Question about Dishwashers

2 Answers

Whirlpool ADP951 modulogic - not working

Hi there,
Have just moved into new house which has a whirlpool ADP951 modulogic. Can't get it to run. Seems to be connected correctly (water and power) but there is a red light/signal that is lit up. It's located on the front left hand side of the dishwasher and looks like a snow flake in design. Any suggestions greatly appreciated.

Jen

Posted by on

2 Answers

It's the rinse aid led. Check the salt too

Posted on Jul 07, 2008

Try holding down the on button for three seconds and sometimes it will complete the cycle. ours doesn't start the whole time. check your water regulator valve under your sink, as it may be leaking which may cause the problem, in the process of replacing mine, but can't find the psi value

Posted on May 29, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Whirlpool dishwasher ADP951 that is not draining the water. I think the draining pump is broken. How much would it be to get a new pump and and get it fix?


If you use powder detergents or other "hard" detergent based products. They probably have backed up and clogged your dishwasher's drainage system.

**WARNING** Unplug any appliance before attempting to repair.


Step 1. Remove back panel from washer. (Use 1/4 or 3/8" screw bit & cordless screwdriver)
Step 2. Remove hose from pump. (Use channel locks or large pliars)
Step 3. Disassemble pump and remove clog or blockage from pump and hose.

Reverse process and plug in dishwasher and select a drain cycle if available.

Note: Do not use powder detergents if possible. They WILL clog any washer appliance.

Feb 10, 2011 | Whirlpool GU2400XTP Built-in Dishwasher

1 Answer

Whirlpool ADP6000WH Fault Code err 2


Hi, i have had my new dishwasher for less than 3 hours and is doing the same thing. Not happy Jan!!!! I have dishes everywhere, stuff out of the sink cupboard and a open house in 2 days. Watch out retravision in the morning!!!!!!! Did you get a solution to yours??

Jan 01, 2010 | Whirlpool 24 in. DU920PW Built-In...

1 Answer

Whirlpool ADP951,not operating


My advice, go buy a new one. If money is tight, go to the clearance aisle at Home depot and look for a scratch/dent discount model to replace it.

Old dishwashers were never good from the beginning. No point in fixing it - it was never designed well.

Nov 20, 2009 | Dishwashers

2 Answers

I have a whirlpool adp951 with a green light flashing


HI,
press back and forth between hi-tempwash and sani rinse several times to get all lights to come on if not then press sani rinse and heated dry back and forth several times. one of though combos will start the test mode


thank you for using fixya,rate my answer,
vijay

Oct 02, 2009 | Whirlpool 24 in. ADP5966 Free-standing...

1 Answer

Salty white dishes


Pour white vinegar into the rinse cycle, this should help.

Apr 12, 2009 | Whirlpool GU2400XTP Built-in Dishwasher

1 Answer

I have a Whirlpool dishwasher model ADP951. the green light is continually flashing and will not run, help with this would be most appreciated.


Have a look underneath dishwasher by removing front bottom access panel, the one touching the floor. Look for a round plastic disc about size of 4 jam lids together, centre front of dishwasher. Inside of it is a foam disc that will float up off the base of the dishwasher if water causes it to do so. This floating up will trip a switch. Clean base of dishwasher of water and maybe test the switch with multimeter. Reset fault by holding down start button.

Apr 26, 2008 | Whirlpool Dishwashers

1 Answer

Dishwasher, whirlpool generation 2000+


not enough info. new house? newly purchased house? new dishwasher? newly installed?
check to see if water line was connected
see if a valve has been inserted in water line and is open
if fools day joke, thanks for my time.

Apr 01, 2008 | Whirlpool GU2400XTP Built-in Dishwasher

1 Answer

Whirlpool dishwasher.


reach inside your d/w and jiggle the mushroom shaped float switch located on floor of d/w. should move freely up and down if its stuck up(or something lodged under it your unit wont fill with water

Feb 28, 2008 | Whirlpool GU2400XTP Built-in Dishwasher

1 Answer

Whirlpool ADP951 Dishwasher


Processor board sound bad. May be a loose plug ( or corroded connection on the plug ) . Unplug the dish washer from the wall plug before servicing. The open the front panel to expose the panel control board. Unplug the panel plugs and inspect them to assure no corrotion is apparent. If you see corrotion, use a pencil erracer to clean all contact points on the board and clean the plug the best possible. Plug the dishwasher plug back in the wall and check the unit for proper operation. If the operation is not correct, replace the circuit board. I hope this helps
Ed
NC Electronic
Mills, Wyoming

Jan 06, 2008 | Dishwashers

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

453 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Brad Brown

Level 3 Expert

13796 Answers

Are you a Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...