Question about Kenmore 53701 Dehumidifier

1 Answer

Kenmore model # 25800-25801 Error code E1?

Dehumidifier coils freeze, and reading E1 error code... won't draw water.

Need help, unit is 2yrs old.

Posted by on

  • stacemoe Apr 17, 2008

    WOW, thank you very much 'fixum1'. appreciate the answer very much. also, didn't realize it was still under warranty, so that is also a great answer!

    happy fixin',
    stacey

  • Anonymous Mar 13, 2014

    samsung dehumidifier e1 code, what does that mean?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,073 Answers

Unit has a sealed system leak call sears for tech support 1-800-905-9505 it is under warranty

Posted on Apr 17, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Freezing up and bucket not filling


Hi,

The coils you see on the back of your dehumidifier are the evaporator. When the unit runs, the coils get very cold. As the fan draws the room air over the coils, the humidity in the air condenses out of the air onto the cold coils. But, if the temperature of the air the fan draws over the coils is too cool, the humidity that condenses out of the air freezes on the coils. To remedy this problem, you can try any of these: Warm up the room the dehumidifier is in. Put the dehumidifier on a sturdy table (the room air is coolest near the ground).

Turn the unit off until the room warms up.
Good luck

Aug 19, 2010 | Kenmore Dehumidifiers

1 Answer

Freesing up and bucket not filling


Hi,

The coils you see on the back of your dehumidifier are the evaporator. When the unit runs, the coils get very cold. As the fan draws the room air over the coils, the humidity in the air condenses out of the air onto the cold coils. But, if the temperature of the air the fan draws over the coils is too cool, the humidity that condenses out of the air freezes on the coils. To remedy this problem, you can try any of these: Warm up the room the dehumidifier is in. Put the dehumidifier on a sturdy table (the room air is coolest near the ground). Turn the unit off until the room warms up.

Take care.

Aug 19, 2010 | Kenmore 5230 Dehumidifier

1 Answer

E1 CODE ERROR


E1 code for the primary humidity sensor behind right side grill. Unit MUST be unplugged from outlet. Take right side grill out, unplug sensor from wire socket and plug back. If no help, you need new sensor.

Dec 30, 2009 | Danby DDR451 Dehumidifier

1 Answer

My DANBY Dehumidifier model DDR4588EE has been working ok until it showed a E1 error code and since then it does not work properly. Any ideas please?


E1 code for the primary humidity sensor behind right side grill. Unit MUST be unplugged from outlet. Take right side grill out, unplug sensor from wire socket and plug back. If no help, you need new sensor.

Dec 30, 2009 | Dehumidifiers

1 Answer

Dehumidifier runs but doesn't produce water


Your dehumidifier has a circulating fan that draws the room air over the coils. If there's no air movement out the front or back of the unit, the fan motor may be burned out or stuck, or the fan blade may be broken. If so, you need to replace the fan motor or the fan blade.

Sep 04, 2009 | Kenmore 5230 Dehumidifier

1 Answer

P1 error


Your question needs to be answered in 3 parts:

1) As per the manual for my Danby Dehumidifier (Model DDR657EE), the unit may not turn on immediately when powered On (it may take a several minutes). So, generally, it would be normal in your case.

2) Danby's Consumer Help Line (1-800-263-2629) is always busy. So, I called their General number: 419-425-8627. The receptionist transferred my call to their Service dept. My call was answered in 2 minutes.

The Service Rep. described the following code for my dehumidifier model (DDR657EE):
P1 = Defrosting: the unit will go into Defrost mode periodically to ensure that the parts are working at the right operating temperature. It should be in Defrost (P1) mode for only a brief period of time. If the unit is in Defrost (P1) mode continuously for a couple of hours (or more), then you should call Danby Service for further assistance.

He had no documentation of a P2 code for my model.

He also described other General Codes (applicable to most Dehumidifier/Humidifier models):
E1 = Not enough water
E2 = Not draining
E3 = Water temperature too cool
E4 = Overflow Switch activated
E6 / E7 = Problem with Temperature Sensor

So, generally, if you see P1 periodically (for brief periods), then it would be normal.

3) Since your unit keeps running (continuously) and there is no water in the bucket, then you should call Danby ServiceI for additional assistance - it seems defective for this reason.

I hope that helps.

Oct 31, 2008 | Danby DDR2506 Dehumidifier

6 Answers

P1 and P2 error codes


Danby's Consumer Help Line (1-800-263-2629) is always busy. So, I called their General number: 419-425-8627. The receptionist transferred my call to their Service dept. My call was answered in 2 minutes.

The Service Rep. described the following code for my dehumidifier model (DDR657EE):
P1 = Defrosting: the unit will go into Defrost mode periodically to ensure that the parts are working at the right operating temperature. It should be in Defrost (P1) mode for only a brief period of time. If the unit is in Defrost (P1) mode continuously for a couple of hours (or more), then you should call Danby Service for further assistance.

He had no documentation of a P2 code for my model.

He also described other General Codes (applicable to most Dehumidifier/Humidifier models):
E1 = Not enough water
E2 = Not draining
E3 = Water temperature too cool
E4 = Overflow Switch activated
E6 / E7 = Problem with Temperature Sensor

I hope that helps.

May 25, 2008 | Danby DDR2506 Dehumidifier

3 Answers

CH1 IS SHOWN AS WELL AS THE BUCKET FULL LIGHT


I have a LG model LHD65EBL that first started icing up along the top edge during humid days. After several months of this, it finally stopped working and displayed CH01 with the bucket full indicator flashing.

I took apart the dehumidifier, removed the temperature sensor from the coil and rubbed it between my fingers. I then plugged in the unit and it started right up, confirming either a sensor or other circuit problem related to that sensor. For my model unit, I ordered sensor assembly #6877A30013L from RepairClinic.com for $21.75 + shipping.

When I received the assembly, I measured the new and old sensor with an ohm meter: new sensor = 5.5KOhms, old, defective sensor = 5.34KOhms. I installed the new sensor assembly and the unit is working fine.

Just because the bucket full indicator is flashing along with an error code does not mean there is a problem with the bucket full switch.

Dec 17, 2007 | LG LD65EL Dehumidifier

Not finding what you are looking for?
Kenmore 53701 Dehumidifier Logo

810 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Dehumidifiers Experts

Bill Long

Level 3 Expert

577 Answers

Cindy Wells

Level 3 Expert

4757 Answers

kakima

Level 3 Expert

96518 Answers

Are you a Kenmore Dehumidifier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...