Question about Sharp AL-1651CS All-In-One Laser Printer

5 Answers

Cannot print , paper cuts from the tuner & fuser

Error code L1-00

Posted by on

  • AlisonA May 01, 2008

    My printer shows an L1-00 error. Unplugging it, as suggested in the manual, does not work. It worked perfectly for 2 years except for a few minor problems. Suggestions?

×

5 Answers

There is a small plastic knob to lock and unlock the glass piece. I tightened it and it fixed the problem.

good luck

Posted on Sep 26, 2008

Yes I too have this problem, but I corrected it.

If you tighten the screws. it will work.

I have had this copier apart a few times. I must have3 not tighened the screws enough. it only took two days to figure this out. must not have been tight enough and head could not seat right.

Posted on Sep 12, 2008

There is a big gap on the left-hand side of the printer, where printed pages come out. If you stick your head down and look at the "roof" of the gap, you'll see a clear knob that locks the scanning head for transport. Turn the knob towards the front of the printer and it should clear this error code. (Source: Sharp AL-1651CS Service Manual.)

Posted on May 25, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 724 Answers

Yep AL 1651ch had an error L100 every time it was turned on and warmed the lamp. The head did jog a little and the cable was secure not binding and the transport lock was released. Weird all the shops said it can not be repaired. So did sharp and did say it was to old of a machine even though it was purchased 2 years ago and still in warranty. The just did not deal well.
I made sure the machine was unpluged, I removed the four scews at the 4 corners of the glass top and removed it exposing the scan had. I moved the scan head by hand, at first it felt tight on the tracks. Moving it down half way I took a small piece of paper and folded it so it would stand on end a half inch high and placed it in the way that the head motion sensor would see it. I powered it up and it was moving back to its start position and found the paper, jugged and then lamp off and error light again. That told me the motor was working the sensor was sensing and the drive mechanism was OK. It had to be a false sensor error. I reinstalled all the toner parts and cleaned the electrical contact adjasent to the drum front door. I gave up and put it back together tightening the screw. I turned it on again to give it a last go as it was cycling I continued to press the number pad and the scan buttonn to see it it can be confused. They only made a continued beeping sound each time I pressed a button quickly. I do not know what I did but the combination of things I did made it work to everyone's supprise.
I hope this will help because I believe that these companies need a good flushing and put in people that care to keep the customer and not give them a run around. We should go USA products but the Trade agreements are not in our total favor in this catagory

Posted on Jul 23, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have tried this in the past when that knob must have gotten bumped and it did work! However, I turned it to no avail this time. Thanks though. I'm afraid it must be something more serious.

Posted on May 29, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my Konica Minolta 1690MF have a fuser jam error whenever I print in color?


Everything you checked sound good. Might be printer software problem, and needs to be re-flashed. Software only available from secure web site that a technician would have, see what it cost if to much buy a new one with extra bells and whistles !

Jun 18, 2014 | Konica Minolta magicolor 1690MF All-In-One...

1 Answer

Media jam fuser


replace the fuser unit. and replace the transfer roller and belt,

Jan 30, 2014 | Konica Minolta Magicolor 2530 DL Laser...

1 Answer

Konica Minolta 1690MF causing Fuser Paper Jam error when printing color. Does NOT happen when printing black and white. (Paper is genuinely stuck entering the fuser). Why is the problem happening for...


I was wondering if the original poster of this problem found a solution. My printer does the EXACT same thing. B & W printing is perfect. Any color print jams in the fuser. The printer feeds the paper too far (from thin copy paper to cardstock) so that the top of the page is cut off. Konica sent me a new fuser but that did not solve the problem. Again, this only happens when printing any page that has color on it (even a document with only one letter in color). B&W printing is unaffected.

Aug 27, 2013 | Konica Minolta magicolor 1690MF All-In-One...

1 Answer

Lexmark C772n - 127.07 Service fuser error


I searched the Technical Manual and there is no explanation of the code. The user manual simply says there is a printer failure. They ask that you turn the printer off, wait 10 secs and then restart. Then call 1-800-LEXMARK and they will tell you about the code.

Given that your printer is saying Service Fuser, it is highly likely the fuser is ready for replacement. The fuser is the component that heats to high temperature to fuse the toner to the paper and complete the print cycle.

Aug 12, 2009 | Lexmark C762 Laser Printer

1 Answer

Getting code H 3


The printer repair guy just left. I'm paraphrasing what he told me:

The Sharp MX4501N was displaying the error: H3-04. This does mean that the printer was reading an above average temperature for the fuser, for some reason.

He said that in his experience, 90% of the time, this is due to power surges/spikes and not an actual incident of the fuser over heating. A good surge protector isn't normally enough and he recommended that we look around for a cheap UPS to condition the power.

Other things that can cause a higher than average reading of the fuser can be caused by paper jams, where a piece or pieces of the paper are lodges inside, insulating the fuser and restricting air flow to the internal compnents. Printing 15-25 blank sheets through the copier can usually dislodge these. If not, call for assistance.

In order to clear the error code (H3-04) from possible powewr surges/pikes, I was given the following code: #P, *, C, 1,4 PRINT
This will remove most of the codes restricting printing to the copier, however, should the code reappear, contact customer service and arrange for a visit from the local repair person.

I hope this helps anyone else who may run in to the same problemThe error: H3-04. This does mean that the printer was reading an above average temperature for the fuser, for some reason.

90% of the time, this is due to Power surges/spikes and not an actual incident of the fuser over heating. A good surge protector isn't normally enough and recommended that we look around for a cheap UPS to condition the power.

Other things that can cause a higher than average reading of the fuser can be caused by paper jams, where a piece or pieces of the paper are lodges inside, insulating the fuser and restricting air flow to the internal compnents. Printing 15-25 blank sheets through the copier can usually dislodge these. If not, call for assistance.

In order to clear the error code (H3-04) from possible power surges/pikes, I was given the following code: #P, *, C, 1,4 PRINT
This will remove most of the codes restricting printing to the copier, however, should the code reappear, contact customer service and arrange for a visit from the local repair person.

I hope this helps anyone else who may run in to the same problem

May 11, 2009 | Sharp AR-5316 Advanced Digital Imager...

1 Answer

ERROR CODE #021


Try a new toner cartridge. If that doesn't take care of the problem, it's the fuser.

Apr 08, 2009 | Panasonic Panafax UF-550 Plain Paper Laser...

1 Answer

Paper Jam? Print quality


If the toner wipes off the printed pages, then the fuser is the problem....not hot enough or enough pressure to heat the toner to the paper. I would try to reseat the fuser...make sure it is making good electrical contact. I have also seen the paper actually wrap around the fuser roll, which would cause the same symptoms...be careful removing the paper if that has happened...the fuser roll can be easily damaged !

Jan 22, 2009 | HP LaserJet 2840 All-In-One Printer

1 Answer

Error Code 155: Fatal Error


Looks like a fuser error-

re-seat fuser
check for paper scraps, etc in fuser and printer.

Service call
155: Error
Defective fuse
cutting of fuser
Is the fuser installed correctly?
Does the error recur?

Reinstall the fuser after its
connection connector is cleaned

if error still exists-
Turn on the power supply again
Replace M32 board after check
the cable connection.

Jul 29, 2008 | OKI KIT-C3530N MFP LASER CLR P/S/C/F USB...

1 Answer

Error code E00003-0000


The film (plastic) film is probably torn from a piece of paper that got jammed between the upper and lower section causing an overtemp lockout condition.
1. Remove left paper door.
2. Remove conector rear plastic(black) and fuser shields(2) screws holding fuser cover shield and unplug (3)connectors,2on the rear and a small one on the front lower right of fuser unit
3. Remove (2) assemlbly mounting screws one at rear and one
on the front sides.
4. remove unit and purchase new complete unit from cannon
5.Installed new fuser by reversing above steps.

May 28, 2008 | Canon (6981A002AA) for imagerunner 2200,...

2 Answers

49. 2F05 SERVICE ERROR


It is probably both the fuser and the firmware.
Power Off/On and see if the firmware issue goes away. From the control panel go to the Diagnostics Menu and select Print Event Log. It will give you a list of errors and what they pertain to, along with the page count when the event occurred.
Open the duplex pan (at the front of the printer, open the paper tray, and push the green button on the right in the tray cavity) and check for any small piece of paper that may be in the path. Verify that the hinge of the pan (where it connects to the printer chassis in the rear below the fuser assembly) is attached and not off its hinge. This can cause duplex jams. Additionally verify that the rear cover is not broken as the printer uses this to turn the paper.
Behind the rear cover is the fuser assembly. It may have a torn fixing film sleeve at one end or it may be contaminated, which can cause your image problem. It covers the ceramic heat element and sits above the lower pressure roller. One way to verify if the problem is the fuser is to print something from the control panel (like the configuration page located in the Information Menu). When the paper is under the cartridge but has not entered the fuser power off the printer. If the image mark is on the page its not the fuser because the paper hasn't gone there yet (try a new cartridge) if it is not on the page then the problem is the fuser.

Feb 04, 2008 | HP LaserJet 2430dtn Printer

Not finding what you are looking for?
Sharp AL-1651CS All-In-One Laser Printer Logo

256 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sharp Office Equipment & Supplies Experts

k24674

Level 3 Expert

7993 Answers

CheckitRight
CheckitRight

Level 3 Expert

1362 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Sharp Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...