Question about NetGear DG834G Router

2 Answers

Can get full signal connection but ie does not display

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 6,966 Answers

Hi,

Pls verify that:
1. in your Control Panel/Internet Options/Properties/Connection tab/LAN Settings button, the "Automatically detest settings" is checked and that both "Use automatic....." & "Use a proxy...." are both unchecked;
2. in your Control Panel/Internet Options/Properties/Advanced tab, both "Use HTTP1.1" & "Use HTTP1.1 through..." are both checked;
3. in your Control Panel/Network Connections/Wireless Network, right click & click on Properties, highlight "Internet Protocol (TCP/IP), click on Properties button, both the "Obtain an IP..." & "Obtain DNS..." are ticked.

Additionally, pls type "cmd" in Start/Run. In the next window type "ipconfig /flushdns". To verify if your router is assigning to your PC IP numbers, you can type "ipconfig /all" and numbers should show in your WiFi networking. Just pls verify that the Default Gateway is 192.168.0.1 and that your PC's assigned IP address is 192.168.0.X (where X is a number between 2 and 254).

You can also verify if your PC can indeed connect to the router by typing ping 192.168.0.1 and numbers should show.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards.

Thank you for using FixYa.

Posted on Apr 16, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 221 Answers

If it's in the Warranty Period, take it to the Service Station and if it's not, take it to an outsider expert.







Sahaja Yoga is the Mahaa Yoga and is the Only Solution to all the Problems of World.

Posted on Apr 16, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My laptop and my iphone indicate that my wireless-g broadband router is putting out a wireless signal; but neither accessory works on the network, even though the bars are entirely full on the devices.


The bars on your laptop or iPhone means that you are connected to the router! Not necessarily to internet. Your internet depends on ISP Internet service provider and modem which connected to your router. To check if you have active internet connection connect your laptop directly to modem provided by your ISP with ethernet cable and try to open a internet browser IE or Safari or Chrome or Firefox and open a webpage! If you are able to connect internet by this mean you have internet connection active. Now disconnect your lap top from modem and connect modem to your Linksys router using WAN port of LINKSYS! Its good to power off and power on (power cycle) once on modem and router to make it work!
good luck!

Sep 14, 2011 | Linksys Wireless-G Broadband Router

1 Answer

My old PC with Windows XP has a wired connection to WGR614 router and internet connection runs at 9Mb. My new Intel i3, Windows 7 laptop with wireless connection runs at 600Kb and invariably has IE...


It sounds like you may have another wireless network or some other wireless device that could be causing interferance.

1. Do you have a cordless telephone or baby monitor in the house... if so, is it near either the router?

2. If you do a search for wireless networks, can you see other networks? If you can, see what channel they are using, you will need to set your wireless channel to at least 5 higher or lower than at least the strongest signals (so if you see another on channel 1, make sure yours is on at least channel 6). This should prevent channel interference on the wireless network.

Hope that this helps!

Oct 17, 2010 | NetGear WGR614 Wireless Router

1 Answer

I cannot access a connection to the Linksys with my Kindle. What do I do now? -- Thank you!


I am going to assume that you have a valid wifi signal that is working with other systems in your house.

Your router will broadcast a signal unique to your system (even in default mode, ie right out of the box)
Take your kindle and go to the settings screen. Select WIFI ON.
It should detect any available networks in your area.
Yours should be at the top (strongest signal) (unless you have a special SSID)
Choose the wireless connection you want, and select connect. The Kindle (as in any device) will try to connect to the chosen wifi. If yours is a password protected WIFI system, you will be prompted for the password.
Once the Kindle negotiates the connection, it is will say connected, or it will display the fault.
We can deal with the fault if there is one...

good luck and don't forget to vote!!!

Sep 28, 2010 | Linksys Wireless-G WRT54G Router

3 Answers

Cannot connect wirelessly


You need to setup cisco page, with your ISP. Your setup name and password must be same for all computers. All computers for this installation must connected by wire at the beginning. And make sure you enable the wireless options on Linksys page. READ HELP form Linksys main page.

Aug 12, 2009 | Linksys Wireless-G WRT54G Router

2 Answers

I have a WCG200 linksys but can not go onto internet.


from what i have read, your router is broadcasting a signal, and your modem has an open and active internet gateway.

pls make sure that the connection from the modem to the router are correct. the modem should be connected in the port with the label internet. you may have to reset your modem AFTER you have connected the wireless router to allow the router to be assigned an ip. now with the wireless router and broadband modem connected, you can connect to the network and access the internet. pls repost if you hit any snags
GOOD LUCK and PLS rate this post.

Mar 18, 2009 | Linksys WCG200 Router

2 Answers

Internet page does not fully display


There are two reasons
1) the firewall on Dell preventing it from opening up
2) IE needs to be uninstalled and reinstalled

Try the later

IE closing immediately indicates that one of the files for IE is corrupt or broken or missing. Try and repair the IE file/files that is/are missing/corrupt

Dec 28, 2008 | Linksys WRT160N Wireless Router

1 Answer

Computer stopped receiving wireless router signal


In this order: 1) Turn off all PCs and printers connected to the router. 2) Unplug your router's power cord. 3) Unplug your modem's power cord. 4) Wait for at least 2-3 minutes. 5) Connect the modem's power cord and wait for at least 2-3 minutes. 6) Connect the router's power cord wait for at least 2-3 minutes. 7) Turn on each PC separately and wait until it is completely finished booting before turning on the next PC.

If you still do not have connectivity, read the manual and change the channel of the modem. YOu may be experiencing some RF interference, ie microwave, wireless phone system etc...

Oct 29, 2008 | Linksys Wireless-G Broadband Router

1 Answer

IE Dosen't Display


I'm assuming you are trying to connect to your Belkin router? If so, the address for a belkin router is 192.168.2.1

May 08, 2008 | Belkin Wireless G Plus MIMO (F5D9230-4)...

1 Answer

Wireless router dynamode


areejshaukat,

if ur laptop detect full signal from ur router, click on the signal and let ur laptop connect to the signal..coz even ur laptop detect the signal,it doesnt auto connect,so u hve to connect it manually..

Apr 07, 2008 | Computers & Internet

1 Answer

Router connections


If you have a laptop in home 2 that is able to connect with NO issues whatso ever I would almost think its a security issue... Do you use the same kind of encryption on both home 1 and 2? (ie WPA or WEP)

Dec 31, 2007 | Computers & Internet

Not finding what you are looking for?
NetGear DG834G Router Logo

Related Topics:

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top NetGear Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2260 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18344 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Are you a NetGear Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...