Question about Hobart 24 in. LXIC-5 Built-in Dishwasher

1 Answer

Hobart lx18 What is the expected cost to repair Hobart lx18 with code P2?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Contributor
  • 68 Answers

$0. Clean the probes. Two in back right corner. Two under the front screen. Use a green scrubby.

If the problem persists, check where the water comes into the machine. There is a screen on the hose that clogs up and starves the machine for water.

Posted on May 02, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Repairman can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Repairman (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i test heating elements on Hobart LX18


Use an ohm meter you should get a low ohm-age reading.

Jan 05, 2017 | Hobart Dishwashers

1 Answer

I have a hobart lx18 and when i plugged it in, it started smoking


I have to asume the wiring connections had not changed since it last worked.
There are three versions. LX18, LX18C and LX18H.
Inspect the relay board for damage. The connections can come loose and melt relays.
It could also be the wash sump tank heater or the booster heater if it's an H. The other two only have a sump heater. If you power it on, and have no water in it's tanks, the elements can glow red hot till they trip the high limits.

Feb 25, 2014 | Hobart Dishwashers

1 Answer

Hobart AM15T ML-130039 with p2 message, what does this code mean


p2 would mean your rinse thermistor is open or shorted. its located on top near the the right side, after the vac. brkr. part# is 328994. remove old, istall new . dont forget to vote,hope this helps , monomoy

Jan 29, 2010 | Hobart 29 in. AM15-1 Free-Standing...

1 Answer

Leak in the recyling tube on our Hobart LX18 diswasher, need to order new tube


that is called the wash pipe the part# for the pipe is 893457. that can be bought @any hobart office in your area

Jan 04, 2010 | Hobart 24 in. LXIC-5 Built-in Dishwasher

1 Answer

Lx30h P2 ERROR CODE? WON'T DRAIN COMPLETELY - HELP


the p2 err. is on open or shorted rinse thermistor which is located on the back of the mach next to the vac. brkr. as for draining ck the drain valve for debris, and the end of the drain hose where it connects to the building drain

Dec 25, 2009 | Hobart 24 in. LXIH-3 Built-in Dishwasher

1 Answer

Hobart lx18 Dishwasher wont fill up


Frank,does the sump probe (the one underneath the screen) look good?It should have at least one quarter inch of metal.I have seen these break and its hard to tell but the info your describing sounds like that probe is bad or the control board.I'm a hobart tech and can help you troubleshoot,let me know----Tony

Nov 21, 2009 | Hobart Dishwashers

1 Answer

Temperature Problem


Whats the model?lxih,lx30h,lx18,lx40?What temps are low,wash or rinse?Im a hobart tech and service these units.Let me know.

Jan 19, 2009 | Hobart 24 in. LXIC-5 Built-in Dishwasher

3 Answers

Hobart LX 30 P2 Error and unit overflowing!


Hi drogers77,

I'm not a Hobart technician, but here what I founded in my manual for the LX30 error message:

LX18 / LX30 display shows E0, E2, E3 or E4

1. Low water pressure - check for clogged hose strainer; check that site water pressure meets minimum flow pressures.

2. Make sure probes are clean

3. No water pressure - main water supply valves may not be working

4. Drain valve open - turn machine OFF to drain machine, then ON. Repeat twice (this assists in clearing any drain valve obstructions). Wait for machine to reach READY mode and press WASH. Slowly open door several seconds later and note water level. Close door; 30 seconds later, open door slowly and check that water level is the same as it was. If not, repeat the OFF-ON procedure. If problem persists, call your local Hobart Service Office.

5. Delime machine.

Hope it will help you.

pepsicrazy

Dec 27, 2008 | Hobart 24 in. LXIH-3 Built-in Dishwasher

Not finding what you are looking for?
Hobart 24 in. LXIC-5 Built-in Dishwasher Logo

Related Topics:

811 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hobart Dishwashers Experts

Jason

Level 2 Expert

211 Answers

yadayada
yadayada

Level 3 Expert

77201 Answers

Garth Jackson

Level 2 Expert

93 Answers

Are you a Hobart Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...