Question about Speck Pumps COMPLETE E90II PUMP Part number E90II OPT 51401 SPECK PUMPS Replacement Part

Open Question

Need parts for swimming pool parts Model number pe-71-11-h,serial

Need seals and impeller

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will the impeller on the intex model sf15110 fit the intex model cs8111


Don't think so, take them apart and you will find out. Be sure to have a replacement shaft seal.

Jun 08, 2014 | AO Smith 1.5 hp 3450rpm 56J Frame 115/230...

1 Answer

Swimming pool pump


check on amazon enter motor or pump number should give you numbers to order from

Jan 19, 2014 | AO Smith Pool Pump Motor Hayward Swimming...

1 Answer

How do I fix the seal?


please follow this steps . God bless you
  1. Turn off the pump motor and close the input and output valves.
  2. Loosen the fasteners that secure the tube connecting the pump and motor.
  3. Move the motor away from the pump housing.
  4. Remove fasteners holding the diffuser to the backplate.
  5. Inspect the diffuser and O-ring for wear, replacing as needed.
  6. As needed, remove fasteners attaching the impeller to the shaft. Alternately, the impeller may be screwed on to the end of the shaft.
  7. Remove the impeller and seal from the shaft.
  8. Inspect and replace the impeller and seal.
  9. Reassemble the pump.
5ad0fb72-ac24-4a0e-94fb-9faca07eee0b.jpg

Nov 23, 2013 | Hayward Sp2607x10 Super 1 Hp Swimming Pool...

1 Answer

How do I take it apart


follow this steps and fix it. God bless you
  1. Turn off the pump motor and close the input and output valves.
  2. Loosen the fasteners that secure the tube connecting the pump and motor.
  3. Move the motor away from the pump housing.
  4. Remove fasteners holding the diffuser to the backplate.
  5. Inspect the diffuser and O-ring for wear, replacing as needed.
  6. As needed, remove fasteners attaching the impeller to the shaft. Alternately, the impeller may be screwed on to the end of the shaft.
  7. Remove the impeller and seal from the shaft.
  8. Inspect and replace the impeller and seal.
  9. Reassemble the pump.
7e13e6cb-4b3a-4633-869c-5fb51a7ab1b0.jpg

Nov 23, 2013 | Hayward Sp2607x10 Super 1 Hp Swimming Pool...

1 Answer

Seal plate stuck on square flange


It sounds like the seal has a death grip on the motor shaft. Pick up the seal plate so the motor is hanging beneath it. (watch your toes) Holding it about waist high let it drop and then snatch it back up again. Kinda like getting a pillow in its case. The motor should drop out.

May 04, 2013 | AO Smith Pool Pump Motor 1HP Square Flange...

1 Answer

Have a Sta-Rite 1.5 hp Model #HMSF 1F - trying to get it apart to change seal- has been leaking and losing prime- four bolts hold the motor on- tried to separate there first but will not pull apart (maybe...


Remove impeller housing cover. Insert screwdriver carefully into back of motor to keep the armature from turning then unscrew impeller clockwise or opposite the direction of operation. Replace seal on impeller and pump housing. Lube seal with graphite. Replace impeller and housing cover. Remove screwdriver from motor. You should be good to go.

Sep 10, 2011 | Sta Rite 1 Hp Sta - Rite Abg Swimming Pool...

2 Answers

Put in new motor, but pump will not turn. a.j. smith motor, pentair ultra flow... installed new seals also


The most common reason is you left part of the old seal stuck on the impeller and the new seal is riding on top of the seal ring (black rubber) of the old and therefore is tom compacted and it binds up the pump. Double check you removed all the old seal parts.

If that's not it, with the impeller off, can you turn the motor shaft then?

John

May 29, 2011 | Pentair 15 Hp Superflo Swimming Pool Pump

2 Answers

I cannot start pumping. the pump runs but no water is circulating


I think you have spun the center out of your impeller. Disassemble your pump and replace the impeller if necessary. Also replace all seals while you are at it.

May 04, 2011 | Sta Rite 1 HP Sta-Rite Pump: 1.5" in/out,...

1 Answer

Looking to replace my elec. motor on my hayward pump # sp3605x7. ser# 640c30. not sure how you..remove the motor from the pump.did not see a set screw? thank you steve 978-606-9706.


Turn off the electric first. Then just remove the 4-6 bolts and separate the back half from the front. The motor with seal plate, impeller, and diffuser can all be pulled back away from the rest of the pump. Now disconnect the electrical from the motor and your can pull the motor with the seal plate, diffuser, and impeller all the way out and work on it. You need to remove the diffuser (plastic housing that goes around the impeller) sometimes this is held by a series of 3 to 6 small screws, other times it just slips over the impeller. To remove the impeller you need to lock the motor and unscrew impeller. Depending on the motor, you remove a cap in the middle of the tail piece and hold with a wrench, or remove a cap that covers the whole end and grab the shaft with a wrench (usually 7/16") by sliding it under one of the components (not sure exact part off top of my head have to look at it) and then turning impeller. If the impeller has a bolt or screw in the middle remove that first. It should be reverse thread so make sure you don't turn the wrong way and break or strip. If there is no screw, or after you've removed it, just spin the impeller off (it should be counter clockwise standard thread). If you can't do it by hand and assuming you don't have an impeller wrench, be very careful and use a large pliers, pipe wrench, or strap wrench to loosen it. After that you unbolt the motor from the seal plate, pull the seal plate away from motor (this removes half the seal), and then pop the other half of the seal from the seal plate. Make sure replace the shaft seal, and use a tiny bit of pool lube on the rubber parts when installing, but keep the white and black ceramic surfaces 100% free of any dirt, grease, etc while working with them. The instructions above a based on a very similar model and may vary slightly, let me know if something doesn't look/sound right and I'll clarify. Good Luck

Sep 24, 2010 | Hayward Single Speed 34 Hp Swimming Pool...

1 Answer

Tring to take the pump face off the motor


You have to remove the back cover from the motor. Next loosen the capacitor. Put a 7/16" wrench on the shaft and the pump impeller will screw off by hand.

May 28, 2009 | Sta Rite 1 Hp Sta - Rite Abg Swimming Pool...

Not finding what you are looking for?
Speck Pumps COMPLETE E90II PUMP Part number E90II OPT 51401 SPECK PUMPS Replacement Part Logo

Related Topics:

277 people viewed this question

Ask a Question

Usually answered in minutes!

Top Speck Pumps Pool & Spa Experts

k24674

Level 3 Expert

7993 Answers

Gil Shultz

Level 3 Expert

3368 Answers

Jay Finke
Jay Finke

Level 3 Expert

1338 Answers

Are you a Speck Pumps Pool and Spa Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...