Question about Televison & Video

1 Answer

So far I have replaced the Lamp twice the light tunnel the color wheel all relatively successful operations except the color wheel.after replacing the color wheel the tv comes on with a picture that is skewed off to the right. I got into service mode from your instructions and centered the picture somewhat but I still have a dark stripe on the left edge of the screen. I cannot center the picture to get rid of that stripe. The instructions I followed were not for my model but for a 55 inch set which was on the screen even though I entered my model number in my question. Are the instructions the same for both models?

Posted by Anonymous on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 28 Answers

Optical engine is not installed properly in tv .

Posted on Jul 05, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Optoma gt700 is all green after replacing color wheel


we mainly retail or distribute color wheel, light tunnel ect sparet parts for projector or TV, so we have experience on that problem you faced.

perhaps you ordered a compatible color wheel,but it is not big trouble. compared with your old wheel, you will find a black tape, just make it as the same position as your old wheel, it will be ok.

Jun 25, 2014 | Optoma Office Equipment & Supplies

1 Answer

After replacing bulb, when the projector was turned on again, dark cloud area in bottom area of screen?


Please check the light tunnel and the reflector glass in the projector ,
it seems that the light tunnel or the reflector glass is failed

Have a nice day!
We supply original projector parts: lamp, bulb, Lcd panel, Lens, DMD chip, color wheel,
motherboard, powersupply ... with high quality and competitive price.
Jerry
Lampdeng Limited

Jan 16, 2011 | Sharp (AN-XR10LP) Projector Lamp for XR10X

1 Answer

Sony dlp 42" bad color wheel or bad lamp?


If Lamp has never been replaced its possible ,but sony is well known for Bad light tunnels or the Light engine. Call UED for information and Part 1-800-648-6657 and if Lamp call Mats 1-800-628-1118

Sep 20, 2009 | Sony Grand WEGA KDF-42WE655 42" Rear...

1 Answer

Samsug rear projection tv, everything looks green


Dust accumulation in color wheel, light tunnel, chip area can cause green tint.

It is very delicate area, light tunnel and chip can be easily damaged. Remove light engine assembly and color wheel. Blow dust out. Re-assemble. If the gasket around the color wheel housing is not replaced in the right position, or the housing screws not tightened correctly dust will contaminate the color wheel/light tunnel area.

Call someone that has done it a few times. If near Calgary, call me.


easyab

Jul 14, 2008 | Samsung HCM4216W 42" Rear Projection...

1 Answer

Samsung HLN617W wont come on


Unit does not have a flywheel. Assemblies include lamp, ballast, color wheel, dmd board, light tunnel, main and/or digital and analog pcb as well as power supply. These are all the assemblies in DLPs. The problem you described is usually lamp or ballast, but can also be from dmd or other circuit boards. Make sure lamp cover door safety switch is secure and fully engaged after replacing lamp or removing rear cover. I admit these sets are not cheap to repair. Good luck, Russmann.

Mar 27, 2008 | Samsung HLN617W 61" Rear Projection HDTV

2 Answers

Diagonal Shadow


Often a piece of foam, debris or such can get in between the lamp and color wheel which can cause the symptom your describeing.

Mar 17, 2008 | Samsung HLN617W 61" Rear Projection HDTV

1 Answer

Infocus X3 light tunnel


Are you speaking of the small prism shaped tunnel or the lamp itself? The prism or light tunnel may be accessed underneath the metal bracket that holds the color wheel in place. Be extremely careful as even breathing on this may cause it to collapse (ok, I exaggerate).

Feb 07, 2008 | InFocus X1 Multimedia Projector

5 Answers

Light tunnel


Greetings,

Thank you for your email inquiry. It appears you are looking for the light tunnel for a projector? My intial question to you is why are you seeking the light tunnel to your projector? also, which model is it?

Thanks,
cammykins

Dec 28, 2007 | InFocus ScreenPlay 4805 Multimedia...

3 Answers

Color wheel and lens


if u are not a technician, better have it check by a qualified one. because doing so might create more problems. service center have special tools and equipment for aligning and replacing these stuffs. just concern

Jan 14, 2007 | RCA HD61LPW42 61" Rear Projection HDTV

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

73698 Answers

Cindy Wells

Level 3 Expert

5062 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...