Question about Car Speakers & Subwoofers

1 Answer

It is asking to enter a code of four numbers - Car Speakers & Subwoofers

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 20 Answers

What is.

Posted on Apr 14, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My battery died, so I needed to jump start my battery. When my car started again, my screen was asking for a four digit password. I think I entered the wrong number in one too many times, so now the...


  • You can try to disconnect the battery again for 5 minutes and then reconnecting it and see if that brings your screen back up. If it does not then your radio has gone into PUK mode. PUK mode is what happens when the wrong code is entered to many times. It's a lock that can only be overridden by contacting the manufacturer of your radio. This is a security feature. Good luck.

Regards, Tony

May 06, 2011 | Car Speakers & Subwoofers

2 Answers

Ulock code kdc-mp5028


Type 1
During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds (so that “…” disappears).
Then using your remote enter your code.

Type 2
Press the "Auto" button and "Track up" on face of radio at the same time. The four dash lines ( . . . . ) should "disappear".

Then using your remote enter your code.

Type 3
Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset key (preset keys are the buttons on face of radio for storing you "favorite" radio stations). "C" should display.
Then using your remote, enter your code.


Enter your number from the remote control unit. Your code number is 5227 (KCAR)

* Press numeric key “5” ( 2 times ) and press the Track UP/Next Track key
* Press numeric key “2” ( 3 times ) and press the Track UP/Next Track key
* Press numeric key “2” ( 1 time ) and press the Track UP/Next Track key
* Press numeric key “7” ( 2 times ) and press the Track UP/Next Track key
by Robotek

hope this helps...

Jul 30, 2008 | Kenwood Car Speakers & Subwoofers

2 Answers

I entered my four digit number i got off fords -- pressed the 5 button but stereo still not activating can u help


Post the SERIAL NUMBER found on the label on the casing and we will check to make sure you have the correct code.

It normally begins with M ++++++ or V ++++++

Mar 10, 2011 | Car Speakers & Subwoofers

1 Answer

GM Radio Locked but will not display codes by pressing 1&4 or 2&3


Does your GM car or truck Radio display LOC and does not turn on? Chevrolet, Buick, Pontiac, GMC, Cadillac, Oldsmobile vehicles used a theft system to lock the radio when power is lost. This system was used from the ealy 1990's to the early 2000's.
jQuery('.intro .thumbnail').each(function(i,e){ jQuery(e).find('img').one('error',function(){ jQuery(e).remove(); }); });
Instructions:
  1. If your radio displays the word LOC, you can retrieve a set of factory numbers in the radio that enable you to get a backup unlock code. If the radio says INOP, you will have to leave the key in the "ON" position, or let the car run for at least 1 hour before you attempt any unlock procedure. INOP means a secondary theft lock due to too many false attempts to unlock the radio.
  2. Looking at the face of your GM Delco radio, hold down the preset buttons 1 & 4 OR 2 & 3 (Depending on year and model) for approximately 10 seconds or until a set of 2 or 3 numbers comes up on the display. Write the numbers down.
  3. Next press the AM / FM button. A new set of 3 numbers will now show. Write these numbers down. You will then need to call a 1-800 phone number with these numbers to get the unlock code. There are many sites on the internet that can get it for you- for a small fee. Or, try calling your local GM Dealer and ask for them to do it. Many times they will do it for free. It only takes a minute.
  4. Once you have the unlock code, enter it by pressing the MIN button until the display shows the last 2 digits of the unlock code, then press the HR button until the first 2 numbers or shown. Then press the AM / FM button to enter the code. The radio will now display SEC, and normal function is restored.
Also, its possible that you need RESET your GM Radio; this is the procedure: While performing maintenance on your car, you may disconnect the radio from the battery in your GM vehicle. GM cars contain Delco radios that are protected by Theftlock, which locks the radio after it has been disconnected from a power source. Iit can only be reset and unlocked with a car-specific security code. Identifying the security code for your GM vehicle is the only way to reset the car radio and disable the Theftlock protection device. jQuery('.intro .thumbnail').each(function(i,e){ jQuery(e).find('img').one('error',function(){ jQuery(e).remove(); }); });
Instructions:
  1. Turn on your car. Your Delco radio will show "LOC" in the LED display.
  2. Press and hold down both the second and third preset buttons. Hold these buttons down for at least six seconds.
  3. Write down the two- or three-digit code that appears in the LED display.
  4. Press the AM/FM button on the radio.
  5. Write down the next two- or three-digit code that appears in the LED display. You should be left with either a four- or six-digit number. Turn off your car.
  6. Call the Delco radio automated customer support line at 1-800-537-5140.
  7. Press "1" and then press the pound sign. The automated voice should respond "Invalid code, try again."
  8. Enter the number 139010 into your phone and then press the "*" sign.
  9. Enter the four- or six-digit number you wrote down from Steps 3 and 5, and then press the "*" button.
  10. Write down the four-digit code given by the automated voice.
  11. Turn on your car. Enter the Delco unlock code using the procedure outlined by your GM owner's manual. Normally, the unlock code is entered with the "HR" and "MN" buttons on your radio.
  12. Press the AM/FM button. If you have entered the code correctly, your LED display will read "SEC" and the radio will be unlocked.

Hope this help.

Mar 18, 2010 | Car Speakers & Subwoofers

9 Answers

I need the code please for my Philips RC600 car stereo. PH600CY0142592 Thanks, Andrew


please explain your question.
like what code you need for your speaker?
Thanks

Jan 25, 2009 | Car Speakers & Subwoofers

1 Answer

Unlock code kenwood car stereo kdc-491


there are a few different ways to unlock according to model. I have posted 3 solutions.
1
During the code request mode, while holding the display key , press and hold the Volume UP or DOWN key for 3 seconds (so that “…” disappears).
Then using your remote enter your code.

2
Press the "Auto" button and "Track up" on face of radio at the same time. The four dash lines ( . . . . ) should "disappear".

Then using your remote enter your code.

3
Press and hold the 1 then the 6 preset key. "C" should display.
Then using your remote, enter your code.


Enter your number from the remote control unit. Your code number is 5227 (KCAR)

* Press numeric key “5” ( 2 times ) and press the Track UP/Next Track key
* Press numeric key “2” ( 3 times ) and press the Track UP/Next Track key
* Press numeric key “2” ( 1 time ) and press the Track UP/Next Track key
* Press numeric key “7” ( 2 times ) and press the Track UP/Next Track key

This should unlock your radio.
Have a great day!

May 29, 2008 | Car Speakers & Subwoofers

1 Answer

Need 1998 montero sport radio reset code


GETTING THE RADIO SERIAL NUMBER: <BR>
2000 - Carefully take the front panel off that surrounds the radio and temperature buttons, it will snap straight out. Wiggle the radio out about two inches, it is a tight fit. Get the serial number off the radio. It is on a sticker on the top, left side. Call a Mitsubishi dealer with the serial number. They will want proof of ownership, so have the title ready. After putting in the four digit serial number, hit the cd button and that enters it.The code is also written on an antitheft card that comes with the car and may be written in the owners manual in one of the back pages.
<BR> 1999 - Carefully remove the cup holder by pulling it out, then you will see the sticker with the radio serial number.
<BR> Other Years - I don't know an easy way to get the radio serial number, find a radio install savy person and ask them to help you. My dealership said they would do it for me and charge me for 30-60 mins worth of labor.. (At $75/hour) <BR> <BR>
RADIO SAYS "OFF" OR "LOCK": <BR>
Leave the "off" display on for 1 hour uninterupted, then it will automatically reset back to UNLOCK CODE.
<BR> When you turn it back on again after that time has passed it will ask for "code". <BR> <BR>
RADIO SAYS "UNLOCK CODE:" <BR>
Call your local MItsubishi dealership and ask for the service department.
<BR>They have a computer program where they punch in the serial number from your radio (you have to supply the number) and it will tell them the UNLOCK CODE for your radio. My dealership offered to give it to me free over the phone, if I knew my radio serial number. Enter the code using the buttons on your radio. And write the code down, this will show up everytime your radio looses connection to its power source - the car battery.

May 27, 2008 | Car Speakers & Subwoofers

Not finding what you are looking for?
Car Speakers & Subwoofers Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Car Speakers & Subwoofers Experts

xxxxxx xxx

Level 3 Expert

4706 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Car Speaker and Subwoofer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...