Question about Equalizers & Crossovers

Open Question

Replacement equalizer I need to replace the equalizer for my home stereo. It runs tuner, tape deck and cd player. so... what am I specifically looking for?

Posted by on

6 Suggested Answers

  • 4 Answers

SOURCE: equalizer hook up.

only hook up to tape monitor or else u wont get an audio signal . .....also hook all equipment to amplifier not eq ...it goes tape cd tuner and any type of external equipment to amp.then find tape 2 it sould be called tape moniter and have a separet botten for u to select it goes record to eq and play from eq

Posted on Nov 03, 2007

  • 189 Answers

SOURCE: sherwood 460 equalizer hook up

Connect the EQ to the Sherwood as if it were a tape deck: EQ's outs connect to receiver's tape ins (play) and EQ's ins connect to receiver's tape outs (record).
Then you hook the tape deck up to the tape ins and outs on the EQ: Tape deck outs connect to EQ's tape ins (play) and tape deck ins connect to EQ's tape outs (record).
This will put the EQ in your receiver's tape loop.
The CD player should be connected to the receiver though the CD in's and out's (or if your Sherwood doesn't have a CD in/out, then use AUX or TAPE2).
To hear the EQed signal with all receiver sources (like the CD player) you'll need to engage the 'Tape Monitor' button or switch which will route the tape loop to the speakers.

Posted on Jan 09, 2008

SirHanz
  • 145 Answers

SOURCE: Connect 5 piece Sony seperates stereo system

OK, this is pretty easy to do. First connect your leads from the component outputs(i.e., tape, cd, phono, etc) to the recievers corresponding input for the device. Then connect the recievers outputs to your equalizer, if it is a seperate eq. Then the outputs of that to your amplifier, then your speakers to that. Be sure all of your wires are connected with the proper polarity. These instructions may be a little different for your exact setup but basically follow the same order minus any device you dont have.

Posted on Feb 04, 2008

marsrover
  • 682 Answers

SOURCE: How to connect a Technics Graphic Equalizer to a JVC stereo system?

your situation is not so easy to solve but the ideal solution to connect everything to mixer(line in) and connect equalizer to main inserter in mixer(in this you got equalizer work with all media)(check mackie mixer dealer and ask about model have main inserter.

Posted on Jul 19, 2008

djproaudio
  • 515 Answers

SOURCE: Having a hard time connecting various audio components

Yes, it is a little tricky...

1) CD Changer (output) -> CD input on Amp

this is tricky... this will allow you to record to your tape deck, and control the sound via the EQ:
2) Tape Deck (tape out / recout) -> TAPE PLAYBACK on EQ
3) Tape RecOut on EQ -> Tape 1 Playback on Amp
4) Amp Tape 1 RecOut -> Tape Deck Playback / Input / RecIn
in essence, your creating a loop starting from the tape deck, going to the eq, then to the amp, then back to the tape deck to record.

Your EQ has another set of LINE IN and LINE OUT - use the second Tape 2 on the amp to create another loop. This will
allow you to control the EQ for any of the other sources.
5) LINE IN on EQ -> Tape 2 RecOut
6) Tape 2 Playback on Amp -> LINE OUT on EQ

5) Radio Tuner (output) -> Tuner input on Amp
6) DVD/VCR Combo Output -> AV/AUX on Amp

7) PC Computer... you don't have room for this. You can either use the PHONO input, and you'll have to purchase a Line Level Phono Converter
or, get a Y cable and split the signal and share with some other source.

Hope this helps.

- OPTiC
www.djproaudio.com
www.repairny.com

Posted on Dec 18, 2008

djproaudio
  • 515 Answers

SOURCE: Hooking up audio components

This was answered here: http://www.fixya.com/support/t1371668-having_hard_time_connecting_various

- OPTiC
http://www.djproaudio.com
http://www.repairny.com

Posted on Dec 18, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hooking up EQ to RECIEVER for a TECHNICS MODEL SH-8017


You'll need 4 connections total. On my integrated amp, I connected the four connections to all Line In and Line Out ports. And the other ends into the tape 2/EXTRA ports respectively.

Jul 19, 2013 | Panasonic Technics Stereo Graphic...

1 Answer

Connecting a tape deck and equalizer to a stereo receiver


Outs to Ins in a Tape Loop on the receiver. Model numbers make it easier if we or you can find the manuals for the receiver. If only one Tape Loop, nest the tape deck into the tape loop on the equalizer.

http://archiwumallegro.pl/technics_shge70-869230896.html

Sep 15, 2011 | Technics SH-GE70 Home Equalizer

2 Answers

Following a split from my boyfriend I really need some help in how to connect up my hifi system. It's all technics Tuner Receiver ST 610L Equaliser SH GE70 Amp SU V470 CD Changer SL...


the amp should have an in and out for the cassette player also,, so you would go from the Out on the receiver, to the in on the cassette,, and out of the cassette to the in on the receiver, I don't have nor can I locate that EQ , but basically,, you need to come out of the eq and back the same way you would a Cassette player,,

Jun 14, 2011 | Technics SH-GE70 Home Equalizer

1 Answer

I have a Amp,CD player,Tuner,and DVD player. no a tape deck.how can i conect all, with out a tape deck through eqeualizer.


You can connect the EQ on the tape in/output of your amplifier. Tape out (or monitor out) to the input of the EQ and tape in to the output of the EQ.
Listen to the tuner and than switch to the tape input, the tuner input will be still active. But in the tape "mode" your EQ will be active too.

Regards,
Gerard

Jan 10, 2010 | Yamaha EQ-70 Home Equalizer

1 Answer

Having a hard time connecting various audio components


Yes, it is a little tricky...

1) CD Changer (output) -> CD input on Amp

this is tricky... this will allow you to record to your tape deck, and control the sound via the EQ:
2) Tape Deck (tape out / recout) -> TAPE PLAYBACK on EQ
3) Tape RecOut on EQ -> Tape 1 Playback on Amp
4) Amp Tape 1 RecOut -> Tape Deck Playback / Input / RecIn
in essence, your creating a loop starting from the tape deck, going to the eq, then to the amp, then back to the tape deck to record.

Your EQ has another set of LINE IN and LINE OUT - use the second Tape 2 on the amp to create another loop. This will
allow you to control the EQ for any of the other sources.
5) LINE IN on EQ -> Tape 2 RecOut
6) Tape 2 Playback on Amp -> LINE OUT on EQ

5) Radio Tuner (output) -> Tuner input on Amp
6) DVD/VCR Combo Output -> AV/AUX on Amp

7) PC Computer... you don't have room for this. You can either use the PHONO input, and you'll have to purchase a Line Level Phono Converter
or, get a Y cable and split the signal and share with some other source.

Hope this helps.

- OPTiC
www.djproaudio.com
www.repairny.com

Dec 13, 2008 | Technics SH-GE90 Home Equalizer

1 Answer

Gemini Sound Products EQ-3000 equalizer


please connect as the following-----1-mp3 out-----to cd in in your receiver.
2-receiver rec out (tape put)----to equalizer in.
3-equalizer out----to tape in in receiver.

Sep 17, 2008 | Gemini Sound Products EQ-300 Home...

1 Answer

Conecting my EQ to my Yamaha reciever


your media out(dvd-cd-dat-deck player)-to equalizer in-and equalizer out to aux or cd in receiver.


Jul 17, 2008 | Yamaha EQ-70 Home Equalizer

2 Answers

Connect 5 piece Sony seperates stereo system


OK, this is pretty easy to do. First connect your leads from the component outputs(i.e., tape, cd, phono, etc) to the recievers corresponding input for the device. Then connect the recievers outputs to your equalizer, if it is a seperate eq. Then the outputs of that to your amplifier, then your speakers to that. Be sure all of your wires are connected with the proper polarity. These instructions may be a little different for your exact setup but basically follow the same order minus any device you dont have.

Feb 03, 2008 | Equalizers & Crossovers

1 Answer

Sherwood 460 equalizer hook up


Connect the EQ to the Sherwood as if it were a tape deck: EQ's outs connect to receiver's tape ins (play) and EQ's ins connect to receiver's tape outs (record).
Then you hook the tape deck up to the tape ins and outs on the EQ: Tape deck outs connect to EQ's tape ins (play) and tape deck ins connect to EQ's tape outs (record).
This will put the EQ in your receiver's tape loop.
The CD player should be connected to the receiver though the CD in's and out's (or if your Sherwood doesn't have a CD in/out, then use AUX or TAPE2).
To hear the EQed signal with all receiver sources (like the CD player) you'll need to engage the 'Tape Monitor' button or switch which will route the tape loop to the speakers.

Jan 09, 2008 | Equalizers & Crossovers

1 Answer

Equalizer hook up.


only hook up to tape monitor or else u wont get an audio signal . .....also hook all equipment to amplifier not eq ...it goes tape cd tuner and any type of external equipment to amp.then find tape 2 it sould be called tape moniter and have a separet botten for u to select it goes record to eq and play from eq

Aug 27, 2007 | Spectrum Technical Hifi EQ-B5100...

Not finding what you are looking for?
Equalizers & Crossovers Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Equalizers & Crossovers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

5653 Answers

The Knight
The Knight

Level 3 Expert

68368 Answers

Are you an Equalizer and Crossover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...