Question about Mitsubishi VS-60603 60" Rear Projection Television

2 Answers

Cannot receive inputs other than Ant A and B

Last night we lost power in the house. Today, we cannot find any inputs other than the ant inputs. Before the power out, I was able to see all of the inputs (i. e. input 1, 2, svideo, etc.

Please help.

Posted by on

  • 1 more comment 
  • imasia Jun 02, 2008

    same problem, lost power and now only Ant a and ant b.

  • nvieira75 Jun 22, 2008

    Hello,

    I recently had a power outage. My tv
    will now only allow me to switch inputs from Ant -A to Ant - B. None of
    the other inputs are accessible. Normally Ant-A is where i view my cable, but now i only get audio and the screen is black.

    OH,
    also the tv just shut itself of after 5-10 minutes of being on with
    audio but no visual. All of these problems from a storm??? UGHHHHH!!!!!!

    Thank you in advance for sharing your time and knowledge.



    Best Regards,
    Nigel



  • jjerez Aug 30, 2008

    A and B ANT only, also, white noise.
    Cable TV was out from video signals, now I use the RF cable, worked for some time and then went back to white noise but good picture.

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

If ANyone need a solution for this stby

Posted on Aug 31, 2008

  • jjerez Aug 31, 2008

    I tried the following (by advice of a locat tech) : use the original remote. Press Menu follow by Numbers 1,3,7,0. then select I belive first option... reinitiate or initiate then Enter.
    That fixed my problem.

  • Dean Stewart
    Dean Stewart May 23, 2011

    Here is the problem I just fixed with my VS-60603 Mfg date April 1999.
    Go to the menu.
    Go to "Locked to input 1"
    Switch it to No.
    Then you will be able to see all inputs and your TV is back to normal picture viewing!!!
    Cheers,
    Dean.

×

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 4 Answers

If you did not have a surg protector, you have witnessed the effects of a power surg that has most likely blown up your curcuitry....next time get a good Surg protector to prevent this from happaning again..

Posted on Jul 18, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Denon Stereo Receiver (DRA-345R) (quite an old model but has worked perfectly up until now) has a very static reception on AM. FM is fine. It started when I had my DirecTV upgraded with a Genie (whole...


it's obviously getting interferance fronm that whole house broadcast unit (not abnormal!) best and only thing you can do is to move the stereo to a place where you can get the MOST am stations the loop ant. is exactly what it says it is a loop of wire with two ends..both ends connect to the ant. input on the back of the unit..however if that whole house broadcast unit is the devil then an ant. no matter what or how it's made will only recieve more static not built to reject static! so you've got to move it unfortunately ..fm is a totally different band obviously fm isn't being affected by that whole home broadcast unit..you're lucky! on that count

Dec 12, 2013 | Denon AVR-2307 Receiver

1 Answer

To whom it may concern: July 12, 2010 (Order # 652165) I ordered an Ant Far & kit #174, requesting it be sent to my daughters house in a different city. On Aug. 3rd I received an email stating to...


Dear Mrs. Birch,
I understand your frustration with the Uncle Milton Industries and would follow the exact course you have set were it me in your place. Please understand that this site has no connection whatsoever with that company. We are here to help you solve a variety of technical problems and assorted issues in a wide range of catagories. Here is the email address for Uncle Milton's ant department:
mailto:ants@unclemilton.com?subject=Ant Replacements

I hope they resolve your issue quickly and to your satisfaction:)

Aug 24, 2010 | UncleMilton Uncle Milton's Ant Farm Game

1 Answer

Digital converter box worked with RCA analog TV and outside antenna. Had to unplug both for some work in house; when we plugged everything back in, there is no digital input. I checked everything over many...


Make sure you have an ANT. connected to the INPUT on digital converter box....then OUTPUT that signal to the INPUT of your TV....put TV on channel 3 or 4 or put TV on VIDEO if using red, white and yellow wires...power up and program converter box for channels....should work... if not try a set of rabbit ears instead of outside ant.

May 19, 2010 | Televison & Video

1 Answer

Orion TVD2710. Lost remote, can't change signal input


I would suggest you try to find a universal remote that has an "input" or "source" button and program that one to your tv. By pressing the "source" or "input" button, it will change the input to the tv. I hope this helps! -Der Strom

Apr 06, 2010 | Orion STV2763 27" TV

1 Answer

Lost entire picture, sound and everything else OK


check the invertor boards resistors they power the back lights
also check for any capactors that have blown (raised tops) they look little bateries

Dec 12, 2009 | Element Electronics FLX3220F 32 in. LCD TV

1 Answer

How do i use the ant. passthrough on tv2 in dual mode w/ dish dvr625


ANT. passthrough for an ant. connected to your 625 receiver will only work on tv 1. The only way to do this is to RF modulate your tv 2 coax to an RCA and hook the RcA cable to your tv2. then use another ant. to connect coax allowing you to pick up dish programing on an input and then going to the channels to enjoy local over the air programming.

Nov 26, 2009 | DISH Network DVR-625 DTV Receiver /...

2 Answers

My Ant A Input Not Working


Good Day, babt;
TRY THIS:

MAY ONLY BE ABLE TO SELECT ANTENNA A AND B. WITH THE REMOTE CONTROL PRESS MENU, SELECT "SET UP" AND THEN "AV CONNECTION HOME THEATER" SET "AV NETWORK" TO "OFF" AND "TV LOCKED TO INPUT 1" TO "NO" THEN EXIT THE CUSTOMER''S MENU, TURN THE UNIT OFF UNPLUG IT AND THEN PLUG IT BACK IN, IF THE PROBLEM RETURNS AN E2 RESET IS NEEDED. ACCESS THE OPTION MENU BY PRESSING "MENU 1, 3, 7, 0", USE THE ADJUST BUTTON TO SELECT "E2 RESET" AND PRESS "QV". IF THIS IS NOT RESOLVED BY THE E2 RESET REPLACE THE EEPROM, IC701 PART # 275P163010. THE E2 RESET IS ALSO NECESSARY AFTER REPLACEMENT OF IC701.
Good Luck, big IRISH.

Aug 06, 2008 | Mitsubishi VS-50603 50" Rear Projection...

1 Answer

I can't hook it back up


Is your DVD player a DVD/VCR combo? If so, hook the "tv out" (sometimes called "ant out" ) to the "ant in" on the DVD/VCR, then hook the "ant out" of the DVD/VCR to the "ant in" on the tv. Then make sure the DVD/VCR and TV are on the appropriate channel (3 or 4).
If it's NOT a combo, or these instructions don't work for you, i will need pictures of the inputs/outputs of the devices.

Nov 08, 2007 | DISH Network DVR-625 DTV Receiver /...

1 Answer

Setting up ant1 or ant2


Try pushing the source button on the remote until it goes to ANT 1 or ANT 2, then that part of the menu will not be grayed out. (Sidenote) If you take a pair of rabbit ears and attach them to the antenna input that says air, you can receive high definition local channels. Autoprogram the set at night, that is when most channels that send that signal, usually, show it at night. If it continues, reply to this post and I'll respond.

Aug 26, 2007 | Akai LCT3201TD 32 in. LCD Television

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

144 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1207 Answers

The Knight
The Knight

Level 3 Expert

71608 Answers

Jaime Hernandez

Level 3 Expert

2291 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...