Question about Televison & Video

1 Answer

Where can I get the circuit diagram for the electronic ballast board (Matsushita HVP2603DD-1MA) in my Panasonic PT-L592E projector. It isn't shown in the service manual. Andrew

Posted by on

  • Andrew4812 Apr 18, 2008


    My e-mail is


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 563 Answers

Hi Andrew

Please give me your e-mail address and I'll mail you the original from Panasonic.



Posted on Apr 18, 2008

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to access ballast on pt-50lc13

The ballast is hard to completely remove--one plug all the way to the left as seen from rear and to the front, this does not really need to remove that.

The box is to the center and rear, unplug some plugs, screws and the box will come out far enough to replace the parts without removing the who thing from the set.

The large metal box with shields etc is the ballast.

Dec 22, 2012 | Panasonic PT-50LC13 50" Rear Projection...

1 Answer

Panasonic PT-52LCX16 - I need a ballast. Do they exist and where? lists the optical engine and ballast as available by special order: . However, Shopjimmy lists the power supply and lamp ballast with the part number of LSEP1206A1; it's out of stock there. Other sites just list this as the power supply so I'm not sure if the other sites include the ballast.

I wish that I could be of more help.

Cindy Wells

Oct 04, 2011 | Televison & Video

3 Answers

I need the service manual for the Panasonic PT-50LC14. Can u help. We have to change the Blue Filter and I cannot find my service manual. Thanks

It's $38.95 at Partstore at this link

Sep 28, 2010 | Panasonic PT-50LC14 50" Rear Projection...

2 Answers

New Bulb... No Screen...

Ballast Board ,it is what turns Lamp on! Call Encompass Parts for Part or look them up online they have website. Call 1-800-638-3328 Ok I looked it up Part# is LSEB3062A1 which showed No Longer avaliable,So try UED 1-800-648-6657 and Look on E-Bay under Electronics For Ballast Board.

Nov 19, 2009 | Panasonic PT-45LC12 45" Rear Projection...

1 Answer

The screen either does not come on at all, comes on after it warms us, comes on right away and then randomly fades to black, is black but audio can be heard. I just replaced the lamp but it still has the...

The ballast is the most common failure on these sets. The ballast is what supplies power to the lamp. If you physically see the lamp dimming/fading out when you loose the picture than the ballast is the issue. The ballast can be purchased from the following website. I would suggest a technician replace it as there are voltage charged up on it that are close to 400 volts. Please take a fe moments to rate my answer. Thank you...

Nov 18, 2009 | Panasonic PT-50LC14 50" Rear Projection...

1 Answer

How do I replace the ballister?

DLP TVs use Ballast board it is what turns Lamp on! Take back off look for capacitors 1000uf16v if any of these are puffed up on top they are bad.Ballast board plugs in easy to replace,for good working board look up on ebay got one for 57.00 Good Luck with the repair.

Sep 16, 2009 | Panasonic PT-50LC13 50" Rear Projection...

1 Answer

Need to rebuild ballest on Pamasonic PT-43lc14

You can get your ballast rebuilt at the following link or they may have replacement baaast available. Just hit the contact link and leave them a email.

Jan 24, 2009 | Panasonic PT-43LC14 43" Rear Projection...

1 Answer

Panasonic TV projector PT 4743G

yes the convergence ics will blow that resistor

Jan 21, 2009 | Panasonic PT-51HX42 51" Rear Projection...

3 Answers

Ballast problem on PT-40LC12

Sent me the serial number, and I can check for any re-call ...

my e-mail is <>

Feb 01, 2008 | Panasonic PT-40LC12 40" Rear Projection...

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

168 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

71126 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers


Level 3 Expert

66563 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides