Question about Humminbird 595c GPS Receiver

1 Answer

Recently purchased a hummingbird 535 fishfinder,for fishing in france in june.unfortunatly will not be allowed to permantly fix the transducer to the boat, is there a temporary bracket or similar i can purchase,cheers neil

Posted by on

1 Answer

I have seen a suction cup for the eagle brand depth finders maybe it will fit a hummingbird

Posted on Jul 13, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I need to connect a Garmin 160 transducer to a garmin 120 fish finder


Hi,

If I may inquire, how many pins on the transducer and on the fishfinder.

Hope to hear from you and pls post back the requested information.

Good luck and kind regards. Thank you for using FixYa.

Sep 17, 2008 | Garmin GPSMAP 188 Fish Finder/GPS Receiver

1 Answer

Is the transducer for a hummingbird 386ci the same as for the 688 ci?


Hi Cliff

I believe your best bet here would be to contact Hummingbird directly. There's the contact page. Hope this helps you out.
-Steve

Contact Us

Nov 10, 2014 | Hummingbird GPS Devices

1 Answer

No transducer


Make sure the plug that gives this unit power is secure. Also I think this device has a 2ft branch that goes to the ducer. Make sure that's right too

Apr 10, 2014 | Garmin FishFinder 240 with Transom Mount...

1 Answer

MY RAYMARINE A65 CHART PLOTTER/ FISHFINDER HAS NOT BEEN WORKING , THE CHARTPLOTTER WORKS FINE , BUT THE FISH FINDER WONT PULL UP BOTTOM OR ANYTHING . I LOOKED AT THE LITTLE BOX THAT CONNECTS TO THE...


Likely your DSM25 (that little box that connects the transducer to the display) will need to be rebuilt. The red LED is saying that there is an internal fault with the unit. You would need to send the unit in for repair through Raymarine (as there really is not anyone else who can do it), and they would have to replace the main circuit card in the box. I believe that they are charging either $150 or $175 to repair those now... but likely the only way you will get that one to work again.

Jul 27, 2010 | Raymarine A65 Combo GPS...

1 Answer

I have had a Garmin 400c Fishfinder on my 20? Intruder for about 2 yrs. While fishing in the ocean last fall , I started getting intermittent false shallow readings on the unit (but the target depth...


Hello. Go to any autoparts store and purchase an aerosol can of electrical contact cleaner. It replaces ozone-depleting CFC's, trichloroethane, HCFC's, perchloroethylene and other carcinogenic chlorinated solvents. It will clean your contacts of corrosion and remove any and all moisture from them. And it will protect them well into the future. I use it everywhere on my craft, and on the trailer.
Spray the product, let it sit for an hour and then spray again. Use a cotton swab to remove any visible crud. Regards, Joe

Jan 12, 2010 | GPS Devices

2 Answers

Garmin Fishfinder 160 will not display bottom contours and does not display depth continuously.


Change your setting from saltwater to fresh water even if you fish in sea water,your transducer is a 00/200KHZ and not a 50/200KHZ.
Good luck
Willem

Mar 01, 2009 | Garmin Fishfinder 160 GPS Receiver

1 Answer

Navman 4500 fish finder w/transom mount transducer


I finally got an email reply from Navman. If the unit is less than two years old (mine is not) they will repair it. If it is over two years old, or if you can't prove that it is less than two years old, you can ship it to them and they will repair it for the low, low price of 355 US dollars.

Pretty nice of them since it appears these units are highly problematic isn't it? I am wondering if they guarantee their fix, or just have you on the hook for another 355 dollars later.

Good Luck Everyone,

Walt

Sep 20, 2008 | Navman F4100SX Fishfinder - W/ Transom...

1 Answer

False fish readings


False fish readings are commonly caused by electrical interference such as alternator noise, and by air bubbles flowing across transducer.

For starters make sure your fishfinder is on an independent circuit and not on one powered by your ignition switch. In other words, you should be able to turn your fishfinder on, even though the engine is turned off. Ideally the fishfinder should be wired directly to the battery with an in line fuse.

Try running the boat at a speed slightly higher than trolling speed, then kill the engine, as the boat slows down to trolling speed do you still see false echos? If yes then the problem probably lies with how the transducer is mounted, or where it is located on the hull.

If you don't see the false echos when the engine is off, it may be necessary to reroute the transducer cable to keep it away from the boat's ignition wires. You can get transducer extension cables if necessary. Also there are filters that you can buy that suppress alternator noise buy attaching between the battery and the engine.

Another common cause of false echos from electrical interference is a transducer cable that has been cut and spliced.

I hope this information helps. Please reply if you have any questions about my response.

Feb 25, 2008 | GPS Devices

Not finding what you are looking for?
Humminbird 595c GPS Receiver Logo

323 people viewed this question

Ask a Question

Usually answered in minutes!

Top Humminbird GPS Devices Experts

Steve
Steve

Level 3 Expert

688 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

yadayada
yadayada

Level 3 Expert

60779 Answers

Are you a Humminbird GPS Device Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...