Question about Maytag Washing Machines

1 Answer

Maytag mah4000aww motor control board bad cannot tell which series it is serial 53312313yk

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

My front load washer is leaving water after done spin cycle can still ring water out of clothing....water is draining from hose and is spinning somewhat strange...like its not going through rinse properly sorta like its repeatedly doing same cycle pattern...spins for lil, stops makes running noses...spins sum more....soapy clothing...its 5 years old..but first time use this month finally connected it...when took bottom off to check hose connection noticed control board looked lil warped and brownish colored but not as meant to be..maybe its burnt out?

Posted on Sep 10, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Maytag washer MAH4000AWW timer will not advance. Washer will operate if I manually advance timer. Have changed timer, followed Drive System diagnostic test, the wax motor and control board were replaced a...


there is a motor inside the timer that turns the knob. the problem must be the replacement timer. was it a brand new timer from maytag or a 2nd hand? also double check your timer is connected correctly.

Nov 08, 2013 | Maytag Washing Machines

1 Answer

Door light wont come on and dor wont lock, also replaced control board with new on and burned hole in it just like original


Hi, The wax motor of the door lock is the problem that is burning up the boards, replace the redish brown wax motor in the door lock assembly

Sep 24, 2012 | Washing Machines

1 Answer

Maytag MAH4000AWW no longer does the high speed spin cycle. Other than that motor runs fine. Seems like a controller issue but don't have a repair manual to know for sure.


http://www.searspartsdirect.com/partsdirect/part-model/Maytag-Parts/Washer-Parts/Model-MAH4000AWW/3048/0153200/M0603006/00013?blt=06&prst=0&shdMod=MAH4000AWW

It could be the motor control board not telling the motor to switch to its highest speed, but it could also be control board not telling the motor control board to activate, but it could also be in the timing circuit. What other indications are you getting? Take a look at the wiring diagrams for this machine on the referenced site.

Jul 01, 2011 | Maytag Washing Machines

1 Answer

Neptune front loader. doorlock light quit working. wont spin.


You will need to change the machine control board and door lock wax motor.
MAH3000AWW PART # 'S 22002988 AND 12002535
MAH4000AWW PART# 'S 22002989 AND 12002535
If yo look at your control board in the control panel you will find R11 burned.

Jun 10, 2011 | Maytag Washing Machines

1 Answer

I have a burned out resister which I need to replace.


R11 = 3.9 K ohm 1/4 w If Q6 burned,change by NTE5657 ( 600v)

Jun 17, 2009 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

Maytag Neptune washer model #MAH4000AWW, Press start botton starts filling then shuts off after a few seconds. Move to spin it begins draining then shuts off after a few seconds


Check out your motor control board near the floor on the right side. These have a high failure rate on the Neptunes. Maytag redesigned both the motor and motor control board to be more reliable. While inspecting this board, you are looking for a blown 10 amp fuse and /or burnt components. If you have either... then you will need the the new motor conversion kit which includes the motor, motor control board and the wire harness.

These kits are offered on the www.neptunewaxmotor.com order form and they ship UPS Ground.

This kit takes about an hour to install.


Don't forget to see the info on the website regarding the defective door latch wax motor that will eventually fail and damage your machine control board.



Jul 14, 2008 | Washing Machines

2 Answers

Neptune MAH4000AWW


If there are no errors then the motor controller thinks everything is ok.
Do you hear the motor spinning?

the belt in the back may be bad or jumped off.
If you want to look for yourself open the top panel.(3 screws in top rear)

Jan 24, 2008 | Maytag MAH6700AWW Neptune Front-Load...

3 Answers

Maytag Neptune MAH4000AWW washer door will not unlock


no, the board and wax motor is one possible problem but more likely youll need the motor kit with spped control. even more expesive but prove to be a big problem with this washer

Nov 18, 2007 | Whirlpool Gold Duet GHW9400P 3.8 Cu. Ft....

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

657 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Bill Long

Level 3 Expert

587 Answers

John Tripp
John Tripp

Level 3 Expert

4654 Answers

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...