Question about Danby DDW2406 Stainless Steel Built-in Dishwasher

Open Question

My Danby Silhouette dishwasher failed to drain water and flashed error code 001 in the lcd window. What is the problem and how do I fix it?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: dishwasher will not run. clean light flashes seven times

I had success with the "Hi-Temp Wash - Normal - Hi-Temp Wash - Normal" sequence of button selections. This must occur within 6 seconds and initiates an internal diagnosis of the machine. The process runs for about 19 min. and shuts off. During the process several LED's light up and several funtions start and stop. If the machine has no broken systems, you should be able to open the door add some soap and the usual dirty dishes and carry on with normal operation. Thats all I have done and the wife is no longer on the war path. Good Luck

Posted on Mar 01, 2007

Falling Down
  • 67 Answers

SOURCE: Danby DDW1802W Cycle Problems

The fill valve is probably stuck in the full position. It's at the bottom of the tub and looks like a small tube with a cap on it. You should be able to move the cap up and down easily.

Posted on Nov 30, 2007

  • 1 Answer

SOURCE: Danby dishwasher E3 error

Same issue here so I just got off the phone with Danby. They said the E3 means the water is not hot enough when it goes into the machine. Now I dont know your guys situation but I let the water run hot until I cant touch it anymore, then I turn on the machine and plug it in. So it sounds like the heating mechanism is not working properly and does not heat the water to the appropriate temp to continue with the cycle. I will say that their support was really friendly and she informed me that since it was purchased less than a year ago it would be covered under the warranty. She gave me the number of a local repair shop. Lets just hope they dont tell me nothing is wrong with it because my water temp is fine. I will let ya guys know. Here is the number for Danby that I called. General office: 419-425-5052. Good Luck!

Posted on Feb 13, 2009

  • 1 Answer

SOURCE: Danby Dishwasher stuck in drain cycle after wrong soap use

There might be water in the overflow sensor. I unloaded the dishwasher and lifted the front so the dishwasher rested on its back. There's a narrow gray tube that runs down from the bottom right of the door. The tube runs into a white piece of plastic with some wires coming out of it. There is a rubber plug that covers a nipple on the plastic. Pull the rubber plug off. Mine was quite tight. Tip the dishwasher back onto its casters to drain the water from the overflow. Check to see if the dishwasher functions normally, then put the rubber plug back on.

Posted on Jan 10, 2010

mc1bean
  • 3053 Answers

SOURCE: My danby 22" countertop dishwasher wont **** water

Hello, cynthia

I was trying to help you out here. Maybe this will help some? I was going back to some customers that asked questions in the past and it appeared that no one answered them, so I thought I would take some of my personal time to see if I can help. Even though this site may not have your exact model or brand, This link will help you tons. Here is a link to about everything you want to know about your dishwasher, from repair to trouble shooting it,pictures, video's. Just scroll around and you will see tons of information to almost any question you might have on your dishwasher. If you go to this link and click around, I am sure you will find out so much about your dishwasher, you will know more that the company that made it. Here Is the link for you to click on>>

http://home.howstuffworks.com/dishwasher.htm


Please if this helped you at all, if you can find the time to rate my help and some kind words written would be appreciated for my free help , I would appreciate it. Here is also my direct link to my own pages of other areas of my expertise for other problems you might have in Automotive,Appliance, and Electronics. Drop In anytime for my help. Thanks,Mike

http://beta.fixya.com/users/mc1bean

Posted on Oct 27, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Haier dishwasher HDW9WHT beeps 5 times and won't wash what is wrong with it can I fix it or should I get someone in


7 results (0.54 seconds) Search Results

    Haier HDW100WH / HDW100SS - ProductReview.com.au

    www.productreview.com.au > ... > Dishwashers > Freestanding > Haier

    Rating: 1.7 - ‎30 votes
    Haier HDW100WH / HDW100SS: 30 customer reviews on Australia's largest ... 1.7 out of 5 stars for Haier HDW100WH / HDW100SS in Freestanding Dishwashers. ... I putthis review in to do my part for what I think is a great consumer service you ... it it keeps beeping 10 times telling me doors open??and won't begin cycle.

    Haier Dishwasher Error Fault Codes - Lights Flashing ...

    removeandreplace.com/.../haier-dishwasher-error-fault-codes-lights-flash...
    Dec 21, 2015 - Haier dishwasher error codes - flashing lights - beeping ...Dishwasher keep filling water and draining at the same time ... Fix Washing Machine That Won't Drain - Washer Not Draining Water .... 2015; Samsung Galaxy Note 5 Quick Users Guide September 25, 2015; My Freezer Is Cold But The Refrigerator ...

    Dishwasher Has Beeping Sounds Blinking Lights - How To ...

    removeandreplace.com/.../dishwasher-has-beeping-sounds-blinking-light...
    Dec 21, 2015 - At times your dishwasher may need to be reset. ... Haier DishwasherError Fault Codes - Lights Flashing Beeping Sounds My Haier ... Fix WashingMachine That Won't Drain - Washer Not Draining Water .... 2015; Samsung Galaxy Note5 Quick Users Guide September 25, 2015; My Freezer Is Cold But The ...

    How to Troubleshoot & Repair a Dishwasher ' HomeTips

    www.hometips.com/repair-fix/dishwasher.html

Jan 19, 2016 | Haier Dishwashers

1 Answer

How do you fix Error code U1


U1 is displayed on the LCD as a "no tap" symbol. (time out on fill is after 175 seconds)

Possible causes:
• Water turned off
• Insufficient water supply pressure
• Blocked water softener filter (if fitted)
• Spilt rinse aid causing over foam in tub
• Incorrect detergent being used
• Motor rotor
• The machine is siphoning
• Inlet valve has failed
• Controller

Jul 08, 2014 | Fisher and Paykel 23 in. DD603H SS...

2 Answers

Water not drains,Danby Portable Dishwasher


I had the same problem and found the drain blocked at the outlet as it goes into the sink.

Dec 27, 2013 | Danby DDW1899WP Portable Dishwasher

1 Answer

Error code #4 on ddw1899wp danby dishwasher


see this possibles causes:
you must read your instruction manual and go to the section troubleshooting for fix it the error codes. If you do not have go www.fitness.manualsonline.com or www. retrevo.com

God bless you

May 25, 2012 | Danby Dishwashers

1 Answer

Dishwasher: danby ddw1806bsl. Getting error code E4 "too much inlet water". How to fix that?


There is a tank with an overflow sensor on the right side of the dishwasher. The tank needs to be drained of water to reset the sensor. If necessary remove the insulation on the lower front corner of the machine and drain into a cup or container by removing the black rubber plug at the bottom of the plastic tank.
Consult the manual for detailed procedure.
The error can occur from excessive foaming.

Sep 22, 2010 | Danby DDW1806BSL Stainless Steel Built-in...

1 Answer

Danby diswasher ddw1806bsl e4 code


There is a tank with an overflow sensor on the right side of the dishwasher. The tank needs to be drained of water to reset the sensor. If necessary remove the insulation on the lower front corner of the machine and drain into a cup or container by removing the black rubber plug at the bottom of the plastic tank.
Consult the manual for detailed procedure.
The error can occur from excessive foaming.

Apr 07, 2010 | Danby DDW1806BSL Stainless Steel Built-in...

1 Answer

Danby error code 002


I spoke with Danby, and this error indicates the fact that the dishwasher is unable to fully drain. Likely causes are a kink in the hose, hose is too high on the drain pipe to drain, or, the pump motor is dying.

Seeing as mine's been mounted without fault in the same place for 2 years, I think I can tell you which one I have.

Dec 22, 2007 | Danby DDW2406 Stainless Steel Built-in...

2 Answers

Danby Silhouette leaking


check that the removable bucket did not alter a water guide near the cooling fins

Jun 05, 2007 | Danby DDR600R Silhouette Dehumidifier

4 Answers

Danby ddw2406


Simple solution. DO NOT spend the money on a tech coming to the house.
This error code comes from getting too much water in your machine, either from a dish filled with water emptying, or perhaps a clog from the sink that prevents your machine from draining. It is meant to prevent overflows from too much water being in the tub. It is a simple fix though!
First of all you should at least shut the power off on your machine. For the effort of a couple of more steps, it wouldn't hurt to shut the breaker off at the fuse panel. You will have to unscrew the undercounter tabs that mount the dishwasher to the countertop. They are located just under the counter sticking out from the top of the dishwasher when the door is open. Then proceed to pull out the dishwasher from under the counter. You will only have to pull it out about half way and you will find the overflow valve. It is located on the right side of the dishwasher just under the insulation and level with the lower hinge on the door. (Right side when you are looking at the machine.)
There are two overflow valves. One looks like a small cup, the other looks like a cylinder with a float in it like your toilet. Both of them have black rubber covers near the bottom. Take these covers off and about a quarter cup of water will flow out of these overflow basins. Allow them to completely empty, then replace the rubber drain covers and then replace the unit under the counter.
Once you turn the power on, the error code should be cleared and you are ready to use the dishwasher again.

Jun 03, 2007 | Danby DDW2406 Stainless Steel Built-in...

5 Answers

Error message 004


Simple fix for me
Simply look at right side of machine get a flash light pull the insulation away from machine stick the light in look for the white little resovoir and the styrofoam float switch.
syphon the 1/2 cup collection this allows the float in the attached
cup to drop kicking the sensor out....
I dont suggest disconnection the sensor as im sure it will come back to haunt you. =)

worked for me takes 5 minutes
enjoy

Nov 12, 2006 | Danby DDW1805W Designer Series...

Not finding what you are looking for?
Danby DDW2406 Stainless Steel Built-in Dishwasher Logo

Related Topics:

205 people viewed this question

Ask a Question

Usually answered in minutes!

Top Danby Dishwashers Experts

Brad Brown

Level 3 Expert

15441 Answers

Kevin Getz
Kevin Getz

Level 3 Expert

1031 Answers

Andrew Taylor
Andrew Taylor

Level 3 Expert

14548 Answers

Are you a Danby Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...