Question about D-Link DI 514 Wireless Router (DI-514)

1 Answer

Hello I'd like to know how to cange routher ip address I have a DI-524 can you please show me?

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

It should be a box you fill in on the router configuration.
You access router configs by logging into the web page the router serves on your network. It may show up under Network (if Windows), else you simply type the current IP address into the address bar of your browser.

Dlink default is 192.168.0.1 with Username of admin and no password. You should be able to find it from there.

Posted on Jul 15, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have router DI-524 and am unable to connect to internet thru this router. But it says, it is connected


I would do a hard reset by pushing the small button on the back. You will need a small pen to push it. Push and hold down button till the lights flash I would/ say 10-15 seconds should be good enough. Once it's reset try setting up all of your settings again. Remember if you have dsl you will need you username and password to be inputed in some cases. If it is broadband most likely you will not have to bother with username and pass hope this helps.

Nov 30, 2009 | D-Link AirPlus DI-524 Wireless Router

1 Answer

DI-524 wired/wireless access point


Just for fun, make the router give out IP addresses starting at 192.168.0.101 forward. Configure the AP at 192.168.0.2 with no DHCP (the host will give out the addresses), a netmask of 255.255.255.0, and a gateway of 192.168.0.1. Now, let the laptop find DHCP, or give it a 192.168.0.x address where x is greater than 2 but less than 101.

How lucky is that?

Carl


Nov 19, 2009 | D-Link Dlink DI-514 Air Wireless 2.4 GHz...

1 Answer

Ip address


By default the IP address should be 192.168.0.1.

If it will not accept it
>Make sure your computer is wired or connected to your DI-524
XP version
>Try going start>run > type in CMD
>on the black screen type in ipconfig and hit enter.
>Look for the Default Gateway that would be the IP address that your DI-524 is using.

Windows Vista
>Click Start>All Programs > Accessories > click on command prompt
>type in ipconfig
>Look for IPV4 for the Default Gateway and that would be the IP address of your router.

If not allowing to access the login page, try pressing the reset button for 15 seconds at the back of your DI-524 but pressing the reset button will reset the setting of your wireles setting. Once your press the reset button type in 192.168.0.1 on the address bar and you should be having the login page. use Admin/admin for the username and leave the password blank and click ok...

Jan 31, 2009 | D-Link AirPlus DI-524 Wireless Router

1 Answer

DI-524 not working with Vista32 Dell M1330


make sure your wireless card is set to "obtain automatically an IP address"

Jan 25, 2009 | D-Link AirPlus DI-524 Wireless Router

1 Answer

Logging onto the DI-524 Router


hello..

The default username for the DI-524 is admin and the password is blank.

Jul 02, 2008 | D-Link AirPlus DI-524 Wireless Router

2 Answers

Wan indicator does not light up..


Hi there

Getting Started

Setting up a Wireless Infrastructure Network
8bd3361.jpg
Please remember that D-Link AirPlus G wireless devices are pre-configured to connect together, right out of the box, with their default settings.For a typical wireless setup at home (as shown above), please do the following:
1) You will need broadband Internet access (a Cable or DSL-subscriber line into
your home or office)
2) Consult with your Cable or DSL provider for proper installation of the modem
3) Connect the Cable or DSL modem to the DI-524 Wireless Broadband Router
(see the printed Quick Installation Guide included with your router.)
4) If you are connecting a desktop computer to your network, install the D-Link AirPlus G DWL-G510 wireless PCI adapter into an available PCI slot on your desktop computer. You may also install the DWL-G520, or the DWL-520. (See the printed Quick Installation Guide included with the network adapter.)
5) Install the D-Link DWL-G630 wireless Cardbus adapter into a laptop computer.
(See the printed Quick Installation Guide included with the DWL-G630.)
6) Install the D-Link DFE-530TX+ adapter into a desktop computer. The four Ethernet LAN ports of the DI-524 are Auto MDI/MDIX and will work with both Straight-Through and Cross-Over cable. (See the printed Quick Installation Guide included with the DFE-530TX+.)

Using the Configuration Menu

Whenever you want to configure your network or the
DI-524, you can access the Configuration Menu by
opening the web-browser and typing in the IP Address
of the DI-524. The DI-524 default IP Address is shown
bellow:
-Open the web browser
-Type in the IP Address of
the Router (http://192.168.0.1)
cf4c550.jpg
Note: if you have changed the default IP Address assigned
to the DI-524, make sure to enter the correct IP Address.

-Type admin in the User
Name field
-Leave the Password blank
-Click OK
22e0166.jpg

The Home>Wizard screen will appear. Please refer to the Quick Installation Guide for more information regarding the Setup Wizard.

Home > Wizard
1255162.jpg

These buttons appear on most of the configuration screens in this section. Please click on the appropriate button at the bottom of each screen after you have made a configuration change.
066a66b.jpg


Home > Wireless
08740e2.jpg

SSID- Service Set Identifier (SSID) is the name designated for a specific wireless local area network (WLAN). The SSID’s factory default setting is default. The SSID can be easily changed to connect to an existing wireless network or to establish a new wireless network.

Channel- 6 is the default channel. All devices on the network must share the same channel. (Note: The wireless adapters will automatically scan and match the wireless setting.)

WEP- Wired Equivalent Privacy (WEP) is a wireless security protocol for Wireless Local Area Networks (WLAN). WEP provides security by encrypting the data that is sent over the WLAN. Select Enabled or Disabled. Disabled is the default setting. (Note: If you enable encryption on the DI-524 make sure to also enable encryption on all the wireless clients or wireless connection will not be established.)

WEP Encryption- Select the level of encryption desired: 64-bit, or 128-bit

Key Type- Select HEX or ASCII

Keys 1-4- Input up to 4 WEP keys; select the one you wish to use.

Home > WAN > Dynamic IP Address
94836c8.jpg

Host Name- The Host Name is optional but may be required by some ISPs. The default host name is the device name of the Router and may be changed.

MAC Address- The default MAC Address is set to the WAN’s physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP.

Clone MAC Address- The default MAC address is set to the WAN’s physical interface MAC address on the Broadband Router. You can use the “Clone MAC Address” button to copy the MAC address of the Ethernet Card installed by your ISP and replace the WAN MAC address with the MAC address of the router. It is not recommended that you change the default MAC address unless required by your ISP.


Home > WAN > Static IP Address
eb48373.jpg
Static IP Address- IP Address-

Subnet Mask- ISP

Gateway Address- Primary

DNS Address- Secondary

DNS Address- Choose Static IP Address if all WAN IP information is provided to you by your ISP. You will need to enter in the IP address, subnet mask, gateway address, and DNS address(es) provided to you by your ISP. Each IP address entered in the fields must be in the appropriate IP form, which are four octets separated by a dot (x.x.x.x). The Router will not accept the IP address if it is not in this format.

IP Address- Input the public IP Address provided by your ISP.

Subnet Mask- Input your Subnet mask. (All devices in the network must have the same subnet mask.)

ISP Gateway Address- Input the public IP address of the ISP to which you are connecting.

Primary DNS Address- Input the primary DNS (Domain Name Server) IP address provided by your ISP.

Secondary DNS Address- This is optional.

Home > WAN > PPPoE
683d185.jpg
*** Please be sure to remove any existing PPPoE client software installed on your computers.

Choose PPPoE (Point to Point Protocol over Ethernet) if your ISP uses a PPPoE connection. Your ISP will provide you with a username and password. This option is typically used for DSL services. Select Dynamic PPPoE to obtain an IP address automatically for your PPPoE connection. Select Static PPPoE to use a static IP address for your PPPoeE connection.

PPPoE- Choose this option if your ISP uses PPPoE. (Most DSL users will select this option.)

Dynamic PPPoE- receive an IP Address automatically from your ISP.

Static PPPoE-you have an assigned (static) IP Address.

User Name- Your PPPoE username provided by your ISP.

Retype Password- Re-enter the PPPoE password

Service Name- Enter the Service Name provided by your ISP (optional).

IP Address- This option is only available for Static PPPoE. Enter the static IP Address for the PPPoE connection.

Primary DNS Address- Primary DNS IP address provided by our ISP

Secondary DNS Address- This option is only available for Static PPPoE. Enter the static IP Address for the PPPoE connection.

Maximum Idle Time- Enter a maximum idle time during which Internet connection is maintained during inactivity. To diable this feature, enable Autoreconnect.

MTU- Maximum Transmission Unit-1492 is the default setting-you may need to change the MTU for optimal performance with your specific ISP.

Auto-reconnect- If enabled, the DI-524 will automatically connect to your ISP after your system is restarted or if the PPPoE connection is dropped.

Home > LAN
4a9c31e.jpg
LAN is short for Local Area Network. This is considered your internal network. These are the IP settings of the LAN interface for the DI-524. These settings may be referred to as Private settings. You may change the LAN IP address if needed. The LAN IP address is private to your internal network and cannot be seen on the Internet.

IP Address- The IP address of the LAN interface. The default IP address is: 192.168.0.1.

Subnet Mask- The subnet mask of the LAN interface. The default subnet mask is 255.255.255.0.

Local Domain- This field is optional. Enter in the local domain name.

Home > DHCP
8d32e58.jpg

DHCP stands for Dynamic Host Control Protocol. The DI-524 has a built-in DHCP server.
The DHCP Server will automatically assign an IP address to the computers on the LAN/
private network. Be sure to set your computers to be DHCP clients by setting their TCP/
IP settings to “Obtain an IP Address Automatically.” When you turn your computers on,
they will automatically load the proper TCP/IP settings provided by the DI-524. The
DHCP Server will automatically allocate an unused IP address from the IP address pool
to the requesting computer. You must specify the starting and ending address of the IP
address pool.

DHCP Server- Select Enabled or Disabled. The default setting is Enabled.
Starting
IP Address- The starting IP address for the DHCP server’s IP assignment
Ending
IP Address- The ending IP address for the DHCP server’s IP assignment
Lease Time- The length of time for the IP lease. Enter the Lease time. The
default setting is one hour

Advanced > Virtual Server
58de0f2.jpg

If you would like to view more of this manual CLICK HERE

Thank you for using FixYa. Have a nice day and please remember to give this solution a good rating.

Jun 28, 2008 | D-Link AirPlus DI-524 Wireless Router

2 Answers

DI-524 Wireless


Yes you can, it's easy.

1. Just connect one of the LAN ports of the DI-524 to a LAN port of your other router. Leave the DI-524 WAN port empty.
2. Disable the DHCP server on your DI-524, your other router will be the DHCP server.
3. Assign a static IP address to you DI-524, different from your other router's. Example, if your other router has 192.168.2.1, you may assign 192.168.2.4. Make sure that the IP address you assign is outside the DHCP range configured in your other router and that the subnet mask is identical on both.

Feb 20, 2008 | D-Link AirPlus DI-524 Wireless Router

1 Answer

Disabled dhcp, cant access router with browser


the default ipaddress for that is 192.168.0.1 you will need to set your computer with a ip address like 192.168.0.2 then you should be able to access it. be sure to change your computer back to DHCP after you reset the router

Dec 26, 2007 | D-Link AirPlus DI-524 Wireless Router

2 Answers

Configure DMZ Host


enter username admin and password blank (nothing), i got 401 Unauthorized messege 3 times reset the routher DI-524

Feb 16, 2006 | D-Link DI-704P Router

Not finding what you are looking for?
D-Link DI 514 Wireless Router (DI-514) Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top D-Link Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2260 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18394 Answers

Are you a D-Link Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...