One day i noticed a message on the lcd saying overload. It will not turn on now>?? How can i fix this

Sir/Madam
Hear is the solution For Your Problem,Just Watch The Video On And Fix Your Brother Printer Issue,
www.youtube.com/watch?v=BxbJbXf1u9w

or Go to Brother Official Web Site ->FAQ's & Troubleshooting ->Error Messages (LCD, PC) or LED Lights > faq002555_00

I Hope By Now You Fixed Your Problem Brother Printer Support

Dear inVaUSA, I followed your action and contacted 1-800-SAMSUNG but did not fare as well as you did. I was told there is not a firmware update nor a patch to fix the "New Device Not Found USB1 Power Overload" even after I read your post to the support representative I was dealing with. She told me that it is a PlayStation issue even though I have never connected any USB device to any USB Port on my Samsung TV. Could I Please trouble you to send me the firmware update you received from Samsung `in a private message or to my email address if you prefer. Thank you!

Hello Edward Garcia,

Indeed yes... you have a 2004 Manufacturer
RECALL CAMPAIN... Notice SC-04-002

FIRST technical Service Bulletin I looked at...

ETACS-ECU Excessive battery drain...

Gives the location and required
>> dealer RE-programming of keys & fobs...

Principally presents on cars left sitting for 7 to 10 days
((they were talking "NEW" cars... I imagine those dynamics change SIGNIFICANTLY with old batteries))...

Attributed to POOR PROGRAMMING...

REMEDY: replacement

Location.. lower dash... between steering wheel & door

Use the FREE TSB database ... provided by
BBB Industries...
(registration is required: these are REAL DOCUMENTS)

http://bbbid.com/

Hope this helped

Carnac the Magnificent

If you wish to get some details; visit the site linked here. Pull up older posts.
http://electronicshelponline.blogspot.com/
faults & possible causes to LCD & Plasma screen are given with illustrations. You can get an idea about the fault to an extent. Faults to all LCD & Plasma screen are similar, irrespective of its brand and screen size.

Overload  usually only appears if you have been using higher volumes for a period of time and this trips to protect your speakers and amplifier. Turning off your amplifier and leaving for a while and it automatically resets. other wise a would check your speaker cabling to see if any wires are  touching shorting out the circuit. Try removing you cables from your amp then turn on. If it turns on without Overload appearing the problem is between amp and speakers. Check your cables at both ends and while at it give them a clean then hook up everything ( Amp should be off) then turn on the amp and see if you get message. If you still get this message you could have  dry/ broken soldering on the inside and the amp is detecting a dc short in the system. This seem to a common thing these days. In which it will be a repair job.  Low impedance speakers or speakers that have a wide impedance swing when they are running at high volume can cause a amp to trip if it hasn't got enough current to drive low impedance speakers. Hope this has been of help.

We have the same model of monitor and had the same problem few days ago. The monitor just goes black/turns off. I noticed that the power button has a yellow blinking light and cannot be turn on/off again using the power button. The CPU is working fine also. When I turn off the avr, the power button's light turns blue for a few second and you can hear a click sound from the back of the lcd before it totally turns off. My lcd monitor is over a year old now and is 110v or 220v capable. Mine was originally in a 220v, i just put it in 110v and the monitor was fixed.. Hope this can somehow fix your problem.

This is a variant of the "protect" mode for receivers. This indicates that a problem was detected in the final stage of the output amplifier and the unit has shutdown to prevent further damage. The "fix" for this is to replace either the output transistors or the amp-pac. I don't know which variant is used in your specific model. If it is the output transistors, expect a parts cost in the $15-$30 range. If an amp-pac, the parts will run in the $75-$100 range. Dan

The overload message is the old version of "protect" mode. This means that a problem has been detected in the output amp section and that section is shutdown to prevent further damage. Your unit uses amp-pacs. One or more are bad. These are marked RSN3305P and cost about $66 each.

Dan

You can't do it yourself only a good technician or repair center.I don't know the fix it cost.