Question about Bosch 24 in. SHU43 Built-in Dishwasher

1 Answer

Our dishwasher now blows a fuse when it is plugged in.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 19 Answers

Check the wiring into the dishwasher and see if there is any frayed or exposed wires touching. If you lay down in front of the dishwasher and listen, you may hear a hissing noise before the circuit trips. This is indication that wires are touching and should be re-spliced.

Posted on Jun 10, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi dishwasher starts then blows fuse in plug so far into cycle leaving dishwasher full of water


Unit blows fuse because it is using power beyond specs. Something has to be binding and slowing down the motor to cause this. Check motor bearings, mechanism, etc.

Jun 30, 2016 | Gorenje Dishwashers

4 Answers

Kitchenaid Dishwasher thermal fuse keeps blowing


if your fuse is blowing often i would suggest you to move your washer to a different place and try a different plug point.

there may be some fault with your power.

try to sort it out step by step.

thank you

Sep 17, 2008 | KitchenAid 24 in. KUDI01TJ - Multiple...

1 Answer

Keep blowing fuses


This means there is water collected on the base of the dishwasher cabinet under the bottom drawer. You will need to disconnect the dishwasher mains plug and take the bottom drawer out to dry the base out. Follow instructions in this manual (page 7 step 2) to remove the drawer.
Fisher Paykel DishDrawer Installation Instructions ManualsOnline com

Jan 08, 2014 | Dishwashers

1 Answer

Dish washer blows the switchboard fuses have to un plug it


Please clarify if the dishwasher had completed the wash cycle before the fuse started blowing up. It is likely there is flooding at the base of dishwasher which causes the mains fuse to blow. YOu will have to take the bottom drawer out to check. see this video on how to take drawer out. The steps are shown half way through the video. Make sure the mains plug is taken out from the socket before you handle the dishwasher.

Feb 05, 2013 | Fisher and Paykel 23 in. DD603H SS...

1 Answer

I plug in my dishwasher and the fuse blew in the socket any ideas shall I try again with another fuse?


No it sounds like a fault. Did the fuse blow immediately or during the program. A multimeter should be used to test for short circuits.

Jan 24, 2010 | Dishwashers

1 Answer

Everytime we switch on at the plug, the fuse is blowing


check wheather before switching on the cycle it's going means
1)problem in your main supply to board.

if it is blowing after switching on the cycle before starting the washing means
1)problem on the heater.

if it's blowing after washing cycle means
1)problem in the wash pump/heater.

Jan 08, 2010 | Hotpoint 24 in. FDW60 Free-standing...

1 Answer

Dishwasher


There is a short there, in control panel circuit board,that's why your fuse is keeps blowing.Trace the electrical connection from down to up to control panel board. Check for short capacitor and diode..Feel free to ask whatever the result..

Hope this may help you;


DON'T FORGET TO RATE;

Sep 03, 2008 | Indesit 18 in. D41 Slim-Line Free-standing...

1 Answer

Diplomat dishwasher blows fuses


I would disconnect the heater then run the unit.If it runs the heater is bad,if the fuse blows again the motor is most likley bad.make sure there are no water leaks.let me know.happy holidays

Dec 05, 2007 | Dishwashers

1 Answer

The fuse in the plug keeps blowing. Initially it would run for a while - sometimes 3 or 4 cycles - before blowing. It now blows the fuse the second that I plug in to the socket, even with the on/off button...


Lower the outlet hose into a washing up bowl, it should then Drain. Check the heater to see if it is earthing you get to it by removing the right hand side panel.

Nov 28, 2007 | Hotpoint 24 in. FDW60 Free-standing...

1 Answer

Blowing fuse


What exactly happened to your machine, before facing this problem?

Aug 27, 2007 | Hotpoint 24 in. DF55 Free-standing...

Not finding what you are looking for?
Bosch 24 in. SHU43 Built-in Dishwasher Logo

Related Topics:

244 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bosch Dishwashers Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

prem mathew

Level 3 Expert

662 Answers

bosch5

Level 2 Expert

157 Answers

Are you a Bosch Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...