Question about Canon PIXMA MP160 All-In-One InkJet Printer

2 Answers

Pixma 150 error msgs

(I am assuming in the following instructions "Power" button means "On/Off" button...correct?).

If so, when I "press the power button" while "pressing and holding the Stop/Reset button" the printer simply turns off. What part of this fix am I doing wrong?

1) With the printer powered off but connected to a power source, press the Power button while pressing and holding
the Stop/ Reset button.
2) When the Power LED is lit, press the Stop/Reset button two times while pressing and holding the Power button.

Posted by on

  • Steeple Jun 29, 2008

    I have an MP150 which is giving error code E27 - Ink Waste Absorber full - how do I fix this.



    Have tried this procedure but nothing happens.



    Any suggestions.



    Eleanor

  • Anonymous Mar 22, 2014

    I have ATT U verse with a 2Wire router. I press and hold the WPS button and then push okay, but even thought the printer detects the network it will not connect.

×

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Expert
  • 377 Answers

Hi dear

this the error code
E9 The connected digital camera / video camera does not support Camera
Direct Printing
E14 The Ink cartridges whose destination are wrong
E15 Ink cartridge is not installed E16 - Ink remaining is unknown
E16 -E19 Failed to scan head alignment sheet
E22 Carriage error
E23 Paper feed error
E24 Purge unit error
E25 ASF(cam) sensor error
E26 Internal temperature rise error
E27 Waste ink absorber full or platen waste ink absorber full
E28 Ink cartridge temperature rise error -
E29 EEPROM error
E33 Paper feed position error
E35 15 USB Host VBUD overcurrent error - USB
E37 17 Abnormal motor driver error
E40 20 Other hardware error
E42 22 Scanner error
E2-2 No paper (ASF)
E3-3 Paper jam
E4 No ink
E5-5 The ink cartridges are not installed or a non-supported ink cartridge is installed ,
or the ink cartridges are not installed properly
E8 Waste ink absorber full, or platen waste ink absorber full




First, download the software at http://www.box.net/shared/4yblbn34kg

Secondly, to run the software your printer has to be in service mode. Do that by
- unplug cable
- press and hold "power" button
- plug cable
- press "resume" and release
- release the "power" button
At this stage, your computer will detect a new hardware

Run the software.

oke

Posted on Apr 21, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 323 Answers

Did you turn off the switch, but leave the printer plugged in.?

Posted on Apr 20, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The yellow and green light flashes and printer error 5200 message displays


Error NO. 5200 is caused by ink absorber almost full so you need to reset your printer.. To solve the problem follow the instruction step by step ;
1. Turn off the printer without pulling the power cords.
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Then Press Resume button 5 times then let BOTH buttons go.
5. You will notice that the Alternate Blinking error is gone, this means that the printer is in Service Mode state. thanks

Aug 28, 2011 | Canon Pixma iP2700 InkJet Photo Printer

1 Answer

How can i fix a error like contack your service center


Please follow the instruction step by step....
1. Turn off the printer without pulling the power cords.
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Then Press Resume button 5 times then let BOTH buttons go.
5. You will notice that the Alternate Blinking error is gone, this means that the printer is in Service Mode state.

Aug 27, 2011 | Canon Pixma iP2700 InkJet Photo Printer

2 Answers

Error 5200 of canon pixma mx328. i already tried turning it on and off several times and even got the cartridges and returned them back but still when i tried to print a page error 5200 still...


Error no 5200 is caused by its temperature high.. to solve your problem follow the instruction given below::

1. Turn Off printer, cable power still plug in.

2. Press Stop/Reset button, don't release the button.

3. Press Power button by holding without release and than release Stop/Reset Button.

4. Press Stop/Reset button two times (2x) now release the Power Button.

5. Wait until service mode to zero (0).

6. Turn off the Printer, cable power still plug in.

7. Press Stop/Reset button, don't release it.

8. Press Power button don't release & than release Stop/Release button.

9. Press Stop/Reset button four times (4x), wait until service mode to "1"

10. Turn off printer, and loose cable power, wait for one (1) minute.

11. Connect cable power, turn on printer again, now this printer ready to use.

Aug 23, 2011 | Canon MX300 Office All-In-One Printer

1 Answer

Problem 5800


Hi! Your ink absorver tank is almost full, you need reset your printer. To reset your printer follow this instruction please : 1. Turn off the printer without pulling the power cords.
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Then Press Resume button 5 times then let BOTH buttons go.
5. You will notice that the Alternate Blinking error is gone, this means that the printer is in Service Mode state. Now your printer is ready to use.... thanks

Aug 12, 2011 | Canon Pixma iP2700 InkJet Photo Printer

1 Answer

Ink waste absorber


Canon error e27 ink absorber full/reset process

printer powered off but connected on power source , you must:
1. Press & hold stop/reset button, and then press & hold [ON/OFF] button.

2. When Green power lit, leave stop/reset button & press twice stop/reset (see orange indicator).
3. Leave On/Off button. Printer in actually service mode.
4. Press stop/reset 4 times (see orange indicator) if not blink restart above process from top.
5. After press stop/reset 4 times successful press On/Off button 3 times. printer will off.
6. Press On/Off button.

Jul 27, 2010 | Canon PIXMA MP150 All-In-One InkJet...

7 Answers

CANON PIXMA ERROR 5800


The waste absorber is full ,Replace the pads
then if you still get the error,you can reset it by following the directions below.
(reset without replacing pads can cause damage)

1) Enter SERVICE MODE By pressing Menu-Scan-Copy-Scan
2) Enter NVRAM by pressing <--- or ---> then OK
3)SET ABS-M LEVEL TO 0
4)OK

Jan 20, 2009 | Canon Pixma MP450 All-In-One InkJet...

1 Answer

Hello please help


Try re-setting the printer like this:

Canon MP150

1) With the printer powered off but connected to a power source, press the Power button while pressing and holding the Stop/ Reset button.
2) When the Power LED is lit, press the Stop/Reset button two times while pressing and holding the Power button.
3) When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a service mode. (Waiting for menu selection)
4) When the LED lights in green, press the Stop/Reset button 4 times.

Jun 06, 2008 | Canon PIXMA MP150 All-In-One InkJet...

2 Answers

Printer problem


E24 Purge unit error

Reset procedure:

Service mode operation procedures :
1) With the printer powered off but connected to a power source, press the Power button while pressing and holding
the Stop/ Reset button.
2) When the Power LED is lit, press the Stop/Reset button two times while pressing and holding the Power button.
3) When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a
service mode. (Waiting for menu selection)
4) When the LED lights in green, press the Stop/Reset button the specified number of time(s) according to the
function listed in the table below.(Each time the Stop/Reset button is pressed, the LED lights alternately in
orange and green, starting with orange.) The number of the Reset button pressing LED Function Remarks
0 time Green Power off
1 time Orange Service pattern print
2 times Green EEPROM print
3 times Orange EEPROM reset
4 times Green Waste ink counter reset See waste ink counter reset procedures below.
5 times Orange Destination setting See Destination setting procedures below.
6 times Green Print head deep cleaning
11 times Orange Button / LCD checking
12 or more times Returns to a menu selection
Reset except for the followings:
- USB serial number
- Destination setting
- Waste ink counter

May 11, 2008 | Canon PIXMA MP150 All-In-One InkJet...

1 Answer

Error code


Hi there,

Thanks for your posting in FixYa.

Please do the following and Let me know the result after that

  1. Turn off printer
  2. Hold down Resume button and press Power button.
  3. Keep holding down Power button and let Resume button go.
  4. Press Resume button 2 times then let BOTH buttons go.
  5. Green lights will flash and then stop blinking.
  6. When green lights are solid, press the Resume button 4 times.
  7. Press the Power button and the printer should turn off, if not, press the Power button once more.
  8. Your printer should respond as normal.
Don't forget to vote me.

Regards
Ellin

Jan 22, 2008 | Canon PIXMA iP8500 InkJet Photo Printer

Not finding what you are looking for?
Canon PIXMA  MP160 All-In-One InkJet Printer Logo

159 people viewed this question

Ask a Question

Usually answered in minutes!

Top Canon Office Equipment & Supplies Experts

kakima

Level 3 Expert

98868 Answers

old marine
old marine

Level 3 Expert

1573 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Canon Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...