Question about Samsung Washing Machines

1 Answer

My brand new Samsung J845 washing machine keeps showing an error message (which is not in the manual of 1E. What could this possibly be and how do I fix it?

Posted by on

  • Anonymous Mar 17, 2014

    wash until it gets to rinse and then stops giving 1E error message

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I contacted Samsung Australia and was informed that this was a Water Sensor Level fault. The machine will be fixed under their warranty guidelines. Thank you.

Posted on Apr 18, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have Samsung J845 front loader washing machine. The error code bE or 6E is showing up. It won't spin at all and barely drains


Possibly a short circuit to motor or PCB
Requires a competent repair engineer to fix.
Check mains supply
Check main control module
Check main drive motor

Mar 22, 2016 | Samsung Washing Machines

1 Answer

We have a Samsung J845 Front Loader. The door lock shorted out so we replaced it with a new one but now are just getting a DE error.


DE is door lock error possible main pba or wire harness check connections on new switch first .ohm wire harness If you can to check for break in wire

Mar 12, 2016 | Samsung Washing Machines

1 Answer

My Samsung fully automatic washing machine Model # WA13G2Q showing 1E error code.What do I do?


My Samsung fully automatic washing machine Model # WA13G2Q showing UE error code.What do I do? THIS IS MY EMAIL engrabih12@hotmail.com

Apr 13, 2011 | Samsung SW62ASP Top Load Washer

1 Answer

D3 error prevents washing machine from working Samsung F/L j845. possible cause door censor?, fuse? can you advise me


Took of the lid Looked at the door connection it had come off I reconnected it and WALLA it works.

Dec 07, 2009 | Samsung Washing Machines

1 Answer

Please help! My samsung 7kg J845 front loader keeps flashing UE on the error code (spin cycle) and I can't open the door. Sarah


Hi, I have the same washing machine and it flashes UE on the error code during spin cycle when I have one thing in there, or if the clothes are uneven. I usually have to wait until the lock light goes out, re-arrange the clothes and continue spin cycle. If it is just one item in there, I usually have to manually wring it out as it will keep saying error if I keep trying to spin.

Oct 22, 2009 | Samsung WF337AA Front Load Washer

1 Answer

Samsung J845 front loader washing machine. Error


Hi
An OE error presents if the washing machine has not successfully drained the water in ten minutes.
there are a few simple steps to take before calling for service.
Step 1: Check the drain pump filter.
Items caught in the drain filter will prevent proper drainage. Over time build up can occur from detergents and additives used in the machine. Manually drain unit through the drain hose, then lay a towel down to catch the water, and remove the filter. Clean the filter thoroughly and restart the machine.

Step 2: Check the washers drain hose.
If the drain hose is not installed properly, the washer will not drain properly. The drain hose should not be installed more than 1 meter higher than the bottom of the washing machine.

Step 3: Confirm that the washer is leveled properly.
If the unit is not leveled properly, it will not drain properly. The front of the unit cannot be higher than the back or vice versa. If not properly leveled, the water can flow back into the machine. If this is the cause of the problem, please level the machine using the supplied leveling wrench. When you place a level on the washing machine, the bubble should be in the center. Confrim that the washer is leveled from side to side and front to back.
you can perform a diagonal test when leveling the washing machine to ensure that the unit does not tilt from corner to corner.

Thanks for contacting fixya.com

Sep 30, 2009 | Samsung Washing Machines

1 Answer

My washing machine wont spin or move. It goes thru the whole cycle with no error message. Samsung J845


All fixed - it was the belt that needed replacing
YAY no need to buy a new one

Aug 20, 2009 | Samsung Washing Machines

2 Answers

Error message 1E is displayed at start up samsung model SW75C3S


1E error mean there is malfuntion on your sensor pressure. Maybe because the sensor is damage or rusted. You must replaced, it's cost me about $15

May 19, 2009 | Samsung SW62ASP Top Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

556 people viewed this question

Ask a Question

Usually answered in minutes!

Top Samsung Washing Machines Experts

Todd Marr
Todd Marr

Level 2 Expert

77 Answers

D. E. Hev

Level 3 Expert

1059 Answers

Chris Haynie

Level 1 Expert

3 Answers

Are you a Samsung Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...