Question about Kenmore Elite 45986 Front Load Washer

1 Answer

Ford contour 1999

My car heating died and my mph and rpm guagues went to zero the lights dimmed and I could not accelerate correlctly. I had the battery checked and it is fine. The battery light stays on and my car still starts. what is wronG ?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 178 Answers

Have autozone, or advanced auto check your altenator for proper voltage. You could be getting good amps to charge the system but the regulator in the altenator could be going bad and causing it to spike in charge or not push out enough voltage at all. This is normally a free test. Also, you may need to check the battery terminals for corrosion.

Posted on Apr 14, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi my beko tumble dryer wont heat up i have changed the pc board and the heating element what else could it be thanks


This could be the effect of a number of problems. Here's a list of things to check and details on how to do it.
  • Fuse could be bad -- Check the fuse for a break inside. If it's bad, replace it with an identical fuse.
  • Temperature switch could be bad -- Use VOM to check the switch. Set VOM to RX1, remove leads and touch the probes to the switch's terminals. The reading should be zero or infinity. Turn the switch, and the reading should change from zero to infinity or infinity to zero. If not, the switch is bad.
  • Thermostat could be bad -- Set the VOM to RX1, take a lead off one of the two outside terminals and press the probes to the two outside terminals. There should be a reading of zero. If not, it's bad.
  • Heating coils may be bad -- Set the VOM to RX1 and remove the leads from the coil. Press the probes to the terminals. If the reading is zero, the coil is bad.
  • Timer could be bad -- Disconnect the leads from the motor. Set the VOM to RX100. Clip the probes onto the leads. If the reading is infinity, the timer motor is bad.


Read more: http://www.doityourself.com/stry/repairdryer#ixzz2jQxE03Py

Oct 09, 2013 | Beko Tumble Dryer Heater/Thermostat...

1 Answer

Front load washer stuck on final spin


What is the complete model number of your unit?

Dec 10, 2012 | Washing Machines

1 Answer

Dryer stopped heating


this is likley to be the heat seconsers or its the heater/s burnd out if one of the elements have died on you it will only partly dry the washing,, not a hard job to fix but still a bit pricy,

Oct 24, 2009 | Kenmore 88732 Top Load Stacked Washer /...

1 Answer

While I was driving my 1999 ford contour se, I RPM gage began running at 5,000 and the speedometer jumped to 80 mph while I was in park. I then heard a low buzzing noise coming through my radio. My car...


I would bet the problem is somewhere in the wiring. It sounds to me like you have a short, most likely in your sensor wires for your tachometer and/or speedometer.

You should look under the hood and follow the wires from the tranny if you can. Another trick I've found helpful is to park the car in the garage and turn all the lights off and then try to start it. Look in the engine and see if you can spot any arcing.

This would also explain your battery problems.

Jul 29, 2009 | Kenmore Elite 45986 Front Load Washer

2 Answers

I have an lg dryer the cooling light is on and it does not heat


The cooling cycle was interupted some how within the processor. Remove power to dryer by breaker or unplugging for two hours and it will reset itself then repower and you are good to go.

Jun 29, 2009 | LG WM2688HWM TROMM SteamWasher

1 Answer

Slow oscillation, clicking in control panel, dimming lights


Hum. 1st I would check make sure power company is sending you the right Voltage.

2nd Make sure did not trip one side of breaker, Reset if needed.

3rd Pulling electrical circuits down could mean Start & or run capacitor is failing or failed. Or worse motor is failing.

Unless you know how to troubleshoot electrical systems might leave to tech Capacitors store voltage/amps & can harm or kill you.

I f I can help more MSG me back. Hope this helped. Please rate. Thank you. Good Luck!

Mar 12, 2009 | Washing Machines

1 Answer

KENMORE ELITE PROBLEM


Press and hold the control lock button down until the light goes off. This is a child proof feature that may have come on if you leaned against it to long. After lock light goes off you can use the machine.

Jul 21, 2008 | Kenmore Elite 45986 Front Load Washer

1 Answer

WASHER JAMS UP


from the description it sounds like the motor might be getting weak or something is getting caught underneath does it make any funny noises. let me know

Nov 05, 2007 | GE Profile Prodigy WPSE4200A

1 Answer

1999 Ford Contour - How do you get the alternator out!!!


2.5L Engines
  1. Disconnect the negative battery cable.
  2. Release the drive belt tensioner and remove the drive belt from around the alternator.
  3. Raise and support the vehicle.
  4. Remove the passenger side front wheel and fender well splash guard.
  5. Disconnect the passenger side outer tie rod end from the spindle. Refer to the Suspension & Steering Section.
  6. Remove the exhaust system Y-pipe.
  7. Unplug the connectors and remove the cables from the alternator.
  8. Remove the alternator brace retaining bolts and the brace from the vehicle.
  9. Remove the passenger side halfshaft, as outlined in the Drive Train Section
  10. Remove the alternator mounting bolts and remove the alternator from the passenger side fenderwell.

Sep 17, 2007 | Kenmore Elite 45986 Front Load Washer

Not finding what you are looking for?
Kenmore Elite 45986 Front Load Washer Logo

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Archaeology
Archaeology

Level 3 Expert

662 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...