Question about InFocus ScreenPlay 7205 Multimedia Projector

1 Answer

Infocus Screenplay 7205 Projector

After turining off system thru my IR remote control, the unit power button begins to flash and doesn't stop. I tried disconnecting and re-connecting the unit but didn't help. Please help

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 563 Answers

Hi there

It might be a small IC that has gone on the Powerboard , I wouldn't worry about it if I were you.

Posted on Apr 15, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Thin black vertical lines in infocus projector screenplay 7205


normally, i'd say av solutions in ny, but they don't ship out of country. try www.projectordoctor.com.

Jan 22, 2010 | InFocus ScreenPlay 7205 Multimedia...

1 Answer

Lamp won't light and red light flashes 4 times


fan error. one of them aren't spinning as fast as it's supposed to. the lamp won't light as a safety precaution. you may need the fan replaced. you can either purchase a fan or send the projector in for repair. either way, try av solutions in ny. they're really good, and they are an authorized infocus service center. www.avsolutionsny.com

Nov 23, 2009 | InFocus ScreenPlay 7205 Multimedia...

1 Answer

Why does my projector Infocus 7205 says constantly replace lamp and we have a new lamp? Thanks for helping...


Hello,
On the projector you will see 2 buttons for adjusting the brightness, with the projector on press both the brightness up and down at the same time.
Hold them both pressed for 10 seconds. This will reset the lamp timer.

Take Care!

Nov 13, 2009 | InFocus ScreenPlay 7205 Multimedia...

1 Answer

My Infocus ScreenPlay 7205 has vertical lines throughout the whole picture when in use. Only about 1300 hours on the unit.


This could be an issue with the projector but here are some possible other causes.
1. make sure the wires running to the unit are not by any power source or other elctronic devices as this can cause interference.
2. use a differrent input source to check if the lines remain. (cable/satellite, dvd player, camcorder). if it does than it is most likely the projector.
hope this helps

Oct 18, 2009 | InFocus ScreenPlay 7205 Multimedia...

1 Answer

Need instructions on how to reassemble lamp and housing


For all Owners of Screenplay 7205.

The procedure to replace the lamp is illustrated on manual. Check at page 32 .

Manual available here: ScreenPlay 7205.

Apr 19, 2009 | InFocus ScreenPlay 7205 Multimedia...

1 Answer

Unable to switch off projector with remote (Infocus SP4805)


A bit unusual for the projector to stop responding to the remote. Usually it follows when someone has opened the projector, they forgot to reconnect the controls from the case top which also includes the IR receiver. If it isn't that, it could be a broken IR pc board or bad connection. I've seen that.

The worst case is that the IR controller on the main board has failed and if that's the case, you'll have to live with it as the cost of a new board is very high.

Mar 13, 2008 | InFocus ScreenPlay 4805 Multimedia...

1 Answer

Infocus Screenplay 7205


losing signal. reset the setting to factory default. adjust the clock and phase, too.

Jan 06, 2008 | InFocus ScreenPlay 7205 Multimedia...

Not finding what you are looking for?
InFocus ScreenPlay 7205 Multimedia Projector Logo

Related Topics:

109 people viewed this question

Ask a Question

Usually answered in minutes!

Top InFocus Office Equipment & Supplies Experts

Juan Carlos Pacheco

Level 1 Expert

36 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

The Knight
The Knight

Level 3 Expert

72640 Answers

Are you an InFocus Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...