Question about Xerox Phaser 8200 Laser Printer

1 Answer

Unexpected message: 6B22 - Xerox Phaser 8200 Laser Printer

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,072 Answers

That is a pre heater fault.

Preheater exit sensor in unexpected state during fault.
Preheater exit sensor in unexpected state during stage.

  1. Check system grounds.
  2. Check the Drum Maintenance Kit NVRAM contacts during oiling for continuity.
  3. Check the waste tray.
  4. Replace the Preheater ( REP 2.0.17).
B2M
B2N
B2P
B2Q
The preheat flag tripped unexpectedly while picking paper from Tray 2.
The preheat flag tripped unexpectedly while picking paper from Tray 3.
The preheat flag tripped unexpectedly while picking paper from Tray 4.
The preheat flag tripped unexpectedly while picking paper from Tray 1.
  1. Test the Preheater Sensor using Service Diagnostics.
  2. Check system grounds.
B3M
B3N
B3P
B3Q
B3S
B3T
The preheat flag timed out waiting for the paper picked from Tray 2.
The preheat flag timed out waiting for the paper picked from Tray 3.
The preheat flag timed out waiting for the paper picked from Tray 4.
The preheat flag timed out waiting for the paper picked from Tray 1.
Preheater sensor timed out during stage.

Posted on Apr 18, 2008

  • Rick Kasper Apr 18, 2008

    The paper heater transport is most likely defective.

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a message say: 41.3 unexpected size in tray 1


See several possible solutions for this exact message (41.3 unexpected size in tray) at:

https://www.fixyourownprinter.com/forums/laser/5864

Mar 06, 2014 | Canon PIXMA MX860 OFFICE AIO-2.5IN LCD...

1 Answer

Unexpected paper size message


go to the printer preference settings and change the paper size to A4 if you are using A4 and paper type to plain paper. and do the same on the printers settings menu.

Nov 12, 2013 | HP LaserJet 4050n Printer

1 Answer

Scanner not working


Re-install the Scanner software.

Tallon41

Sep 08, 2012 | Canon PIXMA MX860 All-In-One InkJet...

1 Answer

My hp scanjet 2400 stops at warming up then shows unexpected error. please help


Try connecting it on direct wall outlet.Not a surge protector or power strip

Try below solutions

An Unexpected Internal Error Has Occurred' Error Message Displays
Issue When attempting to scan, or, during the scanning process, the error message An unexpected internal error has occurred may display on the computer screen. There are three scenarios where this issue occurs. This document covers each scenario where this error may occur and provides links to the appropriate documentation for resolving each scenario. Solution one If you have multiple versions of HP Image Zone software installed on your computer, click here to download a patch that might resolve this issue . If you do not know if you have multiple versions of HP Image Zone installed, follow the instructions below.
  1. Click Start , point to Settings , and then click Control Panel .
  2. Click Add/Remove Programs .
  3. In the list of programs that displays, look for the following entries:
    • HP Image Zone
    • HP Photo and Imaging Gallery
  4. If there is more than one entry listed, then there are multiple versions of HP Image Zone software installed on the computer.
  5. Click here to download the patch. Follow the on-screen instructions to download and install the patch.
  6. If the issue persists, try the next solution.
Solution two Clicking Scan picture or image in the HP Director software results in an unexpected internal error or causes the computer system to stop responding. Click here to resolve this issue (c00369826). Solution three When accepting a scan from the HP Scanning preview window, the scanner may start to scan and then lock up with the lamp approximately ½ way down the scanner bed. This results in an unexpected internal error or causes the computer system to stop responding. Click here to resolve this issue (c00373192). Solution four When accepting a scan, the scanner completes the final scan and the lamp returns to the home position; however, when the image is being processed or sent to the receiving application (that is, HP Photo and Imaging Gallery), an unexpected internal error occurs. Click here to resolve this issue (c00373192). Solution five Immediately after clicking Scan Picture from the HP Director when using an HP Scanjet 3970 with v2.2 software, an unexpected internal error occurs.

Try also this link

http://h10025.www1.hp.com/ewfrf/wc/document?docname=c00259434&tmp_task=solveCategory&lc=en&dlc=en&cc=us&product=297430


I hope you issue should be fix to lessen your frustrations.You can do it

Regards

Your's Truly,

Christian from HP

Say "Thanks" by clicking the thumb icon in the post that helped you.

Please click "YES" in solution that solves your problem as "was this helpful?"
(Although I am employed by HP, I am speaking for myself and not for HP)

Apr 10, 2011 | Printers & Copiers

1 Answer

Won't print - Error message


You may have to re-install your printer drivers to solve this problem.
Sometime it happens.

Please don't forget to rate this answer if it helps.

Sep 08, 2009 | Printers & Copiers

1 Answer

I have an HP Photosmart Premium C3009 all-in-one printer. Sometimes it refuses to print with a message that says: The process stopped unexpectedly with status 1. I've looked in the manual and find no...


I also experienced the "process 'mdns' stopped unexpectedly with Status 1" message a few days ago with my new HP 7250, and found two solutions. Here are a couple of potential cures:

I downloaded the shareware program 'Printer Setup Repair', then ran their 'Reset and Backup' routine. Restarted, and bingo! Printing was successful. But trying to run either the HP scan software or the HP Ink Widget from Dashboard were not so successful. Got a 'Scanner not found' message. I then went to the printer, tried doing a manual scan there, sending the scan to my PowerBook. Once again, bingo. The scan was sent to my computer, and now the HP software could see the printer. I've since restarted both my computer and the printer several times; printing and scanning are working fine.

Now the second way to fix the problem. It's kind of hokey, but it seems to work, and is what led me to the The process 'mdns' stopped unexpectedly" with Status 1" problem in the first place. What you do is just add an ethernet router, that one you have lying around the house somewhere, between your DSL or cable modem and your Airport modem. Huh?

Here's the deal: when I first bought my HP multifunction printer, my wireless setup was this: Cable modem>Xsense ethernet router>Airport extreme. Unpacked and hooked up the HP printer, and it all worked immediately, perfectly. Print, scan, check supply levels, all no problem. Way too easy. Then, about a week ago I realized that the Xsense ethernet router that I had in the chain was really superfluous, as we no longer use ethernet in the house; might as well eliminate that unnecessary link in the chain. So I changed my setup to a simple: Cable modem>Airport extreme. At this point printing stopped. Tried everything I could think of, no go. Always got the "process ' mdns' stopped unexpectedly with Status 1" message. Put the ethernet router back in the chain, printing/scanning went perfectly. This made absolutely no sense to me, but it worked.

Left my setup with the extra router for a day or two until I remembered about the shareware program 'Printer Setup Repair', described above.

Before doing any of these steps it's probably a good idea to run Disk Permissions (I always run it before and after any installation), just to be sure you're authorized to be using the HP software.


Good luck!

May 04, 2009 | HP Printers & Copiers

1 Answer

During install message "trap monitor quit unexpectedly"


http://www.hp.com/#Support

Follow the link and get the correct driver and get installed

Also try with another USB cable, If you are using a long cable, just try with a short one.

Mar 19, 2009 | HP Photosmart C4280 Aio Printer

1 Answer

Image move toward 3/4 of page down ..... no idea what happens


hi,

unexpected page size is normlay caused by the client PC being set to either A4 or letter when it was expecting somthing else.

try and change your client to the correct paper size.
regards

Matt

Apr 14, 2008 | HP LaserJet 2840 All-In-One Printer

3 Answers

Unexpected Error (1001)


I have exactly the same problem, only my Deskjet is HP 3840 and I am running a PowerMac G4 with OS 10.4.10.

Dec 11, 2007 | HP DeskJet 5550 InkJet Printer

Not finding what you are looking for?
Xerox Phaser 8200 Laser Printer Logo

Related Topics:

295 people viewed this question

Ask a Question

Usually answered in minutes!

Top Xerox Printers & Copiers Experts

Whit
Whit

Level 1 Expert

185 Answers

iteminconline

Level 2 Expert

110 Answers

Philip Hughes

Level 2 Expert

63 Answers

Are you a Xerox Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...