Question about Pioneer Car Audio & Video

Open Question

Pioneer avic1xr screen gone blank and some buttons from the panel are not working

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ca900 radio wont work - the radio lights up as expected but the main area that normally displays what station yo are listening to is blank. No sound comes out except from the beeps when pressing buttons on...


Hello Dan, have you tried to reset the unit using the reset button behind the front panel? also try to clean the panel metal contacts, clean them using a cotton swabs or an handkerchief wet with alcohol, both side (main unit & detachable panel)

Oct 23, 2013 | Car Audio & Video

1 Answer

My touch screen isnt working properly on my pioneer avh 57000


you by-passed with a toggle switch? correct? pioneer older units need to have a ground introduced each time power is supplied,,,on off on,use a two-way toggle switch

Jan 27, 2013 | Car Audio & Video

1 Answer

I have a pioneer deh 1300. I have all the wiring connected but there are no settings for the amp to turn on. I have gone thru and double checked the wiring and all the fuses on my amp also. Any ideas on...


make sure the amp has a good earth connection. is the light on the amp working and what colour is it? push in and hold the volume button their should be some settings there for it, also check that the deh 1300 is amp compatible

Jul 21, 2011 | Car Audio & Video

1 Answer

I have a pioneer cxe2187 car stereo/navigation system. The GPS is stuck at the last input destination and wouldn't accept any new input. What should I do to reset the system?


For the pioneer cxe2187 car stereo/navigation system, there is a very tiny reset button on the front of the screen just below the bluetooth light. Push it with the end of a paperclip and hold for 10 seconds then release. It will reset the system without loosing anything!!

Apr 09, 2011 | Pioneer Car Audio & Video

1 Answer

Pioneer car radio DEH-P6800MP. How do I put it on auxillary?


1 press function repeatedly until you see aux on screen select aux .
2 press select aux on or off turn on aux
once you turned on aux fucntion when you need to use it use the source button to change radio to aux here is a link to its in german and english . http://pioneer.ipapercms.dk/Manuals/DEH_P6800MP_XRD7099_manual/

Dec 23, 2010 | Car Audio & Video

1 Answer

No pic when ipod plugged in


Have you gone through the settings on the d3? Most pioneers have a setting in the setup menu to turn on ipod video.

May 11, 2009 | Car Audio & Video

1 Answer

Faceplate won't display


if its a fold down display the ribbon cable is gone, repair shop job) it goes from the front panel into the motherboard of the stereo and after a while with you opening and closing the display the cable eventually breaks, if its not a fold down display clean the contacts of the front panel with meths and a cotton bud, if still no joy take it to repair shop,

May 09, 2009 | Car Audio & Video

1 Answer

The screen on my 3 month old Blaupunkt Hamburg MP68 has suddenly gone 'fuzzy' and then blank, apart from this all works fine! Is there a simple solution, which I can do, or does it have to be sent in for...


The only thing you can do is to check if the flex board between the screen and the video IC is bad. However I would advise you to send it in for repairs.

Thank you,

Shuttle83

Nov 07, 2008 | Car Audio & Video

1 Answer

As others on this site have experianced ,I am unable to set the time on my pioneer deh-2050mp. the user manual gives a description but it does not work. even the staff at the store where purchased were...


We found the solution on the Pioneer WebSite. You have to press the source button to off then press it again and hold it in until the clock comes up and flashes then you can set the time. The function button as per the instruction manual has nothing to do with it!

Sep 28, 2008 | Pioneer Car Audio & Video

1 Answer

Avic z2 2nd one installed in H2 by professional. Unit will boot up about every 5th time. Last music source still plays thru Otherwise only Pioneer logo or blank screen. Reset does not help. Very...


Go to Pioneerelectronics.com...there is a firmware upgrade which solves this issue. You can eith call them toll free and they will send you a free disc, or you can download onto CD-R and update yourself. Take care.

Chris

Aug 20, 2008 | Pioneer Car Audio & Video

Not finding what you are looking for?
Car Audio & Video Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pioneer Car Audio & Video Experts

Michael Kovalik III
Michael Kovalik III

Level 2 Expert

117 Answers

The Knight
The Knight

Level 3 Expert

69878 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Pioneer Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...