Question about Amplifiers & Preamps

1 Answer

Reciever i have a kenwood amplifier and the thing turns on but wont output any sound. Its a home theater amp.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 319 Answers

Since Kenwood makes a lot of amps, I can't be specific. Check to see if speaker (A/B) is switched on. Make sure "mute" switch is off. If useing tuner, make sure to hook up AM/FM ant.

Posted on Apr 17, 2008

  • Randy Lierman Dec 15, 2013

    Where do I find the "mute" switch?

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can i hook up my kenwood stereo control amplifier KC-105 to my GPX home stereo system?


If the GPX has an headphone output you could use the a stereo headphone jack to two phono cables lead. Connect them to the "aux" socket of the amp, or another suitable - not a phono or deck - socket.
You would have to keep the volume level low on the GPX unit, but apart from that all the functions should work.

Aug 04, 2015 | Kenwood Amplifiers & Preamps

1 Answer

Kenwood integrated amplifier ka 895. Why no sound output?


How do you get to know that the unit turns on .After power up what are sequences happening i can help you

May 26, 2015 | Kenwood Amplifiers & Preamps

1 Answer

On my kenwood VR-5900 twospeaker wires touched and the reciever clicked off now when you turn it on it comeson for a sec. then clicks and shuts off. none of the fuses inside areblown what could be the...


When the two wires touched the short overheated and blew the output transistor or transistors. The unit needs to be repaired or replaced. It only takes a momentary touch of the wires to blow the output transistor. It is not a fault of your particular amp. It is common to all Solid State amps. Tube amps that have output transformers are not susceptible to this problem. Always shut off the amp when connecting or disconnecting the wires.

Oct 29, 2013 | Amplifiers & Preamps

1 Answer

14 speakers hooked up to home theater reciever,shuts off .5 vol


Hi,

Try less speakers.
The impedance will be to low for this amp.

Regards,
Gerard

May 10, 2010 | Yamaha P2500S Amplifier

1 Answer

My Kenwood KRFv5300D is working throught the tuner / radio channel but wont play sound from the TV - I have a digitial cable running from the amp to the TV but nothing else - should i have more cords then...


The only way it cCOULD work would be from a Digital Audio Output to a Digital Audio Input.

What is the model of the TV? Does it REALLY output a digital multichannel audio program? TV's aren't generally known for their audio chops and some of us own monitors with NO speakers or sound capabilities. Hence we buy things like Kenwood receivers and better speakers.

I would recommend that you draw the TV-related audio from the same place the TV gets it - Cable / DVD / BD. The audio hookup is simpler and the fewer intervening connnections, the better.

Apr 22, 2010 | Amplifiers & Preamps

1 Answer

7.1 preamp output


called onkyo and kenwood they explained in detail how to hook up.

Jan 06, 2010 | Onkyo M-282 2-Channel Amplifier

1 Answer

I have 1 center channel pre-out on back of my kenwood receiver. how do i hook it to the inputs on onkyo m-282 amp and then to center channel speaker?


Unfortunately can't connect it that way. The pre out is only meant to go directly into an amplifier that has all of the same inputs (front/rear, center and surround), not a standard receiver. (Pre amp to amp only, not pre amp to receiver) If your Onkyo doesn't have all the same inputs as your Kenwood preamp has outputs you will just use your standard left/right outputs from the Kenwood to your Onkyo input (CD, Tape, Phono,DVD etc) then use the outputs (front/rear, center and surround) from your Onkyo receiver and connect directly to your speakers..

Jan 01, 2010 | Onkyo M-282 2-Channel Amplifier

2 Answers

Kenwood amplifier


A home stereo system is not complete without an amplifier which drives the speakers. A preamp cannot drive a speaker. Try to read the labels at the back of the system...if it reads speaker then that is the amplifier output. Would you mind giving us what model is your system?

Sep 18, 2008 | Amplifiers & Preamps

1 Answer

Amplifier main channel non operational.


first pull out the power transistor then biased the output terminal. base,emitter have dc volts .4 to .5 collector to emitter have full voltage. if this voltage are in ur pre amp buy new trasistor

Sep 09, 2008 | Amplifiers & Preamps

1 Answer

Carver home amp


The DVD system problably doesent have PRE AMP outputs..you can take the record outputs from the DVD system and use them to connect to the input of the power amp. You then will need o use the Carvers volume controls as the volume controls as the record output of the DVD system will be a fixed output set at 0db.

Jul 27, 2008 | Amplifiers & Preamps

Not finding what you are looking for?
Amplifiers & Preamps Logo

Related Topics:

112 people viewed this question

Ask a Question

Usually answered in minutes!

Top Amplifiers & Preamps Experts

 Grubhead
Grubhead

Level 3 Expert

4584 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

The Knight
The Knight

Level 3 Expert

68223 Answers

Are you an Amplifier and Preamp Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...