Question about Printers & Copiers

1 Answer

Kodak ektaprint 90

We are church looking to sell our ektaprint 90e. It hasn't been used for a few years and someone put an access code on the machine. They are no longer affiliated with the church.

Is there a procedure to manually override the code to gain access to the system? We would like to evaluate if this is saleable or if we should just haul it to the dump.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Printers & C... Expert
  • 287 Answers

Hello tldant,
Wow, that is a very good copier although quite old.Unless the wheels have been run off of it its a keeper. I used to work for Kodak when they marketed this machine and I was a service tech for them. Great machine. I had one that had 6 million copies on it and was still worth keeping. Now to the point. Unfortunately this copier has a physical "jumper" inside the back panel that has been removed which causes the copier to expect some type of additional action to provide access to the device. There were several ways to gain access (access codes, external controllers, even a card like a credit card) to the copier once this jumper was removed. The jumper is actually a small connector that fits on the end of a wiring harness that basically completes a circuit to tell the copier to be ready. Without the jumper, the copier is waiting for an external device or virtual device to "complete" the circuit. It has been over 10 years since I touched one, so I am sorry that I can't recall the exact location of the wiring harness. However,typically the "jumper" (a small connector with a mere loop of wire from one pin to another) is tied near or onto the place it belongs. So I guess my point is that the copier is worth the time it would take to remove the covers and inspect the wiring in hopes of noticing a stray connector that is just dangling. I wish I could be of more help, but maybe I have been some help. Take care and good luck. :-) ................spinal........

Posted on Apr 19, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Phaser 7400 squeaks while printing


id try lubing the feed rollers well the metal bars where they contact the chassis and lube gears and stepper motors. its been awhile since ive had my phazer. i traded it last year to my church pastor but try that. radio shack sells a teflon lubricator part no. 64-2301a and im certain amazon also sells them. ONE drop goes a LONG way. its also a miracle worker for pc fans, and household appliances as well as automotive where its not high heat. even bearings.

hope this helps you a tad sorry i cant be more of a help here but thought id pass a few personal experience in fixing electronics/mechanical tips along.

Dec 10, 2012 | Xerox Phaser 7400/DX Laser Printer

1 Answer

Is there any place in nh to get a kodak copier repaired


Hello hd, I assume you are referring to New Hampshire. Although I am a simple **** from Tennessee I may be able to help you. Kodak's appetite for the "office imaging" market began to die on the vine far earlier than the towel was officially thrown in. Forgive my longwindedness but this will flesh things out for you and provide you with more options to to get service on your copier. The IS50 was actually made by CANON (which you may already know) and was I believe the last copier Kodak marketed during it's 10 year joint venture with Canon. Fast forward, Kodak sold its copier division to DANKA. So you have 3 options. Kodak.........(zip)......Danka.....(marginal)......Canon..........best bet. Please consider this. The IS 50 is darn good copier. But it's lifespan(legally) has expired and NEW parts might be close to impossible. A fouth option might be to find a "Joe's Canon Copier"shop, like a 3rd party CO. as they willl buy copiers at auctions and from leasing companys etc,,,, .There is a huge market for this and they tend to have decent techs as they have low overhead and max profits as they roll a NEW copier into a church and merely ask for a cost per copy with no strings attached. They buy something for nothing (copier) and every time the START button is pressed their bank account increases. Now, how to determine whether Bill or Joe or Bob's copy service is the one you want is a toughie. Canon does have a rating for companys that are not certifed dealers,......but ....they will sell parts to.I don't know the whole story on that but I would use that as a benchmark. Sorry to ramble, I just hope I helped. Live long and happy paper jam. SPINAL

Feb 09, 2011 | Kodak ImageSource 50 Copier

1 Answer

The Printer is using IP - Lan up. Whenever a user wants to send print job to the printer, a message is displayed on the panel of the printer which reads 49.2f9d error


The P3005 is known to have problems with a chip on the formatter, gives various errors to include the 49.2d9d, blank display and others. HP has not issued a recall or service advisory but is fully aware of failure of the chip on the formatter. Repair for this is to print a configuration page, replace the formatter board, bring the machine back up in service mode and put in the correct serial, service code and page counts into the new formatter's nvram memory.

Liberty Parts Team at lbrty.com has refurbished formatters at reasonable pricing with no return core to worry about. The PIN needed to access the service mode is 10300506.

Other problems with the P3005 are grinding in the fuser area, correctable by removal of the fuser, replacement of the 4 accessable gears in the side (left as you look into the back) and the main gear on the fuser then put the fuser back in and should be good.

Service manual available for free at feedroller.com - down the left navigation bar near the bottom is an icon and link to service manuals in PDF. No need to make someone on ebay rich selling copyrighted pdfs.

Jun 25, 2010 | HP LaserJet P3005 Printer

1 Answer

Has a I54 code. goes on but goes into code after 10 seconds or so. Thanks Lawrence


there is a circut breaker switch in the back of the copier put it into (1)

Mar 19, 2010 | Kodak Ektaprint 95 Copier

1 Answer

The printer says i need to put in color ink cartridge.it is in and wont do anything


if the red light is still flashing then try and reseat both the ink cartridges and print head and make sure you use genuine kodak ink cartridges as there are retailers selling look alike and refilled ink cartridges.......if still the same problem then print head problem call kodak tech support they will replace it for you without any charge........

Jul 07, 2009 | Kodak EASYSHARE 5500 All-In-One InkJet...

1 Answer

Could not load software. Paper jam damaged print head.


Do the right thing, sell it on eBay but tell it like it is in the ad. Someone is bound to buy it and fix it.

May 12, 2009 | Kodak EASYSHARE 5100 All-In-One Printer

1 Answer

No red color


Call Kodak Customer service and request a new printhead. They do not sell them in stores.

You could try soaking your printhead nozzles in hot water. NOT TAP WATER OR DRINKING WATER. make sure the water is distilled or de-ionized. do not submerge the entire printhead just the nozzle plate on the bottom. you could also try distilled vinigar, or 90% rubbing alcohol. I would not recomend wipeing the printhead nozzles they are delicate.

May 17, 2008 | Kodak EASYSHARE 5100 All-In-One Printer

1 Answer

Kodak 5300


You have a few options. 1. Use the Printhead cleaning in the Kodak Software this is recomened way and the safest but will use ink each time. 2. Get a T-shirt or another type of cloth that wont leave lint, get some distilled or de-ionized water (tap will work but not as well) and mannually clean the printhead. To do this remove the printhead and look at it. you should only wipe with the nozzels groove. go with the grain not against it. you dont need to put alot of pressure. Place the nozzels on a wet area of the cloth wipe in the directions of the nozzels you can do this on a flat surface or use your fingers to press against. 3. Call kodak say your printhead is dead and you would like a replacement. They should not charge you for it because its not your fault that it does not work.

Feb 11, 2008 | Kodak EASYSHARE 5300 All-In-One InkJet...

1 Answer

Error code F-77-2


I cna't help unless you provide the make and model of the machine. From the looks of the number it could be a Konica but I need the model to tell you wat it means. Aloha,  Bill Monroe 

Nov 27, 2007 | Printers & Copiers

Not finding what you are looking for?
Printers & Copiers Logo

Related Topics:

300 people viewed this question

Ask a Question

Usually answered in minutes!

Top Printers & Copiers Experts

kakima

Level 3 Expert

96518 Answers

old marine
old marine

Level 3 Expert

1464 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...