Question about Scotts Lawn 73740 SPDY GREEN 3000 B/C S 3 EA 13610498

1 Answer

Calibration What do the numbers mean

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 63 Answers

They are the settings u used depending on what feed u are using
aon the back of any feed they indicat the number u need

Posted on Jul 25, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My 2007 checy impala read "calibration complete" what does that mean ????

Refer to Electronic Compass Calibration do you have an owners manual ?
Compass Calibration
The compass direction will show CAL if it needs to be calibrated. Before calibrating the compass, drive the vehicle to an area that is magnetically clean (free of large metallic objects).
  1. Turn ON the ignition.
  2. Before calibrating the compass, make sure the compass is set to the variance zone in which the vehicle is travelling. See Compass Magnetic Variation Adjustment below.
  3. Press the vehicle information button until the PRESS TO CALIBRATE COMPASS screen is displayed.
  4. Press the set/reset button to start the compass calibration.
  5. The DIC will display CALIBRATING: DRIVE IN CIRCLES. Drive the vehicle in circles at less than 8 km/h (5 mph) to complete the calibration. The DIC will display CALIBRATION COMPLETE when the calibration is complete.

Oct 02, 2016 | 2007 Chevrolet Impala

1 Answer

Hello, my name is Lydie Dobri , my 2008 Lincoln MKX keep saying on the dash board calibration complete. what does it mean?

It can mean the Compass has been calibrated. It can mean the GPS has been calibrated. Someone could have switched from Kilometers to Miles and results were converted.

Jan 27, 2015 | Lincoln MKX Cars & Trucks

1 Answer

Can you calibrate a boss bv9055 touchscreen

Hello there ,

It depends on what you mean by 'calibrate' meaning . The ability to precisely adjust to known values.

Audio output,, size, video, speaker calibration ?

If it isn't in the manual, it doesn't do it friend.

The free manual is via here. just enter the 5 digit number captcha when asked.

Sep 20, 2014 | GPS

1 Answer

To stop auto calibration in toshiba color mfd

Better not to turn off the calibration, otherwise it will cause other errors.

If your colour printing is less than 5% ration, perform following. Turn the code 08-2692 "Prevention of color toner low density / ON/OFF setting" to ON, and then set number of sheets to be judged at the code 08-2693 "Prevention of color toner low density / Judged
number of sheets setting".
08-2693 u can put higher value such as 20 or above to delay the colour calibration.

Mar 25, 2014 | Toshiba E-studio 2330c 2830c Color...

1 Answer

Replace MAF sensor 1995 ford ranger 6 cyl 3.0L-can't find calibration number required for parts

in the driver door jamb near the striker there should be a sticker with calibration code it should look like this.

Jan 25, 2014 | 2004 Ford Ranger

1 Answer

Calibrating incline voltage

It sounds like you may have a shorted potentiometer. I would recommend replacing the VR (Potentiometer) Assembly. I have located it on the manufacturers website for $32.50, part number is 1200-28. If the nylon gear is broken, that part number is 6005-37. If you need the diagram, here is the link:
and the link for the parts list/order page:

Nov 29, 2013 | Nordic Track NordicTrack Treadmill, A2550

1 Answer

Check engine light is on with a P1491 code . what does that mean? 2004 1500 Ram quad cab,2 wheel drive ,4.7 engine

P1491 Secondary solenoid switch circuit malfunction you should not have this code you need to refeer to the dealer about the PCM calibration there is a recall on your vehicle The recall number is D24 incorrect PCM calibration

Jul 11, 2011 | 2004 Dodge Ram 1500

1 Answer

What does click calibration mean i keep get it when i switch my phone on

hi by the sounds of it you have a touch screen phone if so calibration means to calibrate your touch screen. hope this helps

Dec 18, 2010 | Cell Phones

1 Answer

After charging my sony reader 600, I have a message: Calibration error detected please restart calibration process. WHAT DOES THAT MEAN?

the touch calibration was affected due to charging in ON condition.switch off your mobile and charge it or try changing a original charger

Mar 20, 2010 | Sony Reader Touch PRS-600

2 Answers

Calibration is not right on my garmin 330

If you think the touch screen is not responding properly, press and hold the Power button until the
Calibration screen appears. Follow the on-screen instructions.

Aug 15, 2009 | Garmin StreetPilot C330 GPS Receiver

Not finding what you are looking for?
Scotts Lawn 73740 SPDY GREEN 3000 B/C S 3 EA 13610498 Logo

144 people viewed this question

Ask a Question

Usually answered in minutes!

Top Scotts Lawn Garden Experts

Dennis Key
Dennis Key

Level 3 Expert

2478 Answers


Level 3 Expert

708 Answers

john h

Level 3 Expert

15220 Answers

Are you a Scotts Lawn Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides