Question about Kenmore Oasis 27042 Top Load Washer

1 Answer

F2 code Our washer beeps and the light s flash, and the F2 code comes up

Posted by on

  • Anonymous Mar 13, 2014

    f2 fault code is flashing, all lights on dial are flashing with a beeping noise

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,284 Answers

Hi, F2 code on the Kenmore indicates a problem with either of the control board and the user interface board. Run the console and indicators diagnostic test mode to find out.

Console and Indicators Diagnostic Test Mode Activation

  1. While in standby mode press the following button sequence within four seconds: SOIL LEVEL>WASH RINSE TEMP>SOIL LEVEL>WASH RINSE TEMP
  2. Press START within five seconds when "dt" shows on the display. All indicators in display are lit and "88" is displayed.
  3. Press START again. The two-digit display and the status indicators turn off while all other indicators remain lit.
  4. Press START again. The two-digit display and the status indicators turn on while all other indicators remain lit.
  5. Rotate the WASH CYCLE selector back and forth. The indicators will switch on an off.
  6. Press the buttons to check the functions. The indicators switch on and off and a beeping sound will be heard when a button is pressed.
  7. Press STOP or POWER button to exit diagnostic test mode.
  8. If no indicators light up or if no beeping sound is heard when a button is pressed or if some buttons do not light up indicators when pressed, check the control board, the user interface board, and the connection between them.
  • Unplug the machine.
  • Remove the three screws on the back of the console.
  • Lift the console off the cabinet.
  • The control board is located on the right side of the console viewed from the front of the machine. Disconnect the middle wiring harness connector on the right side of the control board near the pressure transducer hose.
  • Clean the connector and the terminals thoroughly with brush and alcohol.
  • Reconnect and disconnect the connector several times.
  • Reinstall the console and reconnect power.
  • If the problem is not resolved, replace the user interface board.
  • If the problem is still not resolved with the replacement of the user interface board, replace the control board. You may also replace both board at the same time and keep the old good board as a spare.
Take care

Posted on Jun 20, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The oven beeped, the screen said F3, now the oven is locked. It smells like a hot wire


What does F3 mean on my Frigidaire stove when it sounds ...

www.shopyourway.com > Manage My Life > Questions
My Frigidaire range beeps and flashes F3. ... 790.92413202 and when I turn on bake or broil it just shows an F3 code on the screen what does this mean?

What does fault codes "F2" and "F3" mean on a Kenmore ...

www.shopyourway.com > Manage My Life > Questions
I have a Kenmore wall oven model 911.41059591 that beeps and flashes F2 or F3 and shuts off. ... The "F2" and "F3" fault codes is most likely indicating an open oven ... Next, the control panel will need to be taken off in order to measure the ...

Oven error code "F2" and how to fix it ' AskGene.com

www.askgene.com/.../oven.../what-means-the-error-code-"f2"-on-your-o...
Mar 26, 2007 - The error code "F2" will be displayed along with a beeping sound if the

Jan 27, 2016 | Kitchen Ranges

2 Answers

How do I reset on a F2 ?


Going through all the comments mentioned above it seems that all of you have the same problem. Your appliance Control board is not working. Either try finding a new board or get it repaired.

To find a new replacement part/ part repair service. I would suggest www.partsimple.com part prices low compare to other competitors as well fast shipping.
TV parts Water Filter Washer parts Laptop Parts Replacement Parts...

Nov 10, 2014 | KitchenAid Kitchen Ranges

1 Answer

My washer will not complete the cycle or drain the clothes. It just stops and beeps then flashes an error code like F2.


And F2 translates to: long drain. Make sure the drain hose from the machine is not kinked or plugged. Do you hear the pump running when it is supposed to? Check the drain-pump filter for debris. Replace the pump if it doesn't seem to run. Hope this helps!

Feb 10, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Washer will not complete the cycle and drain the clothes. It stops and beeps and flashes an error code like F2 I think.


F-21 drain hose kinked,frozen.clogged, or more than 96 inchs above the floor.


If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Feb 10, 2010 | Washing Machines

1 Answer

I have a kenmore oasis elite it beeps all the time and flashes F2


Code F2 means a stuck button. I removed the interface and lightly sprayed each with contact cleaner. So far this is working. The interface costs about $160 and contact cleaner, $10. Good luck.

Mar 18, 2009 | Washing Machines

1 Answer

Dacor single oven flashes an F2 error code and won't stop beeping!!!


This is from manufacture service manual:

-F2- Alarm Heating Mode High Temperature
Is activated when the ERC senses a runaway heat condition or when the temperature exceeds
“runaway limits”. The ERC will beep until the cancel or another function is selected. If the alarm
repeats the F2 alarm check the oven sensor and wiring after fi rst checking for a stuck relay. If alarm
goes away verify the oven will complete a clean cycle without any type of failure.
Another words the problem with oven sensor or relay board.

I’m happy to help further over the phone at https://www.6ya.com/expert/vitaliy_f406165329c75ede

Oct 26, 2008 | Dacor MCS130 Millennia Electric Single...

1 Answer

Whirlpool washer need to be repaired


The f2 code is a pump problem. Need to look in pump. It is the first cycle to be satisfied when started.

Oct 19, 2008 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Kenmore Oasis Elite---110-27086601


This error only shows in diagnostic mode, with power off choose any buttons except stop and power, press in intervals 5 seconds on and 5 seconds off until 88 appears and all light light up. If the user panel is faulted F 2 will flash in the display, press the same button you used to start diagnostics to jump to the next error code and once through 88 will flash and diagnostics will start. Sometimes once F2 flashes and the machine has not been repaired it will stick at that mode.

Aug 07, 2008 | Kenmore Oasis HE 27082 Top Load Washer

1 Answer

Panel Beeping and F2 error code.


IT SOUNDS LIKE YOU GUYS HAVE A BAD KEYPAD/USER INTERFACE. LOOK IN THE SERVICE MANUAL FOR THIS TOPIC AND FOLLOW THE TEST:

ACTIVATION OF CONSOLE AND INDICATORS
DIAGNOSTIC TEST MODE

BOYNISMO@YAHOO.COM

Aug 05, 2008 | Kenmore Oasis HE 27087

Not finding what you are looking for?
Kenmore Oasis 27042 Top Load Washer Logo

116 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

fordexpert

Level 3 Expert

5692 Answers

Kristen Denison
Kristen Denison

Level 1 Expert

13 Answers

Jim Chinnery
Jim Chinnery

Level 1 Expert

10 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...