Bottom to Black & Decker Landmower

Something has the motor unable to turn. Do not turn on till you locate the source of the problem lest you burn it out.

you should get a blade at any hardwere store

Try removing the blade. If the mower runs smooth, replace or balance it.
If not, the mower shaft may be bent. Did you hit something hard with the blade?

Gary

Does the mower sound like it is running at full speed? Have you double checked that the blade was not installed upside down?

slide it over the blade ,, so that it sits between the blade base and the pitcher bottom

Hey i found this for you i might help. Click on the link at the bottom!!


How to Sharpen a Black and Decker Hedge Hog Maintaining the sharpness of electric timmers can made landscape trimming easier with beautiful results. Electric hedge trimmers make trimming hedges and bushes easier and quicker than using manual hand-powered trimmers. Electric trimmers, the most popular type in the U.S., cost less and require less maintenance than gasoline-powered models. Electric trimmers are used most often by homeowners with the Black and Decker Hedge Hog series being very popular. While they are not premium products, electric trimmers like the Black and Decker Hedge Hog trimmer can keep trimming reliably for years with proper maintenance, including sharpening the blade's teeth.
Difficulty: Moderately Easy Instructions Things You'll Need

• Work table
• Two medium size clamps
• Dremel tool or similar hand-held multi-purpose tool
• Grinding wheel attachment for hand-held tool.
• Dremel 971 (or similar) aluminum oxide grinding sharpening stone with a tip small enough to cover the flat facet of a Hedge Hog blade tooth

1. • 1 Unplug the electric trimmer before trying to sharpen the teeth.
     
   • 2 Clamp the electric trimmer to the work table using two clamps if necessary so the Hedge Hog is firmly held down with the blade teeth accessible over the edge of the work table.
     
   • 3 Insert and secure grinding tip in hand-held multi-purpose tool.
     
   • 4 Maneuver the grinding tip so it is perpendicular to the facet of the Hedge Hog tooth.
     
   • 5 Sharpen teeth in one direction, being careful to try and maintain the same cutting edge angle on the sharpened tooth of no less than 35 degrees.
     
   • 6 Make same number of grinding passes/grind the same length of time a few seconds on each tooth.
     

Tips & Warnings

• This task should take about 15 minutes.
  
• Keep a light touch; too much force can break the grinding surface.
  
• For best results, insert the sharpening bit slightly less than all the way into the tool.
  

Read more: How to Sharpen a Black and Decker Hedge Hog ' eHow.com http://www.ehow.com/how_7163131_sharpen-black-decker-hedge-hog.html#ixzz1XsAosvvl



http://www.ehow.com/how_7163131_sharpen-black-decker-hedge-hog.html

I have the Black & Decker Shortcut food processor Model CFP10 and it has a broken bowl. I would prefer to replace the bowl but haven't found a source. So I would be willing to sell the good parts: Food Pusher, Food Chute/Cover; Food Fingers/ Reversible Disc, Disc Stem, Knife Blade. Make me an offer and e mail me at:
[email protected]. I'll accept Pay Pal or certified checks.

the shear pin has broke on the drive shaft put a new one in.

I use a dremel with a sharpening stone, if u don't have one you can also use a power drill with a small sanding disk (1 inch) and course sand paper (30 or 40 grit). or you can use a bastard file. its too tight to use any kind of angle guide so just take your time and do it by eye. it shouldn't take much to get them sharp enough to do the job, over-sharpening is unnecessary and dangerous, and will make the blades dull faster. sharpen all the free blades, top and bottom, then start the trimmers to advance the blades to free up the sides you couldn't get. i use a light penetrating oil to clean the blades first, then lithium grease spray to lubricate.

possible broken armature & magnetic ring.mower need max repair.