Question about Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Whirlpool duet washer wont start at times.

It makes light clicking sound every few seconds when turned on, wont lock door. I've learned to tell immediately when its not going to work. I usually, after fooling with it leave it awhile,come back later and fool with it some more. Finally it will click one loud click and come on, and will work for several week or months after that.........when not working it flashes ....dL....which is not in the troubleshooting then some # I cant remember ( maybe 6).It is working now

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 8,619 Answers

Hi



Thanks for using FixYa. Error “dlf” or "fdl"or dl means a door latch failure. To resolve this issue the door latch assembly should be replaced however, before doing that you can leave the washer unplugged for 30minutes so that it resets itself. In the meantime when it’s unplugged just inspect the door latch wiring to ensure all the connector plugs are intact and not loose or broken. You can access the door latch wiring harness by removing the top panel of the washer. To remove the top panel just remove the three screws that hold the panel in place in the rear of the washer. With the screws removed, the panel will slide back, and then lift off. Locate the door latch assembly behind the front panel on the right hand side. Trace all the connectors from the door latch to the Central Control Unit (CCU) and make sure they are properly seated at both ends. If after doing this still the issue is not resolved then unfortunately you have to get the door latch replaced. Please do rate the solution if the issue is resolved or else revert for further assistance.



Thanks
Rylee

Posted on Jul 05, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My washer has an F dl problem?


Fdl is a code that indicates a door lock error. The clicking sound that you hear is most likely the door lock. This error occurs because the door cannot be locked. The door will try to lock six times before displaying the error code. You have a faulty door lock switch. Hope this helped and best wishes.

Jul 31, 2009 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

My Duet washer starts and runs for few seconds, then stops.


unplug machine take small panel off on bottom front of your washer, there should be a twist knob on pump, unscrew this (bearing in mind water will come out) you will find a strainer that catches debris before going through pump, clean out debris and re-intall. plug machine back in and try again.

Jun 22, 2009 | Whirlpool Duet GHW9150P Front Load Washer

2 Answers

F dL symbol on Whirlpool duet HT


It is saying there is a problem with your door Lock. when you close the door does it hold like it use too? try to open and close the door if it doesn't really close properly then you will just need a door latch. If the machine gives you an f11 code then its the main computer board that can also give your the door lock error. I would check the door first though.

Jan 09, 2009 | Whirlpool Gold Duet GHW9400P 3.8 Cu. Ft....

5 Answers

Control locked on ghw920 can u help me unlock


Press and hold the End of Cycle Signal button for three seconds. This will turn off the Control Lock feature.

Jul 12, 2008 | Whirlpool Duet GHW9150P Front Load Washer

2 Answers

Whirlpool Duet HT


its a door lock error a door lock error occurs if the door cannot be locked it will try to lock 6 times before displaying the error

Mar 28, 2008 | Whirlpool Duet GHW9150P Front Load Washer

11 Answers

Whirlpool duet


On the far right sode of the control panel there is a unlock control reset button. Hold it for 3 seconds and the fault will clear.

Mar 18, 2008 | Whirlpool Duet GHW9150P Front Load Washer

2 Answers

Whirlpol duet


sounds like your door lock switch may not engage.try opening and closeing the door. unplug the unit wait a few minutes plug back in and see if you can open the door. check to see if the door lock lights up.. hope this helps..

Aug 25, 2007 | Whirlpool Duet GHW9150P Front Load Washer

Not finding what you are looking for?
Whirlpool Duet GHW9150P Front Load Washer Logo

147 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Sal DeAngelo

Level 3 Expert

2122 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...