1 Expert

44 Answers

jasbo
jasbo

Level 3 Expert

2237 Answers

Ed Mac

Level 3 Expert

731 Answers

Are you a Wacom Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...